silver1omo
Technical User
Hi,
We have a interconnect between Cisco 3845 and a MD110, the cisco side is emulating the network and the md110 is the user side.
Suddenly the ISDN does not come fully up.
The cisco side shows outgoing SABME but no answer from the pbx.
In the pbx side the guy that manages it says that he sees SABME errors as well.
SAMBE Error in E1
303 DATA LINK ALARM
DATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
02FEB12 19:23:41 2 13 SLP60 004-1-20-00 57 258 7
RDATE RTIME
CLASS: 0
303 DATA LINK ALARM
DATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
13FEB12 21:41:58 3 1 SLP60 003-1-20-00 57 258 0
RDATE RTIME
13FEB12 21:42:05
The cisco config is:
interface Serial0/1/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
What I have of the pbx:
<rocap:rou=17 & 16;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
17 712000000000001 7 3110000010 0 30 128 00141410 211110000030 111111
16 712000000000001 7 3110000010 0 30 128 00141410 211110000030 111111
END
r1= Route =16
r11=route=17
r11 not connected
ROU TYPE VARC VARI VARO FILTER
17 SL60 H'00000310 H'00000000 H'04010000 NO
16 SL60 H'00000310 H'00000000 H'04010000 NO
Could you help me determine if the pbx config is correct for QSIG user side?
We have a interconnect between Cisco 3845 and a MD110, the cisco side is emulating the network and the md110 is the user side.
Suddenly the ISDN does not come fully up.
The cisco side shows outgoing SABME but no answer from the pbx.
In the pbx side the guy that manages it says that he sees SABME errors as well.
SAMBE Error in E1
303 DATA LINK ALARM
DATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
02FEB12 19:23:41 2 13 SLP60 004-1-20-00 57 258 7
RDATE RTIME
CLASS: 0
303 DATA LINK ALARM
DATE TIME ALP NOIF UNIT EQU BRDID INF1 INF2
13FEB12 21:41:58 3 1 SLP60 003-1-20-00 57 258 0
RDATE RTIME
13FEB12 21:42:05
The cisco config is:
interface Serial0/1/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
What I have of the pbx:
<rocap:rou=17 & 16;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
17 712000000000001 7 3110000010 0 30 128 00141410 211110000030 111111
16 712000000000001 7 3110000010 0 30 128 00141410 211110000030 111111
END
r1= Route =16
r11=route=17
r11 not connected
ROU TYPE VARC VARI VARO FILTER
17 SL60 H'00000310 H'00000000 H'04010000 NO
16 SL60 H'00000310 H'00000000 H'04010000 NO
Could you help me determine if the pbx config is correct for QSIG user side?