Can't change ATDN

[mx103]

In my 61C I have 3 cot's ATDN to 7713. which is an ACD on site. I need to change the ATDN to 4529 which is a DN at another location.

I can 4 digit dial the ext 4529 from my phone and the call completes fine.

The switch does not allow me to change the ATDN to a number which is not on site.

Is there something in programming I can change to make this happen.

I'm listing the COT and route below.

TN 4 1 2 7
DATE
PAGE
DES
TN 004 1 02 07
TYPE COT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
NCOS 7
RTMB 10 1
ATDN 7713
SIGL GRD
SUPN NO
CLS UNR DTN WTA LPR APN PIP THFD
P10 NTC
DATE 8 APR 2010



PRT
TYPE RDB
CUST 0
ROUT 10
TYPE RDB
CUST 00
ROUT 10
TKTP COT
PRIV NO
SAT NO
RCLS EXT
DTRK NO
PTYP ACO
AUTO YES
ICOG ICT
STEP
ACOD 810
TARG 15
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 512
GRD 896
TFD 0
LEXT 100
SST 3 0
NEDC ETH
FEDC ETH
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DRNG NO
CDR YES
INC NO
QREC YES
OAL YES
AIA YES
OAN YES
OPD NO
NATL YES
MUS YES
MRT 11
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
MANO NO
OHQ NO
OHQT 00
OHTD NO
REQ

thanks

 

[bignose21]

Print DNB 4295 in LD20 what is it? If it is a TSC/DSC then I don't think you can ATDN to them. You could leave it as it is if there is nobody in that ACD group and set the NCFW to go to 4295 (or use another ACDN, same deal).

 

[mx103]

DNB 4529 which is where I want it to go to is in another PBX at another location.

I tried NCFW and the call still rings to 7713.


PRT


TYPE ACD


CUST 0


ACDN 7713




TYPE ACD

CUST 0

ACDN 7713

MWC NO

DSAC NO

MAXP 5

SDNB NO

BSCW NO

ISAP NO

RGAI NO

ACAA NO

FRRT 17

FRT 4

SRRT

NRRT 18

FROA YES

NCFW 4529

FORC NO

SPCP YES

OBTN NO

CWTH 1

NCWL YES

CWLF 1

CWLW 1

BYTH 2

OVTH 5

TOFT NONE

HPQ NO

OCN NO

OVDN

IFDN

OVBU LNK LNK LNK LNK

EMRT

MURT 11

STIO 4

TSFT 20

HOML NO

RDNA NO

DAL NO

RPRT YES

RAGT 16

DURT 30

RSND 4

FCTH 20

CRQS 100



MEM AVAIL: (U/P): 3243360 USED: 375339 TOT: 3618699

 

[PERRYPJ]

When you forward your phone to 4529 does it go, if so build a Phantom DCFW to 4529 then place that DN of the Phantom in the ATDN

OLD ROLMEN WORKING ON NORTELS AND AVAYA

 

[Firebird Scrambler]

I see that you want to change the ATDN to 4529. I'm guessing that your ESN /CDP codes aren't broken down enough to allow you to use 4529. Check in LD 20 as suggested for a DNB of 4 or 45 etc.

I bet 4529 isn't listed as a separate CDP entry?. It's the same problem if you want to entry in a NITE DN. As suggested above, the workaround is to create a ACD or Phantom DN (ACD is best!) using any spare number and put that as the ATDN with a NFCW (ACD) or DCFW )Phantom) to 4529.

All the best

Firebird Scrambler
Meridian Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[johnpoole]

build an analog 4529 with a higher ncos cls cfxa ftr cfw x scpw xxxx, set cdb option to cff, then use rcfw to forward the analog off site.. works every time..

the block may be because the only ncos is the inbound trunk, by stepping through a 500, you can assign ncos and by changing to cff the forwarding station's ncos allows the cfxa

john poole
bellsouth business
columbia,sc