Cisco router and adsl WIC

[gregworcester]

thanks for the response burtsbees.

I tried your suggestion, nothing.
Begining to suspect that speedstream adsl modem.
I do have a ADSL-WIC card in the router.
Any chance of getting a sample of your config?
Here is my most recent config that does not work.
The only other thing I can think of is maybe I need
client-id on the fa0/0 after dhcp?

ip dhcp excluded-address 192.168.0.2 192.168.0.101
ip dhcp excluded-address 192.168.0.249 192.168.0.254
!
ip dhcp pool whitepine
import all
network 192.168.0.0 255.255.255.0
default-router 192.168.0.101
dns-server 69.24.0.2 69.24.8.2
!
!
interface ATM0/0
mac-address 0007.eb78.10c0
bandwidth 3000
no ip address
no ip redirects
no ip unreachables
ip route-cache flow
shutdown
no atm ilmi-keepalive
atm ilmi-pvc-discovery
dsl operating-mode auto
dsl enable-training-log
!
interface ATM0/0.35 point-to-point
ip address dhcp client-id FastEthernet0/0
no ip redirects
no ip unreachables
ip accounting output-packets
ip nat outside
ip virtual-reassembly
no snmp trap link-status
atm route-bridged ip
pvc 0/35
encapsulation aal5snap
!
interface FastEthernet0/0
ip address dhcp
ip nat outside
ip virtual-reassembly
speed auto
half-duplex
!
interface FastEthernet0/1
ip address 192.168.0.101 255.255.255.0
ip nat inside
ip virtual-reassembly
speed 100
full-duplex
no mop enabled
!
router rip
version 2
network 192.168.0.0
!
ip route 0.0.0.0 0.0.0.0 FastEthernet0/0
!
no ip http server
no ip http secure-server
ip nat inside source list 1 interface FastEthernet0/0 overload
!
access-list 1 permit any

 

[Lemon13]

i might be wrong, but when u shutdown the atm 0/0, isnt the atm subif then also down?

what does show ip interface brief report?

 

[gregworcester]

Thanks for the response lemon13

I have tried to use the wic before, with no success,
so I shut it down to try to get connectivity going
using the adsl modem and the two fa ports with no luck at all so far.
I am going to dump the modem because it does not seem to want to cooperate.
When I have the WIC up I do pull an IP form my ISP,
but have not had any sucess routing it to my lan.
Any advice or tips would be appreciated if you could look my
config over.

 

[brianinms]

At this point are you even sure the circuit works?

 

[gregworcester]

ok got everything hooked up and pinging 4.2.2.2 from a client pc that IS getting an ip from the pool on the router i am getting a destination host unreachable.
Here is some out put from the router with the ADSL WIC card up & up
As you can see I am getting a Showtime from the WIC but cannot get any traffic to the LAN.
Hope this is more usable info than I have posted
previously.

debug atm eve
*Mar 8 00:45:10.551: ATM0/0 dslsar_1a_reset: PLIM type is 18, Rate is 160Mbps
*Mar 8 00:45:10.551: ATM0/0 dslsar_1a_shutdown: state=4
*Mar 8 00:45:10.551: dslsar disable ATM0/0

