Cannot Connect to Callpilot thru Web page

[mbhamra1972]

i am new to callpilot. i am trying to connect to callpilot manager thru internet explore but i have no luck. it would be realy great if i can get some help. i have connected to serial port and data as follow.



CallPilot 150 Boot Loader V1.5.19
(C) 2001 Nortel Networks

--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.1.10
LAN interface's subnet mask is 0xffffff00
IP address of default gateway to other networks is 192.168.1.1
HARDWARE PARAMETERS:
Serial channels will use a baud rate of 9600
This board's ethernet address is 0:60:38:BE:34:24
CALLPILOT BOOTLOADER PARAMETERS:
Execution Mode: Load CallPilot
Source File System Parameters:
Device: ATA Disk
Source File List Name: filelst.lst
Destination File System Parameters:
Device: ATA Disk
File List Name: filelst.lst
Format Target Device: Y
Boot File Name: CallPilot.bin
After board is reset, start-up code will wait 2 seconds
--------------------------------------------------------------------------
To change any of this, press any key within 2 seconds


Automatic Update Mode Enabled!
To Change Update Mode to Manual, press any key within 10 seconds

Dialog Boot Sequence Enabled!
Using Dialog Parameters

Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SanDisk SDP 5/3 0.6
AtaInit: completed
Done.
Detecting ATA Cards...
Device found in Slot A:
Model: SanDisk SDCFB-64
Serial: 111903G0403E0806
Rev.: Vdi 1.24
Mounted 10.256
Loading 10.256/CallPilot.bin... Done.
Unmounting 10.256
Transferring control to the downloaded code

I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 4 channels
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SanDisk SDP 5/3 0.6
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI...

Standard output device initialized...
7.1\safe not found
Pseudo device initialized...
TFTP device initialized...

Login:

Type "test" to stop auto boot

Starting Access/2 and Voicemail
SysConfig file does not exist. Use default!!!
Opening DSP Msg logfile
DSP[0]: 1.50.51.A4 June 24, 2003
DSP Abstraction Layer Binding to port 5001
DSP Abstraction Layer Accepting...
Language Debug: Reading '7.1\access2\runtime\alarm0.dat'.
Read language file '7.1\access2\runtime\alarm0.dat'.
Loaded 1 of 1 language file(s). Default language: 0 (hex).
Curr File Pool Path='7.0\access2\FILEPOOL\0\*.*'
Curr File Pool Path='7.1\access2\FILEPOOL\0\*.*'
OSA DBG: pSOS_ERR: ResumeTask - t_resume rc =15
TCM 1: Channel 0: DOWN
TCM 2: Channel 2: DOWN
DCHCNTRL - DCH0 Reader created
DCHCNTRL - DCH1 Reader created
DCHCNTRL - DCH2 Reader created
DCHCNTRL - DCH3 Reader created
DCHCNTRL - Number of D-channels trying :2
DCHCNTRL - ALERT: All TCMs are Out of Sync. Reset hardware if a new KSU is conne
cted.
DCHCNTRL - ALERT: System will restart after 120 seconds
DCHCNTRL - ALERT: To stop rebooting, enter stopreboot
I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 4 channels
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SanDisk SDP 5/3 0.6
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI...

Standard output device initialized...
7.1\safe not found
Pseudo device initialized...
TFTP device initialized...


now from this i have couple questions.
1. do i have callpilot 100 or 150
2. do i need any other software to connect thru web.

thanks..

 

[phoneguy427]

If your network addressing is not within the 192.168.1.1 scope,then you need to set up a pc with an address something like 192.168.1.10 and connect a patch cable directly to the call pilot. Then go to 192.168.1.1 in explorer and you should be able to get in. Then you can change the call pilot addressing to match your network and you will be able to access it anywhere on your network. It looks like a 150, the easy way to tell, 2 lights on the left side cp100, 4 lights on the left cp150.

 

[exsmogger]

192.168.1.10 is the IP address of the CP. Change your PC's IP address to 192.168.1.11 and then try to connect to 192.168.1.10 using an ethernet crossover cable.

Brian Cox
Georgia Telephone

http://Georgia-Telephone.com

http://www.linkedin.com/in/briancox1952