Cisco ATA phone ports as Co Trunk

[AvayaArmy]

Hello, I'm trying to create a trunk group with CO trunks from Cisco ATA ports (see below). When I try to dial using that tac from 64xx telset, it goes blank after I dial certain numbers. I get the alarm and error like shown below. I'm lost please help.


display trunk-group 18 Page 1 of 10
TRUNK GROUP
Group Number: 18 Group Type: co CDR Reports: y
Group Name: Incall>KWT GSM COR: 1 TN: 1 TAC: 818
Direction: outgoing Outgoing Display? n
Dial Access? n Busy Threshold: 99
Queue Length: 0 Country: 17
Comm Type: voice Digit Absorption List:
Prefix-1? n Trunk Flash? n Toll Restricted? n
TRUNK PARAMETERS
Trunk Type: loop-start
Outgoing Dial Type: tone Cut-Through? n
Trunk Termination: rc Disconnect Timing(msec): 900
Auto Guard? n Call Still Held? n Sig Bit Inversion: none
Analog Loss Group: 6 Digital Loss Group: 11
Trunk Gain: high
Disconnect Supervision - Out? n
Answer Supervision Timeout: 10 Receive Answer Supervision? n

display trunk-group 18
display trunk-group 18 Page 2 of 10
TRUNK FEATURES
ACA Assignment? n Measured: external
Maintenance Tests? y
Data Restriction? n
Suppress # Outpulsing? y
Charge Conversion: 1
Decimal Point: none
Currency Symbol:
Charge Type: units
Per Call CPN Blocking Code:
Per Call CPN Unblocking Code:
Outgoing ANI:


display trunk-group 18
display trunk-group 18 Page 3 of 10
ADMINISTRABLE TIMERS
Send Incoming/Outgoing Disconnect Timers to TN465 Ports? n
Outgoing Disconnect(msec): 500
Outgoing Dial Guard(msec): 1600
Outgoing Glare Guard(msec): 1500
Ringing Monitor(msec): 5200 Incoming Seizure(msec): 250
Outgoing End of Dial(sec): 10 Outgoing Seizure Response(sec): 3
Programmed Dial Pause(msec): 1500
Flash Length(msec): 600
END TO END SIGNALING
Tone(msec): 350 Pause(msec): 150
OUTPULSING INFORMATION
PPS: 10 Make(msec): 40 Break(msec): 60 PPM? n


display trunk-group 18
display trunk-group 18 Page 4 of 10
TRUNK GROUP
Administered Members (min/max): 1/1
GROUP MEMBER ASSIGNMENTS Total Administered Members: 1
Port Code Sfx Name Mode Type Ans Delay
1: 01B0802 TN465 C
2:
3:
4:
5:
6:
7:
8:
9:
10:
11:
12:
13:
14:
15:
-----------------------------------
Alarm
01B0802 CO-TRK n 18/01 WARNING RDY 05/06/12:12 00/00/00:00
01B0802 CO-TRK n 18/01 WARNING RDY 05/06/12:12 00/00/00:00
---------------------------------

Error
01B0802 CO-TRK 18/01 3585 57424 05/06/12:11 05/06/18:16 30 4 4 a y
01B0802 CO-TRK 18/01 1537 05/06/12:11 05/06/18:16 30 4 4 a y

 

[1a22ip]

First change dial access to Y. Also status the trunk to see if the member comes in service/idle.

Hope this helps
ED

1a2 to ip I seen it all

 

[AvayaArmy]

Oops... I'm sorry I've done it already.. After I change dial-access to "y" only all these things happened.

 

[1a22ip]

Are you sure that the trunks are loop start. I would have thought they be immed/immed.

Hey it's worth a try
ED

1a2 to ip I seen it all

 

[AvayaArmy]

Yes I'm sure, it's loop start... what am I missing..? someone pls help.

 

[RTMCKEE]

Do the ATAs provide dialtone? seems like when I was hooking some of these up for faxes there was something funky with them. Can you put a buttset between the switch and ATA to listen to see if you get the dialtone when the switch opens up the port?

RTMCKEE

CM 2.1.1
Prologix R9.05
Modular Messaging 1.1