BC12 integrated DECT problems

[slash50]

Hi,

I have our in house test system, open license, and want to start DECT function.

I have installed 1 x ELU31 and wired out to the frame. I have installed TSR 901 1234 cable between the sync Rx and Tx on the same board. I have set SARI to 12345678. I have initiated CXCFI and CXRFI.

I have cabled RJ45 cable from base station BS330 (RJ45 blue pair and green pair) to the ELU31 cable (Krone block Blue pair and Orange pair)

However the base station does not start, it cycles through the 3 colour LCD and the following are the printouts I receive from Md110.

<CXRFP:FPI=1,RPN=ALL;
                   
CORDLESS EXTENSION RADIO FIXED PART DATA                 
                   
                   
FPI =      1    BPOS = 001-1-60                          
                   
RPN   OPERATING STATE   BLOCKING STATE
1     NOT RESPONDING    UNKNOWN                          
END
 
<CXCFP:fpi=all;
CORDLESS EXTENSION COMMON FIXED PART DATA                
SARI = 12345678    
                   
                   
FPI     BPOS      PARI       RFP   TRM   DELAY  >
     1  001-1-60  12345E2E   1     0         0  >

< SYNCH ROLE       SYNCH INFO  MODE  ACDM   COMP
< NOT READY        01010       NORM  NO       0 

END
 
<

Can anyone please help? It's the first I have instaled DECT )

 

[whosrdaddy]

does you test system has external lines?

if not, your LSU clock is not good enough for the ELU31.

2 solutions, swap you LSU for a "trained" one.
or put external line on your system. note that the LSU clock training is a slow process and can take several days.

if you have external lines (and you sync on them),
the sync cable on the ELU31 is probably incorrect.

Cheers,
Daddy

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[slash50]

Cheers Daddy,

The system has an E1 circuit connected to BT and takes sync from that. Do you know which way to use sync cable for a 1 card system?

 

[whosrdaddy]

you have to make one yourself (like I did) will post layout later...

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[whosrdaddy]

Ok, here's the layout:

C30-C32
C24-C22
A32-A24
A30-A22
A28-A20
A26-A18

Cheers,
daddy

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[rfpui]

Have You ELU 31/1 or ELU 31/2?

From Alex:
A system with only one ELU31/1 board still requires a RING cable (TSR 901 1233/2300) running from the TX port to the RX port on the same board.

A system with only one ELU31/2 board still requires a RING cable (TSR 901 1234/2300) running from the TX port to the RX port on the same board



----------------------------------
If anything can go wrong, it will.
(Murphy's Law)

 

[whosrdaddy]

also take another SARI number, I have had bad expierences with 12345678, take something in the range ABxxxxxx.

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[whosrdaddy]

slash, what firmware is the board running (and is it a /2 or not??) my cable scheme is for /1.

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[slash50]

I am using a ELU31/1 but with a 901 1234 cable.....

I don't have the tools or pieces to make my own cable, so I may have to order the 901 1233 cable from supplier.

Thanks for all your help so far, very kind )

I will also change the SARI number