CLID from 1000E

[DAS1512]

Dear Friends,

In one of my site I have Cs1000T and CS1000E . CS 1000T is having Euro ISDN PRI with one of the service provider. While making calls from Ip phones registered in 1000T (for test)I can pass on my 4 digits of extension no which in returne is used by the service provider to send the full CLI of the service provider for the DID extension no.

But if a call originated from the IP phones registered in 1000E the same thing is not happenning .

CS1000E capture:
REQ: prt

TYPE: clid

CUST 0

SIZE 8
RNGE


INTL 91

ENTRY 0
HNTN
HLCL
DIDN YES
HLOC 130
LSC
CLASS_FMT DN

=======================
NET_DATA
OPT RTD
AC1 LOC
AC2 INTL NPA SPN NXX
FNP YES
ISDN YES
VPNI 14
PNI 1
PINX_DN
MBG 0
BSGC 65535
PFX1
PFX2
HLOC 130
LSC
RCNT 5
PSTN NO
TNDM 15
PCMC 15
SATD 1
OCLI NO
TIDM NO
DASC
ROPT NRO
DITI YES


PAGE 005

TRNX YES
EXTT NO
FTOP FRES
APAD 0 0
VNR YES
RLI 30
CDPL 4
UDPL 7
NIT 8
NAS_ATCL YES
NAS_ACTV NO
FOPT 14
CNDN
CNAT
PCAT
CNIP YES
DMWM NO
MWNS NO
CNTC
NATC
INTC
====================================
TYPE RDB
CUST 00
ROUT 60
DES PSTN
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS EXT
VTRK YES
ZONE 032
PCID SIP
CRID NO
NODE 308
DTRK NO
ISDN YES
MODE ISLD
DCH 60
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO NO


PAGE 003

FALT NO
CTYP UKWN
INAC YES
ISAR NO
DAPC NO
PTYP ATT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 6060
TCPP NO
TARG
BILN NO
OABS
INST
IDC YES
DCNO 1
NDNO 1 *
DEXT NO
DNAM NO
ANTK
SIGO STD
STYP SDAT
MFC NO
ICIS YES
OGIS YES
PTUT 0
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
EESD 1024
SST 5 0
DTD NO
SCDT NO
2 DT NO
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO


PAGE 004

CDR YES
INC YES
LAST NO
QREC NO
OAL YES
AIA YES
OAN YES
OPD NO
NDP EXC 0
CDRX NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS YES
MRT 40
PANS YES
MANO NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 1
ATAN NO
OHTD NO
PLEV 2
OPR NO
ALRM NO
ART 1
PECL NO
DCTI 0
TIDY 6060 60
ATRR NO
TRRL NO
SGRP 0
ARDN NO
AACR NO

======================================

DES SIP
TN 080 0 08 00 VIRTUAL
TYPE IPTI
CDEN 8D
CUST 0
XTRK VTRK
ZONE 042
LDOP BOP
TIMP 600
BIMP 600
AUTO_BIMP NO
TRK ANLG
NCOS 0
RTMB 69 47
CHID 296
TGAR 1
STRI/STRO WNK WNK
SUPN YES
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD XREP
P10 NTC
TKID
AACR NO
DATE 9 JUN 2007
============================================


Please let me know if any thing else needed to be post.

Many Thanks
DAS1512

 

[johnpoole]

can you trace that call to insure that your not sending, it may be the far end not publishing due to call the call type field

john poole
bellsouth business
columbia,sc

 

[911guru]

It would be better if the originating set composed the full CLID before sending it to the MG 1000T. That way you would not rely on the carrier to do the CLID composition for you.

911Guru

http://pbx-e911.com

 

[56BelAir]

I must admit I am a little confused by the post so if this is of no use to you I will not be affended.

If the 1000E and 1000T are tied together via TIE you may look at RCAP under your D-channel usualy I set to ND2 and this works well for me.

again I am unclear as to what exactly you have or are setting out to do maybe you can clarify and I can resubmit.

 

[RS528]

Change your CLID entry with your HNTN code and your HLCL in your 1000E.

ENTRY 0
HNTN xx
HLCL xxx
DIDN YES
HLOC 130
LSC
CLASS_FMT DN

 

[dlesap]

As RS528 says, apply a CLID entry as it.
In the RLI used by routing, add a DMI which only change CTYP to NPA
In the NRS the routing entry MUST be E164/National

 

[Lynx77]

Configure on CS 1000E Enhanced CLID table in LD 15 for each set/DN.
Set the SPN's CTYP as NPA (national) with a DGT.
On NRS configure the SPN DN prefix as type E-164 National.

Try yhis link on Nortel site:

http://support.nortel.com/go/main.j...te/solutions/398/NORT053559_f.SAL_Public.html