Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Cant send/receive fax to remote site on PRI 2

Status
Not open for further replies.

mjoetech

Technical User
Sep 12, 2007
183
US
Hi,

I have an s8700, CM 5.2 with a remote (LSP) site in Bosten that cant send or receive faxes off their local PRI. I have local analog CO trunks (for backup)that I can termporarily point to the faxes and they then work. However, when I send faxes to the PRI's DID number, the fax machine answered but errors out. The fax machine was swapped out with the same results.

The LEC says it is not a compressed trunk and should send faxes fine. All voice calls are fine and no errors on the DS1. The trunk group is as follows.

TRUNK GROUP

Group Number: 20 Group Type: isdn CDR Reports: y
Group Name: Boston Pri COR: 1 TN: 1 TAC: 820
Direction: two-way Outgoing Display? n Carrier Medium: PRI/BRI
Dial Access? n Busy Threshold: 255 Night Service:
Queue Length: 0
Service Type: public-ntwrk Auth Code? n TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4

Group Type: isdn

TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): enbloc/enbloc

Trunk Hunt: descend
Digital Loss Group: 13
Incoming Calling Number - Delete: Insert: Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0
Administer Timers? n CONNECT Reliable When Call Leaves ISDN? n



SIGNALING GROUP

Group Number: 20 Group Type: isdn-pri
Associated Signaling? y Max number of NCA TSC: 2
Primary D-Channel: 002V224 Max number of CA TSC: 2
Trunk Group for NCA TSC:
Trunk Group for Channel Selection: 20
TSC Supplementary Service Protocol: a



Does anyone have any idea what can cause this?

Thanks,

Joe
 
Might be a sync issue.
If it is a media gateway. Set sync timing in media gateway.

Will
 
Thanks. I set it to pass through and still no luck. It was set at T38. standard.

How do I set the sync in the GW. I did telent into the GW and "set sync inter pri v2". Then I looked at the gui at network time sync, and it says "currently there are no peers present on the system". ANy ideas?

Thanks!
 
set sync interface primary v2

then

set sync source primary

then

copy run start



Will
 
Thanks for this advise. I did this and also did a "show sync timing", and it came back with "hardware failure". Yet the voice calls are fine??

I am going to swap the ds1 board and see what happens. Any other suggestions?? Anyone ever see this before?

Joe
 
Code:
Command: list configuration ds1

                       SYSTEM CONFIGURATION - DS1 Circuit Packs

Location   Code    Vintage     Signaling         Name              CSU MOD

002V1      MM710BP HW11 FW044  isdn-pri          PRI Quest         n/a
002V2      MM710BP HW11 FW044  isdn-pri          PRI to IPoffice   n/a

show mg list_config
show sync timing
clear sync interface primary
clear sync interface secondary
set sync interface primary
set sync interface secondary
set sync source primary
set sync source secondary
set sync source local
set sync switching disable
set sync switching enable
MG-002-2(super)# show mg list_config

SLOT  TYPE   CODE   SUFFIX  HW VINTAGE  FW VINTAGE   VOIP FW
----  ------ -----  ------  ----------  -----------  -------
v0    G700   DAF1   A       00          25.40.0(B)   70
v1    DS1    MM710  B       11          44           N/A
v2    DS1    MM710  B       11          44           N/A
v3     -- Not Installed --
v4    DCP    MM712  A       3           8            N/A
MG-002-2(super)# show sync timing

SOURCE     MM                   STATUS                   FAILURE
---------  -------------------  -----------------------  ---------------
Primary                         Not Configured
Secondary                       Not Configured
Local      v0                   Active                   None

Active Source: v0               Sync Source Switching: Disabled
MG-002-2(super)# configure
MG-002-2(configure)# set sync interface primary v1
MG-002-2(configure)# set sync source primary
MG-002-2(configure)# set sync switching enable
MG-002-2(configure)# show sync timing

SOURCE     MM                   STATUS                   FAILURE
---------  -------------------  -----------------------  ---------------
Primary    v1                   Active                   None
Secondary                       Not Configured
Local      v0                   Standby                  None

Active Source: v1               Sync Source Switching: Enabled


A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

36 years Bell, AT&T, Lucent, Avaya
Tier 3 for 26 years and counting
 


Hers is what it looks like now. I have it to "local" but I need primary. WHen it is in primary however, I get either a HW failure or Loss of SIgnal.


G350-002(super)# show mg list_config
SLOT TYPE CODE SUFFIX HW VINTAGE FW VINTAGE
---- -------- ---------- ------ ---------- -----------
v0 G350 A 1 30.13.2(A)
v1 S8300 ICC C 5 4
v2 E1T1 MM710 B 11 47
v3 DCP MM717 A 4 11
v4 Analog MM711 A 25 73
v5 Analog MM711 A 27 73
v6 -- Not Installed --
v7 Analog (on-board) A 3 67
G350-002(super)#
G350-002(super)# clear sync interface primary
Done!

G350-002(super)# clear sync interface secondary
Done!


G350-002(super)# set sync interface primary v2
Done!

G350-002(super)# set sync source primary
Done!

G350-002(super)# sh sync timin

SOURCE MM STATUS FAILURE
--------- ------------------- ----------------------- ---------------
Primary v2 Standby Loss of Signal
Secondary Not Configured
Local v0 Active None

Active Source: v0 Sync Source Switching: Enabled

Done!

