calling number CLID

[mjwald]

After switching to a new Telco, we have had some issues with our local dialing.

If we only send 7 digits, The Telco passes the call, but our sent caller ID is only 7 digits. This causes several issues.

If we send 10 digits, The Telco rejects the call, their tech say’s we need to send the call type as unknown. When I send it as unknown, my calling number gets turned into just my extension number, and the call is rejected.

(the numbers have been change to protect the innocent)

ANY ideas would be great!


CLID Table

ENTRY 0
HNTN 608
ESA_HLCL 5551212
ESA_INHN NO
ESA_APDN YES
HLCL 5551212
DIDN NO
DIDN_LEN 0
HLOC
LSC
CLASS_FMT DN






This is a d channel dump of the different formats I am trying to get to work to allow 10 digit dialing,
and 10 digit CLID for local calls.


********* FAILED *********
DCH 47 UIPE_OMSG CC_SETUP_REQ REF 00000290 CH 47 3 TOD 11:27:25 CK D1AB45A5
PROGRESS: ORIGINATING END IS NOT ISDN
CALLING #:5551212 NUM PLAN: E164 TON: LOCL
CALLED #:6084115555 NUM PLAN: E164 TON: LOCL


********* FAILED *********
DCH 47 UIPE_OMSG CC_SETUP_REQ REF 00000294 CH 47 17 TOD 11:28:09 CK D1AC9E77
PROGRESS: ORIGINATING END IS NOT ISDN
CALLING #:6085551212 NUM PLAN: E164 TON: NATL
CALLED #:6084115555 NUM PLAN: E164 TON: NATL


********* FAILED *********
DCH 47 UIPE_OMSG CC_SETUP_REQ REF 00000297 CH 47 18 TOD 11:28:39 CK D1AD895E
PROGRESS: ORIGINATING END IS NOT ISDN
CALLING #:6085551212 NUM PLAN: E164 TON: NATL
CALLED #:4115555 NUM PLAN: E164 TON: NATL


****** WORKS ********** (but only sending 7 digits)
DCH 47 UIPE_OMSG CC_SETUP_REQ REF 0000029B CH 47 18 TOD 11:29:01 CK D1AE3DFC
PROGRESS: ORIGINATING END IS NOT ISDN
CALLING #:5551212 NUM PLAN: E164 TON: LOCL
CALLED #:4115555 NUM PLAN: E164 TON: LOCL





The Telco then says that they want to see unknown, OK
The cs1000 then sends my CLID as my extension number.


********* FAILED *********
DCH 47 UIPE_OMSG CC_SETUP_REQ REF 000039C2 CH 47 9 TOD 13:13:23 CK FBA35274
PROGRESS: ORIGINATING END IS NOT ISDN
CALLING #:1234 NUM PLAN: E164 TON: UNKNOWN
CALLED #:6084115555 NUM PLAN: E164 TON: UNKNOWN

 

[KCFLHRC]

What is your ISDN Protocol and is the new Telco set up the same way. I'm guessing NI2 since that is the most common. Also do you know what kind of C.O. they have, is it a Nortel, AT&T or some other type? Maybe post your D-channel, route and trunk configs. You could try changing the call type to Natl. but that might not be the real fix.

 

[mjwald]

They would like me to set the called number to LOCL and the Calling number to NATL
I do not know how to set them differently.


Anyway here is the dch, It is NI2, I do not know what the telco's switch is.

ADAN DCH 47
CTYP MSDL
GRP 0
DNUM 8
PORT 3
DES Local47
USR PRI
DCHL 47
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO



RDB....
I have put two entries in bold. I can find neither of these in the input/output guide.
They would appear to be related to this issue.

TYPE RDB
CUST 00
ROUT 81
DES LOCAL47
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 4
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
MBXR NO
MBXOT NPA
MBXT 0
DSEL 3VCE
PTYP PRI
CNDP UKWN
AUTO NO
DNIS YES
NDGT 4
DDLY NO
DCDR YES
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 2000081
TCPP NO
PII NO
AUXP NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0 *
NDNO 0
DNAM NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952


PAGE 002

NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
DRNG NO
CDR YES
INC YES
LAST NO
TTA NO
QREC NO
OAL YES
AIA YES
OAN YES
OPD NO
CDRX YES
NATL YES
MUS YES
MRT 29
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
AACR NO


Trunk ...

DES LOCAL47
TN 047 01
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 4
RTMB 81 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID 47
AACR NO
DATE NO DATE

 

[mjwald]

So, I asked what there switch was.

EWSD Electronic Worldwide Switch Digital

Never heard of it. Now I'm worried.

 

[KCFLHRC]

Never heard of that one either. I was hoping it was a Nortel CO, there is a setting in the DMS under the LTDEF table called SL1 profile ,that sometimes needs to be enabled. I have always changed the Call Type through a DMI table to get these to work properly. I'm not sure what those entries on the route are for.

Sorry

 

[phones1]

eswd= Siemens = Pain in the arse

Remember if it doesn't work hit it harder

Scott UK