*Mar 8 00:45:10.551: DSL: SET: [DMTDSL_STOP -> DMTDSL_INIT]
*Mar 8 00:45:10.551: Resetting ATM0/0
*Mar 8 00:45:10.555: dslsar_1a_config(ATM0/0)
*Mar 8 00:45:10.555: dslsar_1a_enable(ATM0/0)
*Mar 8 00:45:10.559: ATM0/0: dslsar_init
*Mar 8 00:45:10.567: ATM0/0:check_lockup: scc = 0 output_qcount = 0,heads)3, 0,
addr = (s)0x0, 0x0, count (s)3, 3
*Mar 8 00:45:10.567: ATM0/0:check_lockup: scc = 1 output_qcount = 0,heads)10, 1,
addr = (s)0x0, 0x82E1DFD4, count (s)86, 102
*Mar 8 00:45:10.567: ATM0/0 dslsar_MatchSARTxToLineSpeed(): usbw 160, clkPerCell 93624 prev_clkPerCell 9702
*Mar 8 00:45:10.571: ATM0/0 dslsar_MatchSARTxToLineSpeed(): Changing line speed from fast to slow
*Mar 8 00:45:10.679: ATM0/0 dslsar_update_us_bandwidth(): upstream bw =160 Kbps
*Mar 8 00:45:11.179: (ATM0/0)1a_enable: delay activation of vcd=1, vc=0x8362122C
*Mar 8 00:45:11.191: DSL: SM: [DMTDSL_STOP -> DMTDSL_INIT]
*Mar 8 00:45:11.195: DSL: SM: [DMTDSL_INIT -> DMTDSL_DLOAD_1]
*Mar 8 00:45:11.199: DSL: Downloading ASW_init_3_8_131.bin
*Mar 8 00:45:11.211: DSLATM0/0) Downloaded 5 blocks... Finished!
*Mar 8 00:45:11.211: DSL(ATM0/0): Sent command 0x14
*Mar 8 00:45:12.551: %LINK-3-UPDOWN: Interface ATM0/0, changed state to down
*Mar 8 00:45:12.551: dslsar_atm_lineaction(ATM0/0): state=0
*Mar 8 00:45:15.123: DSL: Received response: 0x80
*Mar 8 00:45:15.123: DSL: SM: [DMTDSL_DLOAD_1 -> DMTDSL_DLOAD_2]
*Mar 8 00:45:15.531: DSL: Downloading ASW_R3_8_131.bin
*Mar 8 00:45:15.771: DSL(ATM0/0): Downloaded 100 blocks
*Mar 8 00:45:16.003: DSL(ATM0/0): Downloaded 200 blocks
*Mar 8 00:45:16.239: DSL(ATM0/0): Downloaded 300 blocks
*Mar 8 00:45:16.471: DSL(ATM0/0): Downloaded 400 blocks
*Mar 8 00:45:16.731: DSL(ATM0/0): Downloaded 500 blocks
*Mar 8 00:45:16.967: DSL(ATM0/0): Downloaded 600 blocks
*Mar 8 00:45:17.199: DSL(ATM0/0): Downloaded 700 blocks
*Mar 8 00:45:17.431: DSL(ATM0/0): Downloaded 800 blocks
*Mar 8 00:45:17.687: DSL(ATM0/0): Downloaded 900 blocks
*Mar 8 00:45:17.919: DSL(ATM0/0): Downloaded 1000 blocks
*Mar 8 00:45:18.203: DSL(ATM0/0): Downloaded 1100 blocks
*Mar 8 00:45:18.439: DSL(ATM0/0): Downloaded 1200 blocks
*Mar 8 00:45:18.695: DSL(ATM0/0): Downloaded 1300 blocks
*Mar 8 00:45:18.731: DSLATM0/0) Downloaded 1317 blocks... Finished!
*Mar 8 00:45:18.731: DSL(ATM0/0): Sent command 0x14
*Mar 8 00:45:20.739: set tx_gain_offset to 0
*Mar 8 00:45:20.739: set rx_gain_offset to 0
*Mar 8 00:45:20.743: set target_noise_margin_offset to 0
*Mar 8 00:45:20.743: set max_bits_tone_limit to 14
*Mar 8 00:45:20.743: changed current state to do open!!
*Mar 8 00:45:20.743: DSL: SM: [DMTDSL_DLOAD_2 -> DMTDSL_DO_OPEN]
*Mar 8 00:45:20.743: DSL: Send ADSL_OPEN command.
