Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Cook announcer pin out

Status
Not open for further replies.

informidicate

Vendor
Jan 17, 2007
113
US
I hope one of you old timers ( I am one ) may have the
pin out's for a Cook announcer that has the 20 pin wire
wrap connectors on the back, I am not having much luck
trying to find it on the Web.
Any help would be appreciated.
 
Is this what you are looking for?

Ensing, Inc has received many telephone calls regarding the
installation of a Cook Digital Announcer (Cook DA) to an
NT8D14 Universal Trunk Card. In order to use a Cook DA in
Start-Stop mode, you must use an NT8D14BA or later vintage
trunk card.
A Cook DA can be used in continuous operation mode with any
vintage NT8D14 trunk card.

The following charts relate the color of the pair of the cable
coming from the MDF to the color of the pair of the cable going
to the Cook DA.

NT5M DIGITAL ANNOUNCER - NT8D14 WIRING (Continuous Run Mode)

|------------------------------------ 25 pr cable from NT8D14
| |---------|-------------------- 25 pr cable to Cook DA
| | | |----------- Signal Name on Cook DA
| | | | |------ Description of signal
| | | | |
| | | | |
COLOR COLOR PIN# SIGNAL DESCRIPTION
------------------------------------------------------------------
NT8D14 PORT 0
w/bl br/y 19 T1 TIP CONNECTION, CH.1
bl/w y/br 44 R1 RING CONNECTION, CH.1
w/or gr/v 23 C1 BREAK RELAY CONTACT C, CH.1
or/w bl/v 21 BY1 BUSY CONTACT BY, CH.1

Strap pins 45,46,47,48 of the Cook DA to Ground.
Strap pin 22 of the Cook DA to -48v.
Set dip switch S1-3 to on, S1-2 to off and S1-7 to off.
Configure the trunk route as RTYP=AUD (Audichron) in LD 16.

------------------------------------------------------------------
NT8D14 PORT 1
w/gr gr/bk 13 T2 TIP CONNECTION, CH.2
gr/w bk/gr 38 R2 RING CONNECTION, CH.2
w/br or/y 17 C2 BREAK RELAY CONTACT C, CH.2
br/w sl/bk 15 BY2 BUSY CONTACT BY, CH.2

Strap pins 39,40,41,42 of the Cook DA to Ground.
Strap pin 16 of the Cook DA to -48v.
Set dip switch S1-3 to on, S1-2 to off and S1-7 to off.
Configure the trunk route as RTYP=AUD (Audichron) in LD 16.

------------------------------------------------------------------
NT8D14 PORT 2
w/sl or/r 7 T3 TIP CONNECTION, CH.3
sl/w r/or 32 R3 RING CONNECTION, CH.3
r/bl bl/bk 11 C3 BREAK RELAY CONTACT C, CH.3
bl/r br/r 9 BY3 BUSY CONTACT BY, CH.3

Strap pins 33,34,35,36 of the Cook DA to Ground.
Strap pin 10 of the Cook DA to -48v.
Set dip switch S1-3 to on, S1-2 to off and S1-7 to off.
Configure the trunk route as RTYP=AUD (Audichron) in LD 16.

------------------------------------------------------------------
NT8D14 PORT 3
r/or bl/w 1 T4 TIP CONNECTION, CH.4
or/r w/bl 26 R4 RING CONNECTION, CH.4
r/gr sl/w 5 C4 BREAK RELAY CONTACT C, CH.4
gr/r gr/w 3 BY4 BUSY CONTACT BY, CH.4

Strap pins 27,28,29,30 of the Cook DA to Ground.
Strap pin 4 of the Cook DA to -48v.
Set dip switch S1-3 to on, S1-2 to off and S1-7 to off.
Configure the trunk route as RTYP=AUD (Audichron) in LD 16.
---------------------------------------------------------------
----------------------------------------------------------------
----------------------------------------------------------------

NT5M DIGITAL ANNOUNCER - NT8D14 WIRING (Pulse Start Mode)
(NT8D14BA or higher vintage required)

|------------------------------------ 25 pr cable from NT8D14
| |---------|-------------------- 25 pr cable to Cook DA
| | | |----------- Signal Name on Cook DA
| | | | |------ Description of signal
| | | | |
| | | | |
COLOR COLOR PIN# SIGNAL DESCRIPTION
------------------------------------------------------------------
NT8D14 PORT 0
w/bl br/y 19 T1 TIP CONNECTION, CH.1
bl/w y/br 44 R1 RING CONNECTION, CH.1
w/or gr/v 23 C1 BREAK RELAY CONTACT C, CH.1
or/w v/or 47 ST1+ POSITIVE START LEAD, CH.1

Strap pins 45,46,48 of the Cook DA to Ground.
Strap pin 22 of the Cook DA to -48v.
Set dip switch S1-3 to off, S1-2 to on.
Configure the trunk route as RTYP=CK2 (Cook 201) in LD 16.

------------------------------------------------------------------
NT8D14 PORT 1
w/gr gr/bk 13 T2 TIP CONNECTION, CH.2
gr/w bk/gr 38 R2 RING CONNECTION, CH.2
w/br or/y 17 C2 BREAK RELAY CONTACT C, CH.2
br/w y/bl 41 ST2+ POSITIVE START LEAD, CH.2

Strap pins 39,40,42 of the Cook DA to Ground.
Strap pin 16 of the Cook DA to -48v.
Set dip switch S1-3 to off, S1-2 to on.
Configure the trunk route as RTYP=CK2 (Cook 201)in LD 16.

------------------------------------------------------------------
NT8D14 PORT 2
w/sl or/r 7 T3 TIP CONNECTION, CH.3
sl/w r/or 32 R3 RING CONNECTION, CH.3
r/bl bl/bk 11 C3 BREAK RELAY CONTACT C, CH.3
bl/r r/sl 35 ST3+ POSITIVE START LEAD, CH.3

Strap pins 33,34,36 of the Cook DA to Ground.
Strap pin 10 of the Cook DA to -48v.
Set dip switch S1-3 to off, S1-2 to on.
Configure the trunk route as RTYP=CK2 (Cook 201) in LD 16.

------------------------------------------------------------------
NT8D14 PORT 3
r/or bl/w 1 T4 TIP CONNECTION, CH.4
or/r w/bl 26 R4 RING CONNECTION, CH.4
r/gr sl/w 5 C4 BREAK RELAY CONTACT C, CH.4
gr/r w/br 29 ST4+ POSITIVE START LEAD, CH.4

Strap pins 27,28,30 of the Cook DA to Ground.
Strap pin 4 of the Cook DA to -48v.
Set dip switch S1-3 to off, S1-2 to on.
Configure the trunk route as RTYP=CK2 (Cook 201) in LD 16.

 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top