BUILD PRI TRUNK BETWEEN 2 PaBx

[thb68]

Hi,
I would like to setup a lonk using DS1 boards between G3Rv9 and à R016x.00.1.510.1 on the g3r QSIG feature is not available.
then I would like to build a private line.
trunk looks like this:
Group Number: 21 Group Type: isdn CDR Reports: y
Group Name: TIE_TULLE_G3T COR: 1 TN: 1 TAC: 7021
Direction: two-way Outgoing Display? n Carrier Medium: PRI/BRI
Dial Access? y Busy Threshold: 255 Night Service:
Queue Length: 0
Service Type: tie Auth Code? n TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4

My question is how I can configure DS1 for have one master and one slave without QSIG?

 

[thb68]

settings for DS1 on G3R :
DS1 CIRCUIT PACK

Location: 01D20 Name: tie
Bit Rate: 2.048 Line Coding: hdb3

Signaling Mode: isdn-pri
Connect: host
CentreVu Long Timers? n Country Protocol: etsi
Interworking Message: PROGress Protocol Version: b
Interface Companding: alaw CRC? n
Idle Code: 01010100
DCP/Analog Bearer Capability: 3.1kHz




Slip Detection? y Near-end CSU Type: other

setting for sig
SIGNALING GROUP

Group Number: 10
Associated Signaling? y Max number of NCA TSC: 0
Primary D-Channel: 01D2016 Max number of CA TSC: 0
Trunk Group for NCA TSC:
Trunk Group for Channel Selection:
Supplementary Service Protocol: a Network Call Transfer? n

trunk settings:
TRUNK GROUP

Group Number: 10 Group Type: isdn CDR Reports: y
Group Name: LIEN CAV COR: 1 TN: 1 TAC: 290
Direction: two-way Outgoing Display? n
Dial Access? y Busy Threshold: 255 Night Service:
Queue Length: 0
Service Type: tie Auth Code? n TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): enbloc/enbloc

Trunk Hunt: descend
Digital Loss Group: 13
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0

TRUNK FEATURES
ACA Assignment? n Measured: none Wideband Support? n
Internal Alert? n Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: n Send Calling Number: n
Used for DCS? n
Suppress # Outpulsing? n
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider

Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: n


Send UCID? n
Send Codeset 6/7 LAI IE? n Ds1 Echo Cancellation? n

US NI Delayed Calling Name Update? n

Network (Japan) Needs Connect Before Disconnect? n

on the other switch:
ds1 settings:
DS1 CIRCUIT PACK

Location: 130V4 Name: TIE
Bit Rate: 2.048 Line Coding: hdb3

Signaling Mode: isdn-pri
Connect: network
TN-C7 Long Timers? n Country Protocol: 12
Interworking Message: ALERTing Protocol Version: b
Interface Companding: alaw CRC? n
Idle Code: 01010100
DCP/Analog Bearer Capability: 3.1kHz

T303 Timer(sec): 4


Slip Detection? y Near-end CSU Type: other

Echo Cancellation? n

settings for sig:
SIGNALING GROUP

Group Number: 122 Group Type: isdn-pri
Associated Signaling? y Max number of NCA TSC: 0
Primary D-Channel: 130V416 Max number of CA TSC: 0
Trunk Group for NCA TSC:
Trunk Group for Channel Selection: X-Mobility/Wireless Type: NONE
TSC Supplementary Service Protocol: a Network Call Transfer? n

trun settings:
TRUNK GROUP

Group Number: 21 Group Type: isdn CDR Reports: y
Group Name: TIE_TULLE_G3T COR: 1 TN: 1 TAC: 7021
Direction: two-way Outgoing Display? n Carrier Medium: PRI/BRI
Dial Access? y Busy Threshold: 255 Night Service:
Queue Length: 0
Service Type: tie Auth Code? n TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4
Group Type: isdn

TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: automatic
Supplementary Service Protocol: c Digit Handling (in/out): enbloc/enbloc

Trunk Hunt: cyclical
Digital Loss Group: 13
Incoming Calling Number - Delete: Insert: Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0
Administer Timers? n CONNECT Reliable When Call Leaves ISDN? n
XOIP Treatment: auto Delay Call Setup When Accessed Via IGAR? n
TRUNK FEATURES
ACA Assignment? n Measured: external Wideband Support? n
Internal Alert? n Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: n Send Calling Number: y
Used for DCS? n Send EMU Visitor CPN? n
Suppress # Outpulsing? n Format: public
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider
Charge Conversion: 1
Decimal Point: none Replace Restricted Numbers? y
Currency Symbol: Replace Unavailable Numbers? y
Charge Type: units Send Connected Number: n
Network Call Redirection: none Hold/Unhold Notifications? n
Send UUI IE? y Modify Tandem Calling Number: no
Send UCID? n
Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation? n

Apply Local Ringback? n
Show ANSWERED BY on Display? y
Network (Japan) Needs Connect Before Disconnect? n

when I check status on g3R trunk is OOS
when I check status on switch i have

0021/001 130V401 OOS/FE-idle no
0021/002 130V402 OOS/FE-idle no
0021/003 130V403 OOS/FE-idle no
0021/004 130V404 OOS/FE-idle no
0021/005 130V405 OOS/FE-idle no
0021/006 130V406 OOS/FE-idle no


it's looks like that I have pb with signaling...
all help are welcom

 

[Tolson]

You did to the simple item of flipping the pairs if your using T1 Cabling or flipping the coax if your using that method right ?

 

[thb68]

Ok thanks tests on going I have found a pn on CM6 when you change ds1 settings chare are saved but not applied.
you need to remove the ds1 and setup at the first attemps correct settings for apply these settings..
no so easy during tests thanks Avaya