Can't configure my 891w to the Internet 3

[robbber]

I had a Linksys Wireless router and I bought this 891w to replace it, for home use. I have a DSL modem. So, i am coming off the modem into fe8 on the router. I just cant seem to get an IP from my ISP. I have no problem getting an IP if I connect the modem up directly to one of my PC's. DHCP is working fine from the router. Any help is appreciated. Here is my config:
rocket#sh run
Building configuration...

Current configuration : 6632 bytes
!
! Last configuration change at 21:33:09 PCTime Sun May 23 2010 by xxxxxxxx
! NVRAM config last updated at 21:31:14 PCTime Sun May 23 2010 by xxxxxxxxx
!
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
!
hostname rocket
!
boot-start-marker
boot-end-marker
!
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
logging console critical
enable secret 5 $1$lRUk$D5nwFFnEH0sTYkVIWj6Dm0
!
no aaa new-model
clock timezone PCTime -8
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
service-module wlan-ap 0 bootimage autonomous
!
crypto pki trustpoint TP-self-signed-3784225931
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3784225931
revocation-check none
rsakeypair TP-self-signed-3784225931
!
!
crypto pki certificate chain TP-self-signed-3784225931
certificate self-signed 01
3082024F 308201B8 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33373834 32323539 3331301E 170D3130 30353233 30313330
33385A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 37383432
32353933 3130819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100CB5E 59DC8CE6 F628FD3E DA8B4356 ECDCB2E0 14B87CD1 20D6BA2E 9EA8E42B
652CCDDD 5FEDD73B C722AFCE DA81F184 C9865484 9E596ED5 0581C60A BBBB6FE8
7B68707C 2D1E8F97 B9F5E950 EFBC9775 95D020BF 8C2B713F C995C107 5733822F
464ECC34 A514649D EDC07F75 CA465F32 72476B98 7FB3D07C 4D2F283C AEBE4710
3C030203 010001A3 77307530 0F060355 1D130101 FF040530 030101FF 30220603
551D1104 1B301982 17796F75 726E616D 652E796F 7572646F 6D61696E 2E636F6D
301F0603 551D2304 18301680 14EFF44E 0C27BFF2 07D13636 D757E9F7 AF8F599A
D2301D06 03551D0E 04160414 EFF44E0C 27BFF207 D13636D7 57E9F7AF 8F599AD2
300D0609 2A864886 F70D0101 04050003 81810014 D98FD6EC A6F9997E F1982FF9
CB664EB6 7A1DDF4B 3782123E 52FF03ED 4AF9D47C 0EED5156 A9AFDECB 7B6F0FBD
26EE6FFF 25687C10 E86D5D41 42186ECE 1D7EA365 3C7FB44D 37FD0002 AFB5C5EF
460B813F 1C5A6826 19DF1340 FA7D0F40 D10785CE 31EFF394 238E30C4 714CBEC3
04C1E0AC 1F704697 94BB6FD2 D4F47B43 B3DC84
quit
no ip source-route
!
!
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address 192.168.1.20
!
ip dhcp pool ccp-pool1
import all
network 192.168.1.0 255.255.255.0
default-router 192.168.1.20
!
!
ip cef
no ip bootp server
no ip domain lookup
no ipv6 cef
!
!
multilink bundle-name authenticated
!
!
username xxxxxxx privilege 15 secret 5 $1$eyQM$iFp3mJzel9CYQeX.gdz8M.
!
!
!
archive
log config
hidekeys
!
!
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh authentication-retries 2
!
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
!
interface FastEthernet5
!
interface FastEthernet6
!
interface FastEthernet7
!
interface FastEthernet8
description Outside World$ETH-WAN$
ip address dhcp
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
!
interface GigabitEthernet0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
shutdown
duplex auto
speed auto
!
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
arp timeout 0
!
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
!
interface Vlan1
description Internal LAN
ip address 192.168.1.20 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1412
!
interface Async1
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation slip
!
interface Dialer0
ip address dhcp client-id FastEthernet8
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1492
ip flow ingress
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname xxxxxxxxxx@sbcglobal.net
ppp chap password 7 153E5A1F05082A2631
ppp pap sent-username xxxxxxxx@sbcglobal.net password 7 153E5A1F05082A2631
!
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
!
ip nat inside source list 1 interface FastEthernet8 overload
!
logging trap debugging
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.255
dialer-list 1 protocol ip permit
no cdp run

!
!
!
!
!
!
!
control-plane
!
banner exec ^C
% Password expiration warning.
-----------------------------------------------------------------------

Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.

It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.

username <myuser> privilege 15 secret 0 <mypassword>

Replace <myuser> and <mypassword> with the username and password you want to
use.

