Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Avaya Session Manager 6.3, Avaya CM 6.3, SpectraLink 8440, and an FX type Paging Trunk

Status
Not open for further replies.

MylZhI

Technical User
Nov 14, 2013
18
US
Having an odd issue here with a paging trunk and some 8400's. Basically the 8400 is able to dial the TAC and we hear over head the paging tone play. On the Spectralink side however we only hear continuous ring back? Curious if someone has some insight. Trunk configs below



Group Number: 160 Group Type: fx CDR Reports: y
Group Name: Paging BHU C-level COR: 62 TN: 1 TAC: 8160
Direction: outgoing Outgoing Display? y
Dial Access? y Busy Threshold: 255
Queue Length: 0 Country: 1
Comm Type: voice Digit Absorption List:
Prefix-1? y Trunk Flash? n Toll Restricted? n

Trunk Type: loop-start


TRUNK PARAMETERS

Outgoing Dial Type: automatic
Trunk Termination: 600ohm Disconnect Timing(msec): 500

Auto Guard? n Call Still Held? n Sig Bit Inversion: none
Analog Loss Group: 6 Digital Loss Group: 11
Trunk Gain: high

Disconnect Supervision - Out? n
Answer Supervision Timeout: 10 Receive Answer Supervision? y
Administer Timers? y
XOIP Treatment: auto




Group Number: 150 Group Type: sip CDR Reports: y
Group Name: Session Manager COR: 90 TN: 1 TAC: 0150
Direction: two-way Outgoing Display? n
Dial Access