*Mar 8 00:45:20.743: DSL(ATM0/0): Using subfunction 0x15
*Mar 8 00:45:20.747: LOCAL:Max noise margin for power cutoff 31
*Mar 8 00:45:20.747: DSL(ATM0/0): Sent command 0x3
*Mar 8 00:45:23.247: DSL(ATM0/0): 1: Modem state = 0x8
*Mar 8 00:45:25.747: DSL(ATM0/0): 2: Modem state = 0x8
*Mar 8 00:45:28.247: DSL(ATM0/0): 3: Modem state = 0x10
*Mar 8 00:45:30.747: DSL(ATM0/0): 4: Modem state = 0x10
*Mar 8 00:45:33.247: DSL(ATM0/0): 5: Modem state = 0x10
*Mar 8 00:45:35.747: DSL(ATM0/0): 6: Modem state = 0x10
*Mar 8 00:45:35.863: DSL: Received response: 0x24
*Mar 8 00:45:35.863: DSL: Showtime!
*Mar 8 00:45:35.867: DSL(ATM0/0): Sent command 0x11
*Mar 8 00:45:35.867: DSL: Received response: 0x61
*Mar 8 00:45:35.871: DSL: Read firmware revision 0x1A04
*Mar 8 00:45:35.871: DSL(ATM0/0): Sent command 0x31
*Mar 8 00:45:35.875: DSL: Received response: 0x12
*Mar 8 00:45:35.875: DSL(ATM0/0): operation mode 0x0002
*Mar 8 00:45:35.875: DSL(ATM0/0): Sent command 0x33
*Mar 8 00:45:35.879: DSL: Received response: 0x16
*Mar 8 00:45:35.879: DSL(ATM0/0): Far End ITU Country Code 0x0F
*Mar 8 00:45:35.879: DSL: Far End ITU Vendor ID ALCB
*Mar 8 00:45:35.879: DSL: Far End ITU Vendor ID Specific 0x0000
*Mar 8 00:45:35.883: DSL: Far End ITU Vendor STD Number 0x0001
*Mar 8 00:45:35.883: DSL(ATM0/0): Sent command 0x32
*Mar 8 00:45:35.883: DSL: Received response: 0x14
*Mar 8 00:45:35.883: DSL(ATM0/0): Near End ITU Country Code 0x00
*Mar 8 00:45:35.887: DSL: Near End ITU Vendor ID ALCB
*Mar 8 00:45:35.887: DSL: Near End ITU Vendor ID Specific 0x0000
*Mar 8 00:45:35.887: DSL: Near End ITU Vendor STD Number 0x0001
*Mar 8 00:45:35.887: ATM0/0 dslsar_MatchSARTxToLineSpeed(): usbw 160, clkPerCell 93624 prev_clkPerCell 93624
*Mar 8 00:45:35.887: ATM0/0 dslsar_update_us_bandwidth(): upstream bw =160 Kbps
*Mar 8 00:45:35.887: DSL: Reading training log
*Mar 8 00:45:35.887: DSL(ATM0/0): Sent command 0x16
*Mar 8 00:45:38.387: DSL: Received 1 timer events during MODEM_GET_ADDRESS
*Mar 8 00:45:40.887: DSL: Received 2 timer events during MODEM_GET_ADDRESS
*Mar 8 00:45:43.387: DSL: Received 3 timer events during MODEM_GET_ADDRESS
*Mar 8 00:45:45.887: DSL: No response for MODEM_GET_ADDRESS
*Mar 8 00:45:45.891: DSL(ATM0/0): training log start address 0x786B6
*Mar 8 00:45:45.891: DSL(ATM0/0): Sent command 0x16
*Mar 8 00:45:48.391: DSL: Received 1 timer events during MODEM_GET_ADDRESS
*Mar 8 00:45:50.891: DSL: Received 2 timer events during MODEM_GET_ADDRESS
*Mar 8 00:45:53.391: DSL: Received 3 timer events during MODEM_GET_ADDRESSint atm0/0
*Mar 8 00:45:55.891: DSL: No response for MODEM_GET_ADDRESS
*Mar 8 00:45:55.891: DSL(ATM0/0): training log end addreend

