Can call 3353, but not cfw to 3353?

[EddieDuece]

Having a brain fart here. Lost a switch today so starting fresh. I can dial 3353 no problem but cannot call forward to it. That is out call pilot DN. Ideas?

 

[bignose21]

Stick a tnb of the set up and give us a clue

 

[jamie2]

Working with Eddie on this... Here is the TNB. We are trying to set key 19 as CFW 4 3353. 3353 is our Callpilot number. This is a 11C PBX trying to set the CFW key to call back to the 81C centralized voice mail. We can get to work when using CLS CFXA but that is not a solution for us, as it works as CFXD in all our other systems. We are set as CFO in both the RDR and FTR blocks. Maybe we'll try CFF again???

DES 211
TN 007 0 00 00
TYPE 3903
CDEN 8D
CUST 0
FDN 3353
TGAR 2
LDN NO
NCOS 2
SGRP 0
RNPG 0
SCI 0
SSU
LNRS 16
XLST
SCPW 1234
CLS CTD FBD WTA LPR MTD FNA HTA TDD HFA GRLD CRPD STSD
MWA LMPN RMMD SMWD AAD IMD XHD IRA NID OLA VCE DRG1
POD DSX VMD CMSD SLKD CCSD SWD LNA CNDA
CFTD SFA MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDD CDMD LLCN MCTD CLBD AUTU
GPUA DPUA DNDD CFXD ARHA FITD CLTD ASCD
CPFA CPTA ABDD CFHD FICD NAID BUZZ AGRD MOAD
AHA DDGA NAMA
DRDD EXR0
USMD USRA ULAD RTDD RBDD RBHD PGND OCBD FLXD FTTC DNDY DNO3 MCBN
CDMR
CPND_LANG ENG
RCO 0
HUNT 3353
LHK 1
LPK 2
PLEV 02
CSDN
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
MLNG ENG
DNDR 0
KEY 00 SCR 2501 0 MARP
CPND
NAME xxx
XPLN 27
DISPLAY_FMT FIRST,LAST
01 SCR 1825011 D MARP
CPND
NAME xxx
XPLN 27
DISPLAY_FMT FIRST,LAST
02 DIG 2 01 R
03 ADL 8
04
05
06
07
08
09
10
11
12
13
14
15
16 MWK 3353
17 TRN
18 AO6
19 CFW 4 (3353) = SCH5199
20 RGA
21 PRK
22 RNP
23
24 PRS
25 CHG
26 CPN
27 CLT
28 RLT
29
30
31
DATE 21 FEB 2014

 

[StanleySteamer]

Is the tie line route RCLS set for INT at the other sites?

 

[bignose21]

You cannot set that in software BTW you used to be able to but it would show against the key but still not be active (Like it shows the last one used on a set, but if you trac in LD 80 you would see the key idle). You have to do key "19 cfw 4" then activate at the set.

 

[jamie2]

Gives fast busy when trying to activate at the set.

Can set in software at other sites, but true that its not active until doing it on the set.

 

[jamie2]

turned out to be a simple resolution... MWI was missing in the RCAP!

 

[Funk49]

Of all the settings in RCAP, MWI (Message Waiting Indicator) not being flagged on your D Channel caused a fast busy when trying to call forward an extension to your voicemail DN? So how did adding Call Forward to External DN Allowed to the CLS allow the phone to be call forwarded to your voicemail DN?

 

[jamie2]

Funk... 'CXOA' was missing from the FTR_DATA OPT field, and was requiring us to have to use CFXA. With CXOA, the sets can be CFXD and still call forward to remote networked sites.