Hi to All
I am running Arcserve 11.5 SP3 on a redhat linux 4 update 7 server. The server is a DL380 G4.
The tape drive being used is a Adic Suploader 3 (Ultrium 4) Drive. Tape is a Imation 800/1.6 TB.
All appear to be OK, We have one interface thats assigned to be used by oracle and thats appears to work fine. The other instrface was to be used by Arcserv for backups.
When I backup I see about 670 MBPS Which was looking to see about 1,400 MBPS. Is there away in CA config to have backup only use the interface for eth1 and not eth0
Any help with this would be thankful
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: g
Link detected: yes
Settings for eth1:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: g
Link detected: yes
Thanks in Advance
Rob.
I am running Arcserve 11.5 SP3 on a redhat linux 4 update 7 server. The server is a DL380 G4.
The tape drive being used is a Adic Suploader 3 (Ultrium 4) Drive. Tape is a Imation 800/1.6 TB.
All appear to be OK, We have one interface thats assigned to be used by oracle and thats appears to work fine. The other instrface was to be used by Arcserv for backups.
When I backup I see about 670 MBPS Which was looking to see about 1,400 MBPS. Is there away in CA config to have backup only use the interface for eth1 and not eth0
Any help with this would be thankful
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: g
Link detected: yes
Settings for eth1:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: g
Link detected: yes
Thanks in Advance
Rob.