BCM Centralized Vmail MCDN

[vztech]

I have a BCM 400 Rls 4.0 (site A) networked with SIP trunks to a BCM 50 Rls 3 (site B )

all patchs and MCDN keycode loaded

issue
all DID calls go through site A (PRI) Target line rcv 7xxx redirect to 87xxx ( 8 is dest code)to site B over SIP.

rings 4 times fwd no answer to vmail back to site A leave message all is good. I cannot get the message waiting lamp to light on the far end.
I believe I understand why. 8 is a dest code and vmail doesnt have the capability to realize it needs an 8 to get across the voip.
I was told I could out the target line 7XXX and create a destination code of 7XXX to use the voip route on DID calls.

tried that but I get intercept from telco on site A

MY question has anyone used destination codes only to route calls to another location? is this possible?

I tried changing it from private to public,prime set etc.

any thought for me to try would be great

Thanks






It's only dialtone-VZ

 

[gberger]

Destination codes is the only way to route calls to another location.
what is the extension's range at site b? are 87xxx or 7xxx(do you strip the 8?)?
If your extensions in site b are in the 7xxx, you're right, the call pilot is trying to notify mailbox 7xxx and has no clue about the "8".
That's why its really important do have a good dialing plan.
If site B is the only one that has dn's in the range 7XXX, i would suggest asking the telco to send you 7 or 10 digits on your PRI because you can't have a "receive digit" of 7xxx and have a destination code of "7" to route your calls to site B.
You'll have to reprogram your target lines to receive 7 or 10 digits and create a destination code of 7xxx with absorb "0", this way it will send then entire dn(7XXX) across the VoIP trunks.
Don't forget to enable "message notification" on each target line in site B.
Good luck!

 

[vztech]

I have 7xxx ext. I tried creating dest code for 7xxx on site A to site B but the DID call does not show on the BCM monitor and never hits site A. I get a reorder.

But if I create a target line to rcv 7XXX at site A it will come in.

It's only dialtone-VZ

 

[SupportDude]

How many digits is telco sending for your received number?

Do you have a "Prime Set" configured for the trunk your DID call comes in on?

-SD-

http://www.mysupportguy.net

 

[gberger]

At site A you cannot create a destination code of "7xxx" and at the same time program a target line with a receive digit starting with "7".
That's why in my previous post i told you to ask the telco to send you 7 or 10 digits.

 

[vztech]

(telco is sending 4 and I understand if they send me more digits I could get this to work with target line and a redirect) I have 150 target lines that I would like to keep from reprogramming if possible.

But I was told this should work with destination codes only.
Maybe the engineer is wrong.
My question
I have DID's coming into PRI at site A.
If I create a destination code of the extension at site B and pointed it to my SIP trunks route. which has the routing table already built. Should it work ?
I am not creating a target line at site A only a dest code.


If this is possible it's not working.I get a reorder from telco but if I make it a target line it hits the BCM 400 correctly. Maybe it has something to do with the protocols CSE vs SL1 vs none under IP trunking.


It's only dialtone-VZ

 

[vztech]

have DID's coming into PRI at site A.
If I create a destination code (at site A ) of the extension at site B and point it to my SIP trunks route. which has the routing table already built. Should it work ?
I am not creating a target line at site A only a dest code.


It's only dialtone-VZ

 

[cook1082]

It should work. Dest. code and route to B public.you should need a dest code of 7 route to VOIP trunks and recieve public the 4 digits. Also the gateway, a dest code of 7.

 

[vztech]

Thanks everyone

Problem solved
Argggg!!! I have 2 PRI's gave only 1 off the PRI's the remote access package and not the other.call were coming in on the PRI that didn't have access.


Thanks again



It's only dialtone-VZ