Configuring SIP Trunk Between HiPath 4K and OpenScape Business

[SaeedAyman]

I need to configure a SIP Link between my HiPath 4K and my OpenScape Business V2.
The thing is, I have problems in both of the configurations.

- For the HiPath 4K:
I have the configurations, for configuring my STMI card to operate 120 HFA phones, 120 SIP phones and 10 SIP trunks

ADD-BFDAT:FCTBLK=1,FUNCTION=HG3530&HG3550&SIP,BRDBCHL=BCHL60;
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=HG3530,LINECNT=120,BCHLCNT=30;
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=HG3550,LINECNT=1,UNITS=1;
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=SIP,LINECNT=120,BCHLCNT=30;
CHANGE-BFDAT:CONFIG=OK,FCTBLK=1,ANSW=YES;

ADD-BCSU:MTYPE=IPGW,LTG=1,LTU=5,SLOT=79,PARTNO="Q2324-X500",FCTID=1,LWVAR="0",FCTBLK=1,BCHL3530=60,BCHLSIP=30,BCHL3550=30,ALARMNO=0,IPMODE=IPV4,DHCPV4=NO,DHCPV6=NO;

ADD-CGWB:5,79,NORMAL,172. 16. 90.110,255.255.255.0;
CHANGE-CGWB:MTYPE=CGW,LTU=5,SLOT=79,TYPE=GLOBIF,PATTERN=213,VLAN=NO,VLANID=0,
DEFRT=172.16.90.1,TCPP=4060,BITRATE=100MBFD,TRPRSIP=10,TRPRSIPQ=0,TRPRH323=0,TPR
H323A=0,TLSP=4060,DNSIPADR=0.0.0.0,DNSIPAD2=0.0.0.0;
CHANGE-CGWB:CGW,5,79,SERVIF,"TRM";
CHANGE-CGWB:CGW,5,79,ASC,29100,29219,184,104,YES,YES,YES,YES,PRIO1,G711A,NO,30;
CHANGE-CGWB:CGW,5,79,ASC,,,,,,,,,PRIO2,G729A,NO,20;
CHANGE-CGWB:CGW,5,79,ASC,,,,,,,,,PRIO3,G723,NO,30;
CHANGE-CGWB:CGW,5,79,ASC,,,,,,,,,PRIO4,NONE,NO,20;
CHANGE-CGWB:CGW,5,79,ASC,,,,,,,,,PRIO5,NONE,NO,20;
CHANGE-CGWB:CGW,5,79,ASC,,,,,,,,,PRIO6,NONE,NO,20;
CHANGE-CGWB:CGW,5,79,ASC,,,,,,,,,PRIO7,G729AB,YES,20;
CHANGE-CGWB:CGW,5,79,DSP,60;
CHANGE-CGWB:CGW,5,79,GKDATA,,1719,"PRIMARYRASMANAGERID",,,1719,"SECONDARYRASMANAGERID",,120;
CHANGE-CGWB:CGW,5,79,MGNTDATA,,8000,,443;
CHANGE-CGWB:CGW,5,79,DMCDATA,0;
CHANGE-CGWB:CGW,5,79,WBMDATA,"HP4K-DEVEL",,ENGR;
CHANGE-CGWB:CGW,5,79,WBMDATA,"HP4K-SU",,SU;
CHANGE-CGWB:CGW,5,79,WBMDATA,"HP4K-ADMIN",,ADMIN;
CHANGE-CGWB:CGW,5,79,WBMDATA,"HP4K-READER",,READONLY;

CHANGE-CGWB:CGW,5,79,WBMDATA,"AHMED",,ENGR;

CHANGE-CGWB:CGW,5,79,GWDATA,"PRIMARYRASMANAGERID",;
CHANGE-CGWB:CGW,5,79,H235DATA,NO,NO,"siemensGateway2003",,100,242-191-30-119-188-83-173-161-43-0-70-36-218-74-169-221-78-102-174-170;
CHANGE-CGWB:CGW,5,79,LEGKDATA,1,192168197,NO;
CHANGE-CGWB:CGW,5,79,SIPTRERH,NO,,,;
CHANGE-CGWB:CGW,5,79,SIPTRSSA,NO,0.0.0.0,5060,5061,120,0.0.0.0,5060,5061;
CHANGE-CGWB:CGW,5,79,DLSDATA,,10444,NO;

