Trying to get an IP set to work over a VPN. VPN connection is established. Can ping devices from the remote side on the host side and vice versa. Issue seems to be with the BCM. I can ping the BCM from the LAN but I can not ping the BCM accross the VPN. The BCM will not ping outside the subnet.
Had IP set working over the LAN. Now set will not connect over the VPN.
Read lots of different posts with similar issues of the BCM not responding. Told that it is an issue with the BCM since the VPN router firewalls are disabled.
This info is from a cmd prompt on the BCM the BCM is 1.2, and 1.1 is the VPN router.
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 255.255.255.0 192.168.1.1 192.168.1.2 20
10.10.11.0 255.255.255.0 10.10.11.1 10.10.11.1 1
10.10.11.1 255.255.255.255 127.0.0.1 127.0.0.1 1
10.255.255.255 255.255.255.255 10.10.11.1 10.10.11.1 1
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
192.168.1.0 255.255.255.0 192.168.1.2 192.168.1.2 1
192.168.1.2 255.255.255.255 127.0.0.1 127.0.0.1 1
192.168.1.255 255.255.255.255 192.168.1.2 192.168.1.2 1
192.168.20.0 255.255.255.0 192.168.1.0 192.168.1.2 1
224.0.0.0 224.0.0.0 10.10.11.1 10.10.11.1 1
224.0.0.0 224.0.0.0 192.168.1.2 192.168.1.2 1
255.255.255.255 255.255.255.255 10.10.11.1 10.10.11.1
I am trying to determine what is stopping the BCM from reaching a public address. Is there a firewall built into the BCM that is stopping the traffic? Need help on how to change the BCM programming. BCM 200 Release 3.0 System licenced for 1 IP client and 16 mailboxes.
Had IP set working over the LAN. Now set will not connect over the VPN.
Read lots of different posts with similar issues of the BCM not responding. Told that it is an issue with the BCM since the VPN router firewalls are disabled.
This info is from a cmd prompt on the BCM the BCM is 1.2, and 1.1 is the VPN router.
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 255.255.255.0 192.168.1.1 192.168.1.2 20
10.10.11.0 255.255.255.0 10.10.11.1 10.10.11.1 1
10.10.11.1 255.255.255.255 127.0.0.1 127.0.0.1 1
10.255.255.255 255.255.255.255 10.10.11.1 10.10.11.1 1
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
192.168.1.0 255.255.255.0 192.168.1.2 192.168.1.2 1
192.168.1.2 255.255.255.255 127.0.0.1 127.0.0.1 1
192.168.1.255 255.255.255.255 192.168.1.2 192.168.1.2 1
192.168.20.0 255.255.255.0 192.168.1.0 192.168.1.2 1
224.0.0.0 224.0.0.0 10.10.11.1 10.10.11.1 1
224.0.0.0 224.0.0.0 192.168.1.2 192.168.1.2 1
255.255.255.255 255.255.255.255 10.10.11.1 10.10.11.1
I am trying to determine what is stopping the BCM from reaching a public address. Is there a firewall built into the BCM that is stopping the traffic? Need help on how to change the BCM programming. BCM 200 Release 3.0 System licenced for 1 IP client and 16 mailboxes.