WP2621#debug atm pac
ATM packets debugging is on
Displaying all ATM packets
WP2621#
*Mar 8 00:39:39.971: ATM0/0 RX(82AD4FB8), size 404 [
*Mar 8 00:39:39.971: ATM0/0.35(I):
VCD:0x1 VPI:0x0 VCI:0x23 Type:0x0 SAP:AAAA CTL:03 OUI:0080C2 TYPE:0007 Length:0x164
*Mar 8 00:39:39.971: 0000 FFFF FFFF FFFF 0001 9626 8594 0800 4500 0148 BBFB 0000 FE11 473C D86B
*Mar 8 00:39:39.975: E001 FFFF FFFF 0043 0044 0134 AF82 0201 0600 97CF 475D 0000 0000 D86B E0D0
*Mar 8 00:39:39.979: D86B E0D0 D86B E001 0000 0000 000F CC20 7E76 0000 0000 0000 0000 0000 0000
*Mar 8 00:39:39.983: 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
*Mar 8 00:39:39.983: 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
*Mar 8 00:39:39.987: 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
*Mar 8 00:39:39.991: 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
*Mar 8 00:39:39.995: 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000


WP2621#sh ip rou
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

C 192.168.0.0/24 is directly connected, FastEthernet0/1
S* 0.0.0.0/0 is directly connected, FastEthernet0/0
C 216.107.224.0/23 is directly connected, ATM0/0.35


WP2621#sh ip pro
Routing Protocol is "rip"
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Sending updates every 30 seconds, next due in 13 seconds
Invalid after 180 seconds, hold down 180, flushed after 240
Redistributing: rip
Default version control: send version 2, receive version 2
Interface Send Recv Triggered RIP Key-chain
FastEthernet0/1 2 2
Automatic network summarization is in effect
Maximum path: 4
Routing for Networks:
192.168.0.0
Routing Information Sources:
Gateway Distance Last Update
Distance: (default is 120)
*Mar 8 00:34:41.979: dslsar_init_txring_params: default tx-ring setting is selected for vpi/vci = 0/35
*Mar 8 00:34:41.979: ATM0/0:dslsar_init_tx_chan_desc_per_vc, vcd = 1, addr = 0x00011040, size = 64
*Mar 8 00:34:41.979: ATM0/0 dslsar_vc_setup: vcd 1
*Mar 8 00:34:41.983: CONFIGURING(ATM0/0) VC 1 (0/35) IN TX SCHEDULE TABLE SET 1
*Mar 8 00:34:41.983: (ATM0/0)Forcing Peakrate and Avgrate to: 160
*Mar 8 00:34:41.983: (ATM0/0)Requested QoS: Peakrate = 160, Avgrate = 160, Burstsize =0
*Mar 8 00:34:41.983: (ATM0/0)Configuring VC 1: slot 0 in TST 5
*Mar 8 00:34:41.983: (ATM0/0) SUCCESSFUL CONFIGURATION OF VC 1 (0/35), QOS Type 4
*Mar 8 00:34:41.983: dslsar_setup_cos(ATM0/0): vc:1 wred_name:- max_q:0
*Mar 8 00:34:41.987: ATM0/0: vcd = 1, max_tx_time = 13410
*Mar 8 00:34:41.987: ATM0/0:check_lockup: scc = 0 output_qcount = 0,heads)0, 0,
addr = (s)0x0, 0x0, count (s)0, 0
*Mar 8 00:34:41.991: ATM0/0:check_lockup: scc = 1 output_qcount = 0,heads)10, 7,
addr = (s)0x82E29A28, 0x82E29DAC, count (s)67, 86


WP2621#debug ip pack
IP packet debugging is on
WP2621#
*Mar 8 00:35:52.147: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:35:53.451: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:35:55.455: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:35:56.951: IP: s=216.107.224.1 (ATM0/0.35), d=255.255.255.255, len 328, rcvd 2
*Mar 8 00:35:57.459: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:35:58.467: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:36:00.467: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:36:02.471: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:36:04.475: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:36:06.479: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:36:06.787: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:36:08.487: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:36:10.487: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:36:10.811: IP: s=216.107.224.1 (ATM0/0.35), d=255.255.255.255, len 328, rcvd 2
*Mar 8 00:36:12.495: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:36:14.495: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB
*Mar 8 00:36:16.499: IP: tableid=0, s=192.168.0.101 (local), d=192.168.0.50 (FastEthernet0/1), routed via FIB

 

[brianinms]

Can you ping 4.2.2.2 from the router?