CHANGE-CGWB:CGW,5,79,JB,40,120,20,4,60,200,2;

RES-BSSUEN,,5,79;
ADD-COP:202,L3AR&RRST,,;
ADD-COT:202,PRI&RCL&XFER&ANS&USD&AEOD&KNOR&CEBC&CBBN&CBFN&COTN&IEVT&BSHT&BLOC&PROV&LWNC&ATRS&ROPT&NLCR&TSCS&TRSC&DFNN&CFOS&NLRD&PINR&AOCC&LINO&NQPI&NOFT&NQNP&AMFC&IBBA&NTON;

ADD-BUEND:202,"MATRIX",30,0,*,2,ON,0,0,NEUTRAL;
ADD-TDCSU:OPT=NEW,PEN=1-5-79-60,COTNO=202,COPNO=202,DPLN=0,ITR=0,COS=25,LCOSV=1000,LCOSD=1,CCT="IP TRUNK ",DESTNO=254,PROTVAR=PSS1V2,SEGMENT=8,DEDSVC=NONE,TRTBL=GDTR,SIDANI=N,ATNTYP=TIE,CBMATTR=NONE,TCHARG=N,SUPPRESS=0,TRACOUNT=31,SATCOUNT=MANY,NNO=999,ALARMNO=0,FIDX=1,CARRIER=1,ZONE=EMPTY,COTX=51,FWDX=1,CHIMAP=N,CCHDL=SIDEA,UUSCCX=16,UUSCCY=8,FNIDX=1,NWMUXTIM=10,CLASSMRK=EC&G711&G729AOPT,TCCID="",TGRP=202,SRCHMODE=DSC,INS=Y,SECLEVEL=SECURE,DEV=HG3550IP,BCHAN=1&&10,BCNEG=Y,BCGR=1,LWPAR=1,LWPP=0,LWLT=0,LWPS=0,LWR1=0,LWR2=0,DMCALLWD=N;
ADD-RICHT:MODE=LRTENEW,LRTE=202,LSVC=ALL,NAME="IP TRUNK ",TGRP=202,DNNO=0,ROUTOPT=YES,REROUT=NO,DTMFTEXT="",PLB=NO,ROUTATT=NO,EMCYRTT=NO,INFO="",PDNNO=0,CHARCON=NEUTRAL,CONFTONE=NO,RERINGRP=NO,NOPRCFWD=NO,NITO=NO,CLNAMEDL=NO,FWDSWTCH=NO,LINFEMER=NO,NOINTRTE=NO;
ADD-GKREG:GWNO=1,GWATTR=INTGW&REGGW&SIP&HG3550V2,DIPLNUM=0,DPLN=0,LAUTH=1;
ADD-GKREG:GWNO=2,GWATTR=EXTGW&REGGW&HG3550V2&SIP,GWIPADDR=172.16.90.115,GWDIRNO=999,DIPLNUM=0,DPLN=0,LAUTH=1,INFO="",SECLEVEL=TRADITIO;

My question is, do I need to configure my dial plan as an open numbering system (LDPLN, etc.) and enter each number in my dial plan in my LDPLN table, or can I configure it as a closed numbering system?


- For the OpenScape Business:

I do not know the configuration on this side


Thanks a lot.

 

[donb01]

At first glance, I don't see any configuration on the 4000 for the SIP trunks is one thing I notice, the second thing I notice is your 120 + 120 + 10 = 250, and I think you can only put 240 devices on an STMI4 card.

That was it for my first glance. I'm not familiar with the OS Biz.

Don Bruechert, Voice Comm Analyst II
CareTech Solutions @ Holy Family Memorial
Manitowoc, WI, USA