C.P. error code 4

[Wallysworld]

Hello all;

I have a c.p. that is giving me an error code. It starts out o.k., all lights flashing like normal, and then after a few minutes all the lights go dark and that's it. I connected through hyperterminal and this is what I see:


CallPilot 150 Boot Loader V1.5.19
(C) 2001 Nortel Networks

--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.110.10
HARDWARE PARAMETERS:
Serial channels will use a baud rate
This board's ethernet address is 0:14:C7:FF:C5:8B
CALLPILOT BOOTLOADER PARAMETERS:
Execution Mode: Load CallPilot
Source File System Parameters:
Device: ATA Disk
Source File List Name: filelst.lst
Destination File System Parameters:
Device: ATA Disk
File List Name: filelst.lst
Format Target Device: Y
Boot File Name: CallPilot.bin
After board is reset, start-up code will wait 2 seconds
--------------------------------------------------------------------------
To change any of this, press any key within 2 seconds


Automatic Update Mode Enabled!
To Change Update Mode to Manual, press any key within 10 seconds
Updating in Automatic Mode!

Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2.00
AtaInit: completed
Done.
Detecting ATA Cards...
Device found in Slot A:
Model: SILICONSYSTEMS INC 64MB
Serial: 316CT
Rev.: 2.29l
Mounted 10.256
Loading 10.256/CallPilot.bin... Done.
Unmounting 10.256
Transferring control to the downloaded code

I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 4 channels
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI...

Standard output device initialized...
7.1\safe not found
Pseudo device initialized...


Type "test" to stop auto boot

TFTP device initialized...

Login: Starting Access/2 and Voicemail
SysConfig file does not exist. Use default!!!
Open File Error e
Opening DSP Msg logfile
CadClassPubInit: Error Code = 4Access failed
System will reboot in 1 seconds
Synchronizing volume 7.0 ... Done!
I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 4 channels
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2.00
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI...

Standard output device initialized...
7.1\safe not found
Pseudo device initialized...


Type "test" to stop auto boot

TFTP device initialized...

Login: Starting Access/2 and Voicemail
SysConfig file does not exist. Use default!!!
Open File Error e
Opening DSP Msg logfile
CadClassPubInit: Error Code = 4


____________________________________________________________


Does anyone have any suggestions how I can get rid of this error code.
I am trying to use this with a mics at my workbench.

Thanks.

 

[fireeater]

when i have had the similar problem i changed the power supply

sometimes you don't get enough power from the unit to fully run the system

only happens with the older supplies it seems they go to half amperage but keep the same voltage

to err is human
to really f things up requires a computer

mike

http://www.ics-on.ca

 

[Deweyhumbolt]

Make sure it's disconnected from network to test.

Adversity is Opportunity