Cisco 876W with connection to D-Link

[Nazgulero]

Hello all,

I am having trouble getting Internet connectivity for my clients on a 876W Cisco. My setup is this:

Wired/Wireless Clients --> Cisco 876W --> D-Link AP2200 --> D-Link AP2200 --> Cable Modem --> Internet

So, there are wired and wireless clients connected to the 876 router. Connectivity for the wired clients is ok, but the wireless clients can only get as far as their default gateway. I am posting the configuration of the 876, maybe somebody can spot something ?

Using 3022 out of 131072 bytes
!
version 12.3
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
!
hostname 876W
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 debugging
logging console critical
!
clock timezone PCTime 2
clock summer-time PCTime date Mar 30 2003 3:00 Oct 26 2003 4:00
no aaa new-model
ip subnet-zero
no ip source-route
ip cef
!
!
ip tcp synwait-time 10
no ip bootp server
ip domain name yourdomain.com
ip ssh time-out 60
ip ssh authentication-retries 2
no ftp-server write-enable
!
!
!
!
!
bridge irb
!
!
interface BRI0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
shutdown
no cdp enable
!
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
shutdown
no atm ilmi-keepalive
dsl operating-mode auto
!
interface FastEthernet0
no ip address
no cdp enable
!
interface FastEthernet1
no ip address
no cdp enable
!
interface FastEthernet2
no ip address
no cdp enable
!
interface FastEthernet3
no ip address
no cdp enable
!
interface Dot11Radio0
no ip address
!
ssid OFFICENET
vlan 1
authentication open
!
ssid ciscowep
vlan 2
authentication open
!
speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2437
station-role root
no cdp enable
!
interface Dot11Radio0.2
encapsulation dot1Q 2
no cdp enable
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 spanning-disabled
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
!
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$FW_INSIDE$
no ip address
bridge-group 1
bridge-group 1 spanning-disabled
!
interface Vlan2
no ip address
bridge-group 2
bridge-group 2 spanning-disabled
!
interface BVI1
ip address 192.168.1.1 255.255.255.0
!
interface BVI2
ip address 192.168.2.1 255.255.255.0
!
ip classless
!
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 5 life 86400 requests 10000
!
logging trap debugging
no cdp run
route-map ON_Route permit 10
match ip address 1
!
!
control-plane
!
bridge 1 route ip
bridge 2 route ip
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
!
line con 0
login local
no modem enable
transport preferred all
transport output telnet
line aux 0
login local
transport preferred all
transport output telnet
line vty 0 4
privilege level 15
login local
transport preferred all
transport input telnet ssh
transport output all
!
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end

Thanks in advance for all your help !

Naz