Hi,
I have a customer with 3 x port networks as follows in a PNC duplicated system - direct connect with TN570 Fiber boards:
01A / 01B
02A / 02B
03A / 03B
PORT NETWORK CONNECTIVITY
Duplicated? yes
Software Locked? no
Standby Busied? yes
Direct Connect? yes
Standby Refreshed? no
Interchange Disabled? no
Center Stage Switch Enabled? yes
A-PNC B-PNC
Mode: active Mode: standby
State of Health: functional State of Health: functional
Inter PN Index: 00.00.00.00.00.00 Inter PN Index: 00.00.00.00.00.00
Inter SN Index: 00.00 Inter SN Index: 00.00
Major Alarms: 6 Major Alarms: 0
Minor Alarms: 0 Minor Alarms: 0
Warning Alarms: 1 Warning Alarms: 2
SN Locations: SN Locations:
They have been upgraded a few time since CM2 and now they are on CM6.3.
No one has bothered to try to remove the Fiber Boards and change to IP connect with active/stanby IPSI's in each PN.
'change system-parameters duplication' = Enable Operation of IPSI Duplication? y
'list ipserver-interface' =
Port Pri/ Primary/ Primary/ Primary/ State Of
Ntwk Sec Secondary Secondary Secondary Serv Control Health
Num Bd Loc IP Address Host Name DHCP ID State State C P E G
---- ------ --------------- ---------------- --------- ----- ------- -------
1 1A01 222.222.222.201 222.222.222.201 ipsi-A01a OUT active 0.1.1.0
1B01 222.222.222.202 222.222.222.202 ipsi-A01b OUT standby 0.1.1.0
2 2A01 n/a
2B01 n/a
3 3A01 n/a
3B01 n/a
How do I remove the Fiber boards and enable IP connect on all IPSI's
many thanks
I have a customer with 3 x port networks as follows in a PNC duplicated system - direct connect with TN570 Fiber boards:
01A / 01B
02A / 02B
03A / 03B
PORT NETWORK CONNECTIVITY
Duplicated? yes
Software Locked? no
Standby Busied? yes
Direct Connect? yes
Standby Refreshed? no
Interchange Disabled? no
Center Stage Switch Enabled? yes
A-PNC B-PNC
Mode: active Mode: standby
State of Health: functional State of Health: functional
Inter PN Index: 00.00.00.00.00.00 Inter PN Index: 00.00.00.00.00.00
Inter SN Index: 00.00 Inter SN Index: 00.00
Major Alarms: 6 Major Alarms: 0
Minor Alarms: 0 Minor Alarms: 0
Warning Alarms: 1 Warning Alarms: 2
SN Locations: SN Locations:
They have been upgraded a few time since CM2 and now they are on CM6.3.
No one has bothered to try to remove the Fiber Boards and change to IP connect with active/stanby IPSI's in each PN.
'change system-parameters duplication' = Enable Operation of IPSI Duplication? y
'list ipserver-interface' =
Port Pri/ Primary/ Primary/ Primary/ State Of
Ntwk Sec Secondary Secondary Secondary Serv Control Health
Num Bd Loc IP Address Host Name DHCP ID State State C P E G
---- ------ --------------- ---------------- --------- ----- ------- -------
1 1A01 222.222.222.201 222.222.222.201 ipsi-A01a OUT active 0.1.1.0
1B01 222.222.222.202 222.222.222.202 ipsi-A01b OUT standby 0.1.1.0
2 2A01 n/a
2B01 n/a
3 3A01 n/a
3B01 n/a
How do I remove the Fiber boards and enable IP connect on all IPSI's
many thanks