Can't dial out with Authcode, Fast busy's all around.

[esoare]

What a pain. I know something isn't programmed right, but I checked everything that I know of.

Anyone want to take a dip into AuthCodes again?

dial 91503NxxNxxx# + 962 <-- Authcode (fast busy after the 96)
dial 77+962 + 91503NxxNxxx# : 77 <-- FFC Authcode (fast busy after last #)

Why won't the 1st way work? It gives a fast busy after the 2nd of 3 digits? Confused look.

Why doesn't the 2nd way work?

Info on things.


TYPE AUB
CUST 0

CUST 00
ALEN 03
ACDR YES
AUTHCOD_ALRM OFF
RANR X
ACLE YES
BRST 04
RTRY YES
RAN2 X
AUTO NO

CLAS COS TGAR NCOS CLAS COS TGAR NCOS CLAS COS TGAR NCOS

000 UNR 00 03 001 UNR 00 00 002 UNR 00 00
003 UNR 00 00 004 UNR 00 00 005 UNR 00 00
006 UNR 00 00 007 UNR 01 07 008 UNR 00 00



CODE 962 CLAS 007



SPN 1503 ( I created this as an SPN due to the fact that I want to test it for 011 )
FLEN 0
RLI 77
SDRR NONE
ITEI NONE


RLI 77
ENTR 0
LTER NO
ROUT 2
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
CNV NO
EXP NO
FRL 6
DMI 0
FCI 0
FSNI 0
SBOC NRR
OHQ NO
CBQ NO

ISET 0
NALT 5
MFRL 6


TYPE RDB
CUST 00
ROUT 2
DES 2WDID
TKTP DID
NPID_TBL_NUM 0
SAT NO
RCLS EXT
DTRK YES
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 6
SBN NO
PNI 00000
NCNA YES
NCRD YES
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 19
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DEXT NO
DNAM NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
TFD 0
DRNG NO
CDR NO


PAGE 002

MUS NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO



TYPE FTR_DATA
CUST 00
TBL
**DAPC**PREFIX TABLE NO: 00 **
UNKN**INTL**NATL**ESPN**LOCL**ELOC**ECDP**
UNKN*
E164* 00 0
PRIV*
E163* 00 0
TELX*
X121*
NATL*

OPT AHA BIND BIXA BLA CFF CFRD
COX CPA CTD DBA DNX DSX
HTU HVA XBL IC1 IDP XLF
IHA XTG FKA LOD LRA MCI
MWUD PVCD REA RNA
RTR RTA ROX SBD SYA
TTAD VOBD CWRD HLPD HRLD
CXOA
DGRP 500
IRNG NO
PKND 1
SPRE 31
PREO 0
BPSS NO
SRCD 0000
EEST YES
DTMF YES
EESD NO
MUS NO
ALDN
RECD NO
PORT 0
STCB NO
MCDC NO
NAUT YES
IDEF NO
MTAR NO
LEND NO
MSCD NO
CPCI NO
CONF_DSP
CNFFIELD NO
CNF_NAME CONF
INTFIELD NO
INT_NAME I
EXTFIELD NO
EXT_NAME E
BSFE NO
ASPCT 010

 

[RickyPone]

I thought you dial 16+authcode first. Then you get dt.

 

[esoare]

Correct. If SPRE was one. The SPRE on this system is 31.

I just had the user test with the way you suggested. But they still get a busy signal. I did a Trac DEV on the TN and it never hits Route 2 (a PRI). It should work. RLB 77 has FRL/MFRL to 6. And NCOS 7 is higher than FRL 6...NCOS issues?

SPRE + 6 + 962 Gets dial tone. Dials 91503NxxNxxx = Reorder


ACTIVE TN 008 0 06 14
ORIG 008 0 06 14 1 SCR MARP 0 4257 3904
TERM NONE
TDTN 0 SLOT 3 PTY SLOT 3
DIAL DN 91503NxxNxxx
MAIN_PM REOR
TALKSLOT NONE
QUEU DIAL
CALL ID 0 546

COS_ORIG UNR COS_TER UNR
TGAR_ORIG 1 TGAR_TER 0
NCOS_ORIG 7 NCOS_TER NONE
EXP_ROUTE NO

AUX


NON ACTIVE TN 024 0 06 03 MARP

 

[esoare]

It WAS the NCOS / NCTL in LD 87.

NCOS 7 was setup as FRL 0.

Changed NCOS 7 to FRL 7 and things started working!

Go figure. When it's programmed right, it works!

Thanks,