CatOS to IOS HELP!!!!!!!!!!!! 1

[smoyer90]

I just purchased 4506-E my old 6500 has catOS. how can I convert this command to IOS?

Thanks-Steven


set vtp domain xxxxxx
set vtp mode transparent
set vlan 1 name default type ethernet mtu 1500 said 100001 state active
set vlan xxx name xxxxx type ethernet mtu 1500 said 100507 state active
set vlan xxx name xxxxx type ethernet mtu 1500 said 100742 state active
set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active
set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state active stp ieee
set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active stp ibm
set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state active mode srb aremaxhop 7 stemaxhop 7 backupcrf of
!
#ip
set interface sc0 1 xx.xxx.xxx.xx/xxx.xxx.xxx.x xx.xxx.xxx.xxx

set interface sc1 0 0.0.0.0/0.0.0.0 0.0.0.0

set interface sc1 down
set ip route 0.0.0.0/0.0.0.0 xx.xxx.xxx.x
set ip alias default 0.0.0.0
!
#spantree
#vlan <VlanId>
set spantree priority 1 1
!
#syslog
set logging server enable
set logging server xx.xxx.x.xxx
set logging level ethc 2 default
set logging level gl2pt 2 default
set logging server severity 6
!
#set boot command
set boot config-register 0x2102
set boot system flash slot0:cat6000-supk8.7-6-3a.bin
set boot system flash bootflash:cat6000-supk8.7-6-3a.bin
!
#qos
set qos enable
set qos wrr 2q2t 5 255
set qos wrr 1p2q2t 5 255
set qos wred 1p2q2t tx queue 1 40:80 70:100
set qos wred 1p2q2t tx queue 2 40:80 70:100
set qos wrr 1p2q1t 5 255
!
# default port status is enable
!
!
#module 1 : 2-port 1000BaseX Supervisor
set vlan xxx 1/1
set cdp disable 1/1
set trunk 1/2 on dot1q 1-1005,1025-4094
set spantree portfast 1/1-2 disable
set spantree guard none 1/1-2
!
#module 2 : 8-port 1000BaseX Ethernet
set spantree portfast 2/1-8 disable
set spantree guard none 2/1-8
!
#module 3 empty
!
#module 4 empty
!
#module 5 empty
!

 

[lerdalt]

My catOS is rusty, but here is most of what I think you are looking for:
set vtp domain xxxxxx = vtp domain xxxxxx
set vtp mode transparent = vtp mode transparent
set vlan 1 name default type ethernet mtu 1500 said 100001 state active = vlan xxx name xxxxx
set vlan xxx name xxxxx type ethernet mtu 1500 said 100507 state active = vlan xxx state active
set vlan xxx name xxxxx type ethernet mtu 1500 said 100742 state active
!
#ip
set interface sc0 1 xx.xxx.xxx.xx/xxx.xxx.xxx.x xx.xxx.xxx.xxx


Hope this helps.

set ip route 0.0.0.0/0.0.0.0 xx.xxx.xxx.x = ip route 0.0.0.0 0.0.0.0 xx.xxx.xxx.x
!
set spantree priority 1 1 = spanning-tree vlan 1 priority 1
!
#syslog
set logging server enable
set logging server xx.xxx.x.xxx = logging xx.xxx.x.xxx
set logging level ethc 2 default = logging source-interface xxxxx
set logging level gl2pt 2 default
set logging server severity 6 = logging buffered ? (I think this is what you are looking for)
!

I'm going to let someone else answer the QoS lines for you. As for interfaces, couple things you can do. First is an interface range command:
interface range gig 1/1 - 2
Will configure all interfaces in that range, then do various configuration tasks under the group.
Second is per interface:
interface gig 1/1

You will probably want to use a mix of the 2.
For the interface configs, here you go:
set vlan xxx 1/1 = switchport access vlan xxx
set cdp disable 1/1 = cdp disable
set trunk 1/2 on dot1q 1-1005,1025-4094 = switchport mode trunk (may have to set encapsulation)
set spantree portfast 1/1-2 disable = spanning-tree portfast disable (will probably have to globally set spanning-tree portfast
set spantree guard none 1/1-2 = spanning-tree guardroot disable