Big Mistake

[JustinTMI]

Well i think i screwed this one up..

Have an IP500, and i planned on putting it on a network.

In LAN1 I set the ip up 192.168.1.98 and my voicemail 192.168.1.99 voicemail shows up on the network fine, the IP office is nowhere to be found.

When i plug my laptop in change my network settings to 192.168.1.50 for my network address and try and connect to the IP office it will not connect no matter what i try it wont even see the IPOffice Unit.

I turned DHCP in the Lan1 tab to client as well.

Maybe I typed in IP Address wrong or im missing something?

when i take the cable plugged into ip office and plug it in to laptop i get the proper IP it is suppose to be so i know the cable is good.

Any idea how i can check the IPoffice to find out what the IP is set to with out DTE?

-Justin

 

[IPGuru]

if you did not change the lan 2 settings then it should still be actinga as a dhcp server on 192.168.43.1.

connect your laptop to the lan2 port & reconnect using this.
(usualy I woudl leave Lan2 like this if possible & set DHCP on lan1 to disabled.)

 

[hairlessupportmonkey]

try a network scan like Angry IP scanner

it wont show a host name but it will give you a fighting chance of finding it.

or

Download and install Solarwinds (trial) engineer tool, there is a MAC address network scanner in there, and its great for finding stuff on a network. it will even show you the device name (Network Alchemy - even a 406 shows up as this - not too sure what the ip500 shows up as)

 

[Bas1234]

Happend to me today, customer could not connect to the Lan2 port. They had put a WIFI in that network with the same IP address.....

Me happy....customer not.

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged
___________________________________________

 

[AVAYAPro]

Are you supposed to be able to pull configs and merge on LAN2/WAN?

I have tried to connect to an IP Office with Manager on an IP500v2 on LAN2/WAN before with no success.



ACS - IP Office Implement
ACA - IP Telephony Implement
CCNA - Cisco Certified Network Associate
MCP - Microsoft Certified Professional

I like stars

 

[mforrence]

Are you supposed to be able to pull configs and merge on LAN2/WAN?

I have tried to connect to an IP Office with Manager on an IP500v2 on LAN2/WAN before with no success."

This is an everyday thing for us... IPO doesn't care which port is used.

Mike

 

[Bas1234]

AVAYApro......turn off the Firewall on that LAN2...this is off by default and the only port with a FW. Or make sure port 69/50796/50802 is opened.

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged
___________________________________________

 

[Westi]

if you have the MAC address tehn open a command prompt
type ntbstat -R
then type in ntbstat -a ipbs-11-22-77 (where 11-22-77 are the last 6 digits of the MAC address tehn it should show you something like this

IPBS-11-22-77 <00> UNIQUE Registered
192-168-100-124<00> UNIQUE Registered
MAC Address = 00-01-3E-11-22-77

This is for the IP DECT stuff but should work for any MAC address.

Joe W.

FHandw., ACSS

insanity is just a state of mind

 

[chaunymony]

You can also plug your laptop into that lan 1 port and use wireshark to get the ip it's throwing out. I just did this on a 406v2 that was sitting in inventory that no one knew the ip of and save me from going DTE on that sucker. And to ditto what mforrence said, I too have used lan2 as a work around. It's a lovely port

 

[TomMills]

chaunymony, i do the same. As for not seeing the unit when plugged straight into it, forgetting to turn off your wireless adapter can cause this (-:

http://www.twitter.com/tem1985

ACSS-SME
fo shizzle ma nizzle.

 

[tlpeter]

Or if nothing works use DTE and type this:

at<enter>
at-debug<enter>
system<enter>

then you see all ip addresses


Homo sapiens non urinat in ventum

honey, i fried the IP Office !!!

Sarcasm, it's only one of the services I offer.