-----------------------------------------------------------------------
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
!
line con 0
login local
transport output telnet
line 1
modem InOut
stopbits 1
speed 115200
flowcontrol hardware
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin udptn ssh
line aux 0
login local
transport output telnet
line vty 0 4
privilege level 15
login local
transport input telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
!
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end

 

[PeterHurst]

My first guess - Dialler hasn't got an IP NAT INSIDE command.

Also - I'm a littel worried about the way you're doing DHCP on the WAN side - it's not it's necessarily wrong it's just I'm not familiar with it. I'd suggest as the dialler makes the PPP it should do the DHCP and get an address rather than the Ethernet do it and pass an IP to the dialler.

You should be able to check if you're getting an Ip using sh int.

If it works like this I'd be interested what's going on - if you get an IP on the ethernet for example and that's part of the PPP connection - forgive me - I've not set up DSL only ATM

 

[unclerico]

is the modem in bridge mode??

I hate all Uppercase... I don't want my groups to seem angry at me all the time! =)
- ColdFlame (vbscript forum)

 

[ITBB]

Try to connect modem to the right interface (WAN)

 

[burtsbees]

interface Dialer0
ip address dhcp client-id FastEthernet8

try

interface Dialer0
ip address negotiated

That's the only part I looked at so far...more to follow...

/


tim@tim-laptop ~ $ sudo apt-get install windows
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Couldn't find package windows...Thank Goodness!

 

[robbber]

OK, thanks all. I will try suggested ideas tonight when I get home.
Unclerico, re: the modem being bridged...this is a sbc/yahoo(att) modem. I did see procedure below to configure modem but have not tried. There is no access code listed on the bottom of my modem. Now my model says 5100, not 5100b but I will check it out:

How can I put the 5100b in bridge mode? (#8722)
The modem itself, with the shipped firmware, supports 3 modes; PPPoE on board, Bridge mode, Bridge mode with IP Address pass Issuance. To put the modem in Bridge modem do the following:

1. In your web browser browse to »192.168.0.1 This address will be located on a yellow sticker on the bottom of your modem.

2. The first screen will ask you for your Modem Access Code. This also will be located on the same yellow sticker.

3. Select Advanced from the blue buttons on the left.

4. Click the PPP locations button.

5. The modem may ask your for the Modem Access Code again. If so type it in again and click continue.

6. Select the radio button labeled, "Bridged Mode (PPPoE is not used)"

7. Click Save Changes.

8. A "PPP Location Warning" page will come up. Click "Change PPP Location."

9. A "Restart Needed" page will come up. Click "Restart"

10. Reboot your computer and router (if applicable.) You will now need some form of PPPoE software on your computer or a router that supports PPPoE. Be warned that even if you are using Enternet 300 or XP/OSX's built in PPPoE SBC tech support will not troubleshoot connectivity issues until you have put your modem back in PPPoE on board mode.

 

[robbber]

making some progress, after your suggestion burt I am seeing an ip now on dialer0 from my ISP. I also added

ip nat inside

for dialer0 per suggestion from Peter. Still not getting out to the Internet. More suggestions welcome.....


rocket#sh run
Building configuration...

