cannot call out

[korexxkun]

Im working on an option 11c. I have a route that uses an acess code 9 as follows:

>ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 9

TYPE RDB
CUST 00
DMOD
ROUT 9
DES PH
TKTP COT
NPID_TBL_NUM 0
PRIV NO
RPA NO
SAT NO
RCLS EXT
DTRK NO
ISDN NO
PTYP ACO
AUTO YES
ACMP NO
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD 9
TARG
BILN NO
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GTO 896
GTI 896
ARP 3
SFB 3
CRD 512
TFD 0
LEXT 100
SST 3 0
DTD NO
SCDT NO
2 DT NO
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DDO NO
DRNG NO
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
MUS NO
MR NO


PAGE 002

PANS YES
MANO NO
EQAR NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
TTBL 0
ATAN NO
OHTD NO
OPR NO
RCAL NO
MCTS NO
ALRM NO
ART 0
PECL NO
DCTI 0
SGRP 0
AACR NO

when i dial 9 it give me a dialing tone, i dial the number and theres silence, after a while it goes back to a dialing tone without going out at all.
i traced the extension and i got this
>ld 80
TRA000
.trac 0 6105

ACTIVE TN 001 0 00 04
ORIG 001 0 00 04 MARP 0 6105 500
TERM 003 0 00 06 COT RMBR 9 1
TTR 000 0 00 04
DIAL 0 16 TTR 50
RCVR 54 SET 22

DIAL DN 972400
MAIN_PM DIAL AUX_PM OUTPULSE
TALKSLOT ORIG 18 TERM 50
EES_DATA:
NONE
QUEU 128
CALL ID 0 1242

any ideas anyone? Right nw i only get a dialing tone for 9 and after dialing the number it goes back again to the dialing tone.
the extn in question is programmed thus:
REQ PRT
TYPE: tnb
TN 1 4
DATE 6105

SCH0830

DATE
PAGE
DES

DES BENIN
TN 001 0 00 04
TYPE 500
CDEN 4D
CUST 0
WRLS NO
DN 6105 0 MARP
AST NO
IAPG 0
HUNT
TGAR 1
LDN NO
NCOS 7
SGRP 0
RNPG 0
XLST 0
SCI 0
SCPW
SFLT NO
CAC_MFC 0
CLS TLD DTN FBD XFA WTA THFD FNA HTD ONS
LPR XRD CWD SWD MWD RMMD SMWD LPD XHD SLKD CCSD LND TVD
CFTD SFD MRD C6D CNID CLBD AUTU
ICDD CDMD EHTD MCTD
GPUD DPUD CFXD ARHD OVDD AGTD CLTD LDTD ASCD
MBXD UDI RCC HBTD IRGD IAMD DDGA NAMA MIND
NRWD NRCD NROD CRD PRSD MCRD
EXR0 SHL ABDD CFHD
USRD BNRD OCBD RTDD RBDD RBHD FAXD FTTC
FDSD NOVD
RCO 0
AACS NO
MLWU_LANG 0
FTR FDN 7000
DATE 7 JUL 2011

 

[bignose21]

Not the best way of doing your out bound calls using and ACOD of 9, but from what you say you dial then after a couple of seconds it returns back to dial tone possibly your DTMF is setup incorrectly. Look in LD 97 under xctp and sysp. What country are you in?

 

[bignose21]

Also what is the stae of you DTR's (Stat in 32 program in 13) and TDS (Stat in 34 program in 17)

 

[RickyPone]

Change the phone to unr.

 

[korexxkun]

heres what i got from checking em out:

MEM AVAIL: (U/P): 5001199 USED U P: 372330 65958 TOT: 5439487
DISK RECS AVAIL: 468
REQ prt
TYPE parm
SCH0111

TYPE sysp

INTN = YES
QUIET CODE 0
THRESHOLDS 00004 00004
FLASH TIMERS 040 0800
TOHV 250
TDP 15
TID 150
TDPON 150
TPF 200
MFRL 0
MFTL0 00
MFTL1 00
XTRK MAKE/BREAK RATIO (PPS10) = 050
XTRK MAKE/BREAK RATIO (PPS12) = 050
XTRK MAKE/BREAK RATIO (PPS20) = 050
DEF (2006) 020
DEF (2008) 020
DEF (2216) 020
DEF (2616) 020
DEF (2000) 020
DEF (0500) 020
FNUM 2200



REQ
SCH0101
REQ prt
TYPE xctp

CPAD 0
TABL 00
DTMF 138
CFWT NO
P10P 030
S10P 031
2




>ld 34
TDS000
.stat tds
TDS202

Im currently in Nigeria

 

[korexxkun]

ive tried changing it to unr. the same problem persists

 

[bignose21]

LD 22
REQ prt
TYPE cequ

LD 20
REQ prt
TYPE DTR or XTD

Unluckly enough we don't have any switchs in Africa so I cant compair it to one of ours and not online (NTPs on my works PC)now till Monday to be able to check the DTMF 138. You have INTL set to yes so in LD 22 if you print PARM you should have PCML set to A (Alaw).

What release of switch is it, is it on SSC or MGC?

 

[bignose21]

The UNR thing would not have worked if you were getting Barred it wouldn't drop back to dial tone it would end call and give you re-order tone, which is not the case in your LD 80 Trace.