BUG253 and PRI222 Troubleshooting advise needed

[rachelle]

Just started... may stop on its own....

PRI222 DCH: 16 DATA: 0000005F

BUG253
BUG253 : 1420 15 00000000
BUG253 + 00AECFC0 004DD69E 00807107 00804B8C 00803D95
BUG253 + 008035D9 007FA1A8 007F9FF7 007F4FED 007F0882
BUG253 + 0103D3E1 0105B6D9 0105B591 0105B4D6 0105835A
BUG253 + 01057C04 0105719A 0103EC15 0103E945 0103E13D
BUG253 + 0103CC32 0100842E 01007232 01004910 010030D3
BUG253 + 01002936 007F1F5A 007FC319 007FC265 007FA008
BUG253 + 007F094E 00E29EC7 00E26C78 00E2697E 0196A90C
BUG253 + 01963BB1 01B46641


1420 isn't built in our PBX as anything. I don't know what 15 corresponds to. The PRI222 issue is also unfamiliar. DCH 16 goes to my loop 104 (goes to the cisco CallManager that sits behind my Nortel CS1000M MG, rls. 4.5 PBX). I did just make some adjustments to the RDB for this. See below and tell me what you think. I need to turn something off but, what??? Thoughts? UPDATE: I put the RDB for 104 back the way it was and the errors persist. I don't think that it is my route. It looks like something else is happening. Help.

TYPE RDB changed from
CUST 00
ROUT 104
DES VOIP
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC D100
SBN NO
PNI 00000
NCNA YES
NCRD YES no
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
DSEL VOD vce
PTYP PRI
AUTO NO
DNIS NO
DCDR YES no
ICOG IAO
SRCH LIN rrb
TRMB YES
STEP
ACOD 120490
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 5 0
NDNO 5 * 0
DEXT NO
DNAM NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3


PAGE 002

NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR YES no
INC YES did not exist
LAST YES did not exist
QREC NO did not exist
OAL YES did not exist
AIA NO did not exist
OAN YES did not exist
OPD YES did not exist
CDRX NO did not exist

SCH2017 see details below

NATL NO
TDG 0 1
VRAT NO
MUS YES no
MRT 0 did not exist
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR YES
ASID 17
SFNB
USFB
CALB 7 8

no matter where you go, there you are.
"This participation is persona and does not represent the United States Census Bureau." They make me say this.

 

[rachelle]

I turned off DCH 16 and disabled the three Loops that were running off of it. All messages stopped. The Cisco side of the house says that they have several individual ports going in and out of service. I am waiting on them to advise. Does anyone have a TIE to CallManager T1? I don't have a QSIG package so, TIE is what I needed to use, per the cisco team.

If anything jumps off the page, please give me a nudge in the right direction.

This is how they said to build the route:

TYPE RDB
CUST 00
ROUT 104
DES VOIP
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC D100
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
DSEL VCE I want this to be VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB I want this to be LIN
TRMB YES
STEP
ACOD 120490
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DEXT NO
DNAM NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3


PAGE 002

NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR YES
ASID 17
SFNB
USFB
CALB 7 8

no matter where you go, there you are.
"This participation is persona and does not represent the United States Census Bureau." They make me say this.