Current configuration : 6459 bytes
!
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
!
hostname rocket
!
boot-start-marker
boot-end-marker
!
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
logging console critical
enable secret 5 $1$lRUk$D5nwFFnEH0sTYkVIWj6Dm0
!
no aaa new-model
clock timezone PCTime -8
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
service-module wlan-ap 0 bootimage autonomous
!
crypto pki trustpoint TP-self-signed-3784225931
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3784225931
revocation-check none
rsakeypair TP-self-signed-3784225931
!
!
crypto pki certificate chain TP-self-signed-3784225931
certificate self-signed 01
3082023E 308201A7 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 33373834 32323539 3331301E 170D3130 30353235 30343032
32315A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D33 37383432
32353933 3130819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100CB5E 59DC8CE6 F628FD3E DA8B4356 ECDCB2E0 14B87CD1 20D6BA2E 9EA8E42B
652CCDDD 5FEDD73B C722AFCE DA81F184 C9865484 9E596ED5 0581C60A BBBB6FE8
7B68707C 2D1E8F97 B9F5E950 EFBC9775 95D020BF 8C2B713F C995C107 5733822F
464ECC34 A514649D EDC07F75 CA465F32 72476B98 7FB3D07C 4D2F283C AEBE4710
3C030203 010001A3 66306430 0F060355 1D130101 FF040530 030101FF 30110603
551D1104 0A300882 06726F63 6B657430 1F060355 1D230418 30168014 EFF44E0C
27BFF207 D13636D7 57E9F7AF 8F599AD2 301D0603 551D0E04 160414EF F44E0C27
BFF207D1 3636D757 E9F7AF8F 599AD230 0D06092A 864886F7 0D010104 05000381
81004757 172BCB7E A35FCCD0 8F7D38E1 39D8B19E 0B837CB7 AE3BBA43 AC603293
A7BD9475 D0441312 FDDD3C82 995BB0A9 30B88C47 57BDD14B 2EFCE9F6 520728F4
B9CE8D38 45069C23 6BCE4FC1 BDA1E04E A482AB0D 419F8F90 30FE8DE0 5EFBC570
D59A9890 5F57E8F7 5A6E6A2B 37ED0D23 05A1A122 8E10D85C BE075940 4564A67C E839
quit
no ip source-route
!
!
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address 192.168.1.20
!
ip dhcp pool ccp-pool1
import all
network 192.168.1.0 255.255.255.0
default-router 192.168.1.20
!
!
ip cef
no ip bootp server
no ip domain lookup
no ipv6 cef
!
!
multilink bundle-name authenticated
!
!
username xxxxxxx privilege 15 secret 5 $1$eyQM$iFp3mJzel9CYQeX.gdz8M.
!
!
!
archive
log config
hidekeys
!
!
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh authentication-retries 2
!
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
!
interface FastEthernet5
!
interface FastEthernet6
!
interface FastEthernet7
!
interface FastEthernet8
description Outside World$ETH-WAN$
ip address dhcp
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
!
interface GigabitEthernet0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
shutdown
duplex auto
speed auto
!
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
arp timeout 0
!
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
!
interface Vlan1
description Internal LAN
ip address 192.168.1.20 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1412
!
interface Async1
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation slip
!
interface Dialer0
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1492
ip flow ingress
ip nat inside
ip virtual-reassembly
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname xxxxxxxx@sbcglobal.net
ppp chap password 7 153E5A1F05082A2631
ppp pap sent-username xxxxxxxx@sbcglobal.net password 7 153E5A1F05082A2631
!
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
!
ip nat inside source list 1 interface FastEthernet8 overload
!
logging trap debugging
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.255
dialer-list 1 protocol ip permit
no cdp run

!
!
!
!
!
!
!
control-plane
!
banner exec ^C
% Password expiration warning.
-----------------------------------------------------------------------

Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.

It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.

username <myuser> privilege 15 secret 0 <mypassword>

Replace <myuser> and <mypassword> with the username and password you want to
use.

-----------------------------------------------------------------------
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
!
line con 0
login local
transport output telnet
line 1
modem InOut
stopbits 1
speed 115200
flowcontrol hardware
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin udptn ssh
line aux 0
login local
transport output telnet
line vty 0 4
privilege level 15
login local
transport input telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
!
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end

 

[unclerico]

ip route 0.0.0.0 0.0.0.0 di0

I hate all Uppercase... I don't want my groups to seem angry at me all the time! =)
- ColdFlame (vbscript forum)

 

[burtsbees]

Also, on dialer0, it is ip nat outside, not ip nat inside.

/

tim@tim-laptop ~ $ sudo apt-get install windows
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Couldn't find package windows...Thank Goodness!

 

[robbber]

unclerico, doh. Ok I will add

ip route 0.0.0.0 0.0.0.0 di0
thanks.
Burt thanks, will add that change too

 

[robbber]

I made changes to di0 below but still no joy.