G350-002(super)# show sync tim

SOURCE MM STATUS FAILURE
--------- ------------------- ----------------------- ---------------
Primary v2 Standby Loss of Signal
Secondary Not Configured
Local v0 Active None

Active Source: v0 Sync Source Switching: Enabled

Done!
G350-002(super)# set sync source local
Done!
G350-002(super)# sh sync tim

SOURCE MM STATUS FAILURE
--------- ------------------- ----------------------- ---------------
Primary v2 Locked Out Loss of Signal
Secondary Not Configured
Local v0 Active None

Active Source: v0 Sync Source Switching: Enabled

Done!
G350-002(super)# set sync switching disable
Done!
G350-002(super)# set sync switching enable
Done!
 
Your E1 is showing loss of signal so your Active sync source is your local Media Gateway. When you get your E1 up and working, it will switch back to the primary v2 Active

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

36 years Bell, AT&T, Lucent, Avaya
Tier 3 for 26 years and counting
 
Here is what I have now. How can I get it off local and onto primary? Thanks!

G350-002(super)# set sync switching enable
Done!
G350-002(super)# sh sync tim

SOURCE MM STATUS FAILURE
--------- ------------------- ----------------------- ---------------
Primary v2 Standby Loss of Signal
Secondary Not Configured
Local v0 Active None

Active Source: v0 Sync Source Switching: Enabled

Done!
G350-002(super)#
 
Avayatier3,

All the voice calls are working and sound fine. However, the "sh sync timing" inticates failure. So do you agree I have a bad ds1 card, or ???

Thanks,

Joe
 
display ds1 2v2

Your ds1 appears to think it's optioned for E1

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

36 years Bell, AT&T, Lucent, Avaya
Tier 3 for 26 years and counting
 
DS1 CIRCUIT PACK

Location: 002V2 Name: Seattle PRI
Bit Rate: 1.544 Line Coding: b8zs
Line Compensation: 1 Framing Mode: esf
Signaling Mode: isdn-pri
Connect: network
TN-C7 Long Timers? n Country Protocol: 1
Interworking Message: PROGress Protocol Version: b
Interface Companding: mulaw CRC? n
Idle Code: 11111111
DCP/Analog Bearer Capability: 3.1kHz

T303 Timer(sec): 4


Slip Detection? n Near-end CSU Type: other

Echo Cancellation? y Block Progress Indicator? n
EC Direction: inward
EC Configuration: 4
 
looks good, E1T1 appears to be normal on g350

You may have bad mm710B - Not sure why it shows loss of signal in the MG but you say it's working.

status signal 20
status trunk 20

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

36 years Bell, AT&T, Lucent, Avaya
Tier 3 for 26 years and counting
 
try reseating your mm710 and see if the loss of signal goes away.

This could also be an issue with the g350. Do you have another one to test this in?

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

36 years Bell, AT&T, Lucent, Avaya
Tier 3 for 26 years and counting
 
Sig Group...

STATUS SIGNALING GROUP

Group ID: 20 Active NCA-TSC Count: 0
Group Type: isdn-pri Active CA-TSC Count: 0
Signaling Type: facility associated signaling
Group State: in-service


Primary D-Channel


Port: 002V224 Level 3 State: in-service


Secondary D-Channel


Port: Level 3 State: no-link





Trunk 20....


TRUNK GROUP STATUS

Member Port Service State Mtce Connected Ports
Busy

0020/001 002V201 in-service/idle no
0020/002 002V202 in-service/idle no
0020/003 002V203 in-service/idle no
0020/004 002V204 in-service/idle no
0020/005 002V205 in-service/idle no
0020/006 002V206 in-service/idle no
0020/007 002V207 in-service/idle no
0020/008 002V208 in-service/idle no
0020/009 002V209 in-service/idle no
0020/010 002V210 in-service/idle no
0020/011 002V211 in-service/idle no
0020/012 002V212 in-service/idle no
0020/013 002V213 in-service/idle no
0020/014 002V214 in-service/idle no
 
Oh yeah...

I did reset it and it would either say HW Failure or loss of signal. I'm shping a replacement mm710 because I'm thinking this might be the issue. I dont have another system on site to test, but I did test the replacement card before shipping it to the remote office.

If it continues to fail, shall I suspect the G350 is bad???? The carrier was already on site with a T-bird, and ran clean, (which I suspected). I show no errors on a li meas ds1...
 
Avayatier3,

I swapped the ds1 card today and the voice channels did not come up. I went and got another card (both were mm710, not 710B), and the same. The voice channels did not come up. The second card was from a working system. I put the 710B back in and the voice channels came up, but again, without being able to sync to the primary.

I'm assuming that I have a bad chasis. Any suggestions before I order a new one?

Joe..
 
mm710 and mm710B are different packs
list config board 2v2 may show a conflict when programmed as mm710B but you have mm710 plugged in.

That being said, many packs may not operate correctly with these conflicts. display / change circuit-pack x (cabinet)
display / change media-gateway x (MG)

An example of this with legacy hardware would be replacing a ds1 tn767e with a tn464 or a tn464c with a tn464F.
display / change will show conflicts.

You may have to completely remove programming for trunk ports, signal-group, ds1, sync, etc. with old board,
plug in new board (different type) and reprogram all of this to match what was just unprogrammed. It may take all this to use a different board type as a substiute for the questionable board to function with this different hardware.


A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

36 years Bell, AT&T, Lucent, Avaya
Tier 3 for 26 years and counting
 
When ever I have had this problem with voice calls working but not fax calls it was a timing issue. Are you using one of your pris to time your system or is your system self timing.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top