Cisco WS-C4006, one blade status light change to orange!

[JackyZhang]

Hi,
One Cisco WS-C4006 Switch. Recently we bought one WS-4148-RJ45 blade and put into slot 3. the Status of this modeule shows orange, if the computer connect to network through this blade, and there is no problem.

1. We tried this new blade in another WS-C4006 Switch, the status light become green after inistial, so this new blade should be normal
2. We swap two blade in this switch, and only whichever blade you put into slot 3, status light change to orange.
3. We get RMA of the Chassis, and replace chassis, and we got same thing, no change.
4.
5.
....



We also tried:
reset 3
clear config 3
...


It still orange,

 

[BuckWeet]

what does a 'show mod' say?

 

[JackyZhang]

Mod Slot Ports Module-Type Model Sub Status
--- ---- ----- ------------------------- ------------------- --- --------
1 1 2 1000BaseX Supervisor WS-X4013 no ok
2 2 48 Inline Power Module WS-X4148-RJ45V no ok
3 3 48 Inline Power Module WS-X4148-RJ45V no ok
4 4 48 Inline Power Module WS-X4148-RJ45V no ok
5 5 48 Inline Power Module WS-X4148-RJ45V no ok
6 6 48 Inline Power Module WS-X4148-RJ45V no ok

Mod Module-Name Serial-Num
--- -------------------- --------------------
1 JAB05060EPJ
2 JAB050308QQ
3 JAB05340ACZ
4 JAB050405EK
5 JAB050308LX
6 JAB050405HT

Mod MAC-Address(es) Hw Fw Sw
--- -------------------------------------- ------ ---------- -----------------
1 00-05-31-5c-d8-00 to 00-05-31-5c-db-ff 3.1 5.4(1) 7.6(5)
2 00-04-4d-f3-be-40 to 00-04-4d-f3-be-6f 1.5
3 00-05-9a-c0-0f-60 to 00-05-9a-c0-0f-8f 2.7
4 00-04-4d-f3-c7-d0 to 00-04-4d-f3-c7-ff 1.5
5 00-04-4d-f3-b9-30 to 00-04-4d-f3-b9-5f 1.5
6 00-04-4d-f3-d1-60 to 00-04-4d-f3-d1-8f 1.5

 

[Jsteve]

Check to see if you have identical power circuits on both of the 4000.

Also check the environmentals on that 4000. I beleive the command is "sh env power

 

[JackyZhang]

sh env power

Total Inline Power Available: 0 Watt
Total Inline Power Drawn From the System: 0 Watt
Remaining Inline Power in the System: 0 Watt
Configured Default Inline Power allocation per port: 6.00 Watts (0.11 Amps @51V)

Module Total Allocated Max H/W Supported Max H/W Supported
To Module (Watts) Per Module (Watts) Per Port (Watts)
------ ----------------- ------------------ -----------------
2 0.00 0.00 6.500
3 0.00 0.00 6.500
4 0.00 0.00 6.500
5 0.00 0.00 6.500
6 0.00 0.00 6.500

Power Budget is : 2 supplies
Power Available to the System (excluding voice power): 750 Watts (62.50 Amps @12V)
Power Drawn from the System (excluding voice power): 435 Watts (36.25 Amps @12V)
Remaining Power (excluding voice power): 315 Watts (26.25 Amps @12V)

 

[JackyZhang]

I have compared the configuraion of different blade in this switch. And there is no big different, I can not see anything special for Slot 3 and cause the status light change to orange.
Like what I said, I tried to put anohter blade into slot 3, and we got same result.
It is very strange.

 

[JackyZhang]

It has been fixed, I got RMA from Cisco to replace Supervisor, and after that, the status light change to Green