ip route 0.0.0.0 0.0.0.0 di0
ip nat outside

here is the sh config + interfaces

rocket#sh ip int brief
Interface IP-Address OK? Method Status/Prot

Async1 unassigned YES NVRAM down/down

Dialer0 71.131.17.80 YES IPCP up/up

FastEthernet0 unassigned YES unset up/up

FastEthernet1 unassigned YES unset up/down

FastEthernet2 unassigned YES unset up/down

FastEthernet3 unassigned YES unset up/up

FastEthernet4 unassigned YES unset up/down

FastEthernet5 unassigned YES unset up/down

FastEthernet6 unassigned YES unset up/down

FastEthernet7 unassigned YES unset up/down

FastEthernet8 unassigned YES DHCP up/up

GigabitEthernet0 unassigned YES NVRAM down/down

NVI0 unassigned YES unset down/down

SSLVPN-VIF0 unassigned NO unset up

Virtual-Access1 unassigned YES unset up/up

Virtual-Access2 unassigned YES unset up/up

Vlan1 192.168.1.20 YES NVRAM up/up

Wlan-GigabitEthernet0 unassigned YES unset up/up

wlan-ap0 192.168.1.20 YES TFTP up/up

rocket#sh config
Using 5143 out of 262136 bytes
!
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
!
hostname rocket
!
boot-start-marker
boot-end-marker
!
security authentication failure rate 3 log
security passwords min-length 6
logging message-counter syslog
logging buffered 51200
logging console critical
enable secret 5 $1$lRUk$D5nwFFnEH0sTYkVIWj6Dm0
!
no aaa new-model
clock timezone PCTime -8
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
service-module wlan-ap 0 bootimage autonomous
!
crypto pki trustpoint TP-self-signed-3784225931
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3784225931
revocation-check none
rsakeypair TP-self-signed-3784225931
!
!
crypto pki certificate chain TP-self-signed-3784225931
certificate self-signed 01 nvram:IOS-Self-Sig#5.cer
no ip source-route
!
!
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address 192.168.1.20
!
ip dhcp pool ccp-pool1
import all
network 192.168.1.0 255.255.255.0
default-router 192.168.1.20
!
!
ip cef
no ip bootp server
no ip domain lookup
no ipv6 cef
!
!
multilink bundle-name authenticated
!
!
username rripplin privilege 15 secret 5 $1$eyQM$iFp3mJzel9CYQeX.gdz8M.
!
!
!
archive
log config
hidekeys
!
!
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh authentication-retries 2
!
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
!
interface FastEthernet5
!
interface FastEthernet6
!
interface FastEthernet7
!
interface FastEthernet8
description Outside World$ETH-WAN$
ip address dhcp
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
!
interface GigabitEthernet0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
shutdown
duplex auto
speed auto
!
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
arp timeout 0
!
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
!
interface Vlan1
description Internal LAN
ip address 192.168.1.20 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
!
interface Async1
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation slip
!
interface Dialer0
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname rripplinger@sbcglobal.net
ppp chap password 7 153E5A1F05082A2631
ppp pap sent-username rripplinger@sbcglobal.net password 7 153E5A1F05082A2631
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
!
ip nat inside source list 1 interface FastEthernet8 overload
!
logging trap debugging
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.255
dialer-list 1 protocol ip permit
no cdp run

!
!
!
!
!
!
!
control-plane
!
banner exec ^C
% Password expiration warning.
-----------------------------------------------------------------------

Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.

It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.

username <myuser> privilege 15 secret 0 <mypassword>

Replace <myuser> and <mypassword> with the username and password you want to
use.

-----------------------------------------------------------------------
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
!
line con 0
login local
transport output telnet
line 1
modem InOut
stopbits 1
speed 115200
flowcontrol hardware
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin udptn ssh
line aux 0
login local
transport output telnet
line vty 0 4
privilege level 15
login local
transport input telnet ssh
line vty 5 15
privilege level 15
login local
transport input telnet ssh
!
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end

 

[unclerico]

change this

ip nat inside source list 1 interface FastEthernet8 overload

to this

ip nat inside source list 1 interface dialer0 overload

I hate all Uppercase... I don't want my groups to seem angry at me all the time! =)
- ColdFlame (vbscript forum)

 

[burtsbees]

Also, access-list 1 needs to be

access-list 1 permit 192.168.1.0 0.0.0.255

if you want that subnet to get out, and not 10.10.10.0/24---192.168 is on the LAN...

/

tim@tim-laptop ~ $ sudo apt-get install windows
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Couldn't find package windows...Thank Goodness!

 

[unclerico]

uncle and burt, burt and uncle...that's just the way it was...we make a great team!!!

I hate all Uppercase... I don't want my groups to seem angry at me all the time! =)
- ColdFlame (vbscript forum)

 

[robbber]

thanks uncle and burt. glad youre havin a good time and sooooo patient with this

 

[unclerico]

no problem. what's the status??

I hate all Uppercase... I don't want my groups to seem angry at me all the time! =)
- ColdFlame (vbscript forum)

 

[robbber]

I wont be able to check till tonight, will post then or tomorrow am

 

[robbber]

oh man I screwed up. I had to change my password for ISP
so How do I change the ppp authenication password? I cant do it through the gui:

!
interface Dialer0
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname rripplinger@sbcglobal.net
ppp chap password 7 153E5A1F05082A2631
ppp pap sent-username rripplinger@sbcglobal.net password 7 153E5A1F05082A2631
!

 

[unclerico]

ppp chap password <password>
ppp pap sent-username rripplinger@sbcglobal.net password <password>

just for future reference, always scrub your config of usernames, passwords, and at least the last octet of your real IPs. we can very easily decrypt your password

I hate all Uppercase... I don't want my groups to seem angry at me all the time! =)
- ColdFlame (vbscript forum)

 

[burtsbees]

Yup. The level 7 passwords are nothing more than a Vigenere cypher, circa 1500 A.D. ...VERY weak!

/

tim@tim-laptop ~ $ sudo apt-get install windows
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Couldn't find package windows...Thank Goodness!