 

[gregworcester]

yes

 

[brianinms]

Add this to the router configuration


router(config)#ip routing


and then try to ping 4.2.2.2 from the pc

 

[gregworcester]

Now i cant ping anything
Man this is weird, from the look of this config
i should be routing!

ip dhcp excluded-address 192.168.0.2 192.168.0.101
ip dhcp excluded-address 192.168.0.249 192.168.0.254
!
ip dhcp pool whitepine
import all
network 192.168.0.0 255.255.255.0
default-router 192.168.0.101
dns-server 69.24.0.2 69.24.8.2
!
interface ATM0/0
mac-address 0007.eb78.10c0
bandwidth 3000
no ip address
no ip redirects
no ip unreachables
ip route-cache flow
no atm ilmi-keepalive
atm ilmi-pvc-discovery
dsl operating-mode auto
dsl enable-training-log
!
interface ATM0/0.35 point-to-point
ip address dhcp client-id FastEthernet0/0
no ip redirects
no ip unreachables
ip accounting output-packets
ip nat outside
ip virtual-reassembly
no snmp trap link-status
atm route-bridged ip
pvc 0/35
encapsulation aal5snap
!
!
interface FastEthernet0/0
ip address dhcp
ip nat outside
ip virtual-reassembly
speed auto
half-duplex
!
interface FastEthernet0/1
ip address 192.168.0.101 255.255.255.0
ip nat inside
ip virtual-reassembly
speed 100
full-duplex
no mop enabled
!
router rip
version 2
network 192.168.0.0
!
ip route 0.0.0.0 0.0.0.0 FastEthernet0/0
!
no ip http server
no ip http secure-server
ip nat inside source list 1 interface FastEthernet0/0 overload
!
access-list 1 permit any

 

[Minue]

Hello
You will have to update your default route:
ip route 0.0.0.0 0.0.0.0 ATM0/0.35

If thing doesn't work after the update.As mention before in a former post please post a "Show ip nat translation"after ping from the PC.If you can ping from the router your'e getting close.Also try to find out your next hop router (ISP gateway).This can be done with a traceroute.And use this in your default route instead of the ATM interface.

Regards

 

[gregworcester]

Minue
I know the next hop to the ISP
How would I apply it?
In my IP nat staement?

 

[gregworcester]

I used the ip route with my ISP gateway and got this.
At the end it actually recognized my routers hostname,
atm sub interface gave me an address.
I was able to ping 4.2.2.2 from the router, but still destination unreachable from a client. I am getting really
close to this now I think, but just need to get it into the lan.

*Mar 8 04:47:42.342: ATM0/0: dslsar_bringup_interface: Interface and atm_db flags are UP
*Mar 8 04:47:44.342: %LINK-3-UPDOWN: Interface ATM0/0, changed state to up
*Mar 8 04:47:44.342: dslsar_atm_lineaction(ATM0/0): state=4
*Mar 8 04:47:45.342: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0, changed state to up
*Mar 8 04:47:50.510: dslssar_init_tcq: Initializing TCQ
*Mar 8 04:47:50.510: dslsar_init_txring_params: default tx-ring setting is selected for vpi/vci = 0/35
*Mar 8 04:47:50.510: ATM0/0:dslsar_init_tx_chan_desc_per_vc, vcd = 1, addr = 0x00011040, size = 64
*Mar 8 04:47:50.510: ATM0/0 dslsar_vc_setup: vcd 1
*Mar 8 04:47:50.514: CONFIGURING(ATM0/0) VC 1 (0/35) IN TX SCHEDULE TABLE SET 1
*Mar 8 04:47:50.514: (ATM0/0)Forcing Peakrate and Avgrate to: 160
*Mar 8 04:47:50.514: (ATM0/0)Requested QoS: Peakrate = 160, Avgrate = 160, Burstsize =0
*Mar 8 04:47:50.514: (ATM0/0)Configuring VC 1: slot 0 in TST 5
*Mar 8 04:47:50.514: (ATM0/0) SUCCESSFUL CONFIGURATION OF VC 1 (0/35), QOS Type 4
*Mar 8 04:47:50.514: dslsar_setup_cos(ATM0/0): vc:1 wred_name:- max_q:0
*Mar 8 04:47:50.514: ATM0/0: vcd = 1, max_tx_time = 13410
*Mar 8 04:47:50.518: ATM0/0:check_lockup: scc = 0 output_qcount = 0,heads)0, 0,
addr = (s)0x0, 0x0, count (s)8, 8
*Mar 8 04:47:50.518: ATM0/0:check_lockup: scc = 1 output_qcount = 0,heads)15, 6,
addr = (s)0x8340C450, 0x82E296A4, count (s)268, 297
*Mar 8 04:47:56.718: %DHCP-6-ADDRESS_ASSIGN: Interface ATM0/0.35 assigned DHCP address 216.107.225.239, mask 255.255.254.0, hostname WP2621

 

[Minue]

Can you please post the "Show ip nat translation" and also your updated conf.Make sure you have the 2 updated lines:

ip nat inside source list 1 interface ATM0/0.35 overload

ip route 0.0.0.0 0.0.0.0 ATM0/0.35
OR
ip route 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx = ISP GATEWAY

Regards

 

[gregworcester]

I think I am getting closer
step by step, inch by inch
I can ping anything on the router
i can ping 4.2.2.2 on a client,
but that is it.
As vou can see in my conf I changed my dns to
the .101 in the pool and dumped the 206... name-servers
in favor of the 69...'s


ip dhcp pool whitepine
import all
network 192.168.0.0 255.255.255.0
default-router 192.168.0.101
dns-server 69.24.0.2 69.24.8.2
!
interface ATM0/0
mac-address 0007.eb78.10c0
bandwidth 3000
no ip address
no ip redirects
no ip unreachables
ip route-cache flow
no atm ilmi-keepalive
atm ilmi-pvc-discovery
dsl operating-mode auto
dsl enable-training-log
!
interface ATM0/0.35 point-to-point
ip address dhcp client-id FastEthernet0/0
no ip redirects
no ip unreachables
ip accounting output-packets
ip nat outside
ip virtual-reassembly
no snmp trap link-status
atm route-bridged ip
pvc 0/35
encapsulation aal5snap
!
!
interface FastEthernet0/0
ip address dhcp
ip nat outside
ip virtual-reassembly
speed auto
half-duplex
!
interface FastEthernet0/1
ip address 192.168.0.101 255.255.255.0
ip nat inside
ip virtual-reassembly
speed 100
full-duplex
no mop enabled
!
router rip
version 2
network 192.168.0.0
!
ip route 0.0.0.0 0.0.0.0 216.107.224.1
!
no ip http server
no ip http secure-server
ip nat inside source list 1 interface ATM0/0.35 overload
!
access-list 1 permit any
!



WP2621#sh ip nat translations
Pro Inside global Inside local Outside local Outside global
icmp 216.107.225.249:35 216.107.225.249:35 4.2.2.2:35 4.2.2.2:35
icmp 216.107.225.249:36 216.107.225.249:36 209.85.171.100:36 209.85.171.100:36
icmp 216.107.225.249:37 216.107.225.249:37 209.85.171.100:37 209.85.171.100:37
icmp 216.107.225.249:38 216.107.225.249:38 209.85.171.100:38 209.85.171.100:38
icmp 216.107.225.249:39 216.107.225.249:39 209.85.171.100:39 209.85.171.100:39
icmp 216.107.225.249:40 216.107.225.249:40 209.85.171.100:40 209.85.171.100:40
icmp 216.107.225.249:41 216.107.225.249:41 4.2.2.2:41 4.2.2.2:41
icmp 216.107.225.249:42 216.107.225.249:42 209.85.171.100:42 209.85.171.100:42
icmp 216.107.225.249:43 216.107.225.249:43 209.85.171.100:43 209.85.171.100:43
udp 216.107.225.249:49635 216.107.225.249:49635 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:49972 216.107.225.249:49972 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:50171 216.107.225.249:50171 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:50739 216.107.225.249:50739 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:50811 216.107.225.249:50811 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:50884 216.107.225.249:50884 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:50953 216.107.225.249:50953 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:51028 216.107.225.249:51028 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:51074 216.107.225.249:51074 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:51157 216.107.225.249:51157 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:51340 216.107.225.249:51340 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:51578 216.107.225.249:51578 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:51980 216.107.225.249:51980 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:52980 216.107.225.249:52980 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:53514 216.107.225.249:53514 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:53662 216.107.225.249:53662 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:53824 216.107.225.249:53824 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:54007 216.107.225.249:54007 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:54115 216.107.225.249:54115 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:54205 216.107.225.249:54205 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:54221 216.107.225.249:54221 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:54242 216.107.225.249:54242 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:54440 216.107.225.249:54440 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:54465 216.107.225.249:54465 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:54564 216.107.225.249:54564 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:54585 216.107.225.249:54585 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:54605 216.107.225.249:54605 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:54759 216.107.225.249:54759 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:54928 216.107.225.249:54928 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:55269 216.107.225.249:55269 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:55665 216.107.225.249:55665 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:56084 216.107.225.249:56084 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:56559 216.107.225.249:56559 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:56939 216.107.225.249:56939 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:57223 216.107.225.249:57223 69.24.8.2:53 69.24.8.2:53
udp 216.107.225.249:57260 216.107.225.249:57260 69.24.0.2:53 69.24.0.2:53
udp 216.107.225.249:57452 216.107.225.249:57452 69.24.0.2:53 69.24.0.2:53
--More--
!

 

[Minue]

Thats cool!Try to ping

http://www.google.com

from the PC to see if it can resolves names.Also use nslookup to see which DNS server the PC is using.On the router I would take out either the "import all" or dns-server command.The DHCP pool doesn't need both,could cause conflict.Note that "import all" is more reliable because it will pass on the ISP DNS servers.You can also try the 4.2.2.2 as a DNS server it's quit reliable.
Regards

 

[Minue]

Hello
If the above fails.And your ISP is really using PPPoE.Check this post out:

http://www.tek-tips.com/viewthread.cfm?qid=1528220&page=2

Regards

 

[silverhairb]

CHAP/PAP?

[the other] Bill

 

[gregworcester]

Ok, this should be working.
I can ping google and 4.2.2.2 from the router.
I can ping 4.2.2.2 but not google from a client.
My nat translations appear to be working.
No access lists in place. Could this be it?
The WIC card sees my router hostname, and gives me an IP.
I am running the RIP protocol.
Here is my most recent config.




hostname WP2621
!
boot-start-marker
boot-end-marker
!
no logging console
enable secret 5 $1$Dy8Z$7oI5JBnvmSCMeerU05/E0/
enable password 7 105D0C170216
!
no aaa new-model
!
resource policy
!
ip cef
!
!
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.0.2 192.168.0.101
ip dhcp excluded-address 192.168.0.249 192.168.0.254
!
ip dhcp pool whitepine
network 192.168.0.0 255.255.255.0
default-router 192.168.0.101
dns-server 69.24.0.2 69.24.8.2
domain-name seg.net
!
!
ip name-server 192.168.0.101
!
!
!
!
!
!
!
!
!
interface ATM0/0
mac-address 0007.eb78.10c0
bandwidth 3000
no ip address
no ip redirects
no ip unreachables
ip route-cache flow
no atm ilmi-keepalive
atm ilmi-pvc-discovery
dsl operating-mode auto
dsl enable-training-log
!
interface ATM0/0.35 point-to-point
ip address dhcp client-id FastEthernet0/0
no ip redirects
no ip unreachables
ip accounting output-packets
ip nat outside
ip virtual-reassembly
no snmp trap link-status
atm route-bridged ip
pvc 0/35
encapsulation aal5snap
!
!
interface FastEthernet0/0
ip address dhcp
ip nat outside
ip virtual-reassembly
speed auto
half-duplex
!
interface FastEthernet0/1
ip address 192.168.0.101 255.255.255.0
ip nat inside
ip virtual-reassembly
speed 100
full-duplex
no mop enabled
!
router rip
version 2
network 192.168.0.0
!
ip route 0.0.0.0 0.0.0.0 216.107.224.1
!
no ip http server
no ip http secure-server
ip nat inside source list 1 interface ATM0/0.35 overload
!
access-list 1 permit 192.168.1.0 0.0.0.255

 

[Minue]

Hello
Do you really need help?It's seems like your'e ignoring my post.If you don't give good feedback all is worthless.
Have you done the DNS tests on the PC,if so what results did you get.
You should keep things simple for now.Get rid of RIP and hook the PC directly to the NAT router.Put back in the access-list that will allow the local subnet to be NAT.Allowing all subnet is OK for troubleshooting.

access-list 1 permit any
OR
access-list 1 permit 192.168.0. 0.0.0.255

Did this Internet connection new,was a working with the your ADSL modem?

Regards

 

[gregworcester]

I gave up on the modem
Working with the WIC card now.
Should I hook a dedicated PC to the WAN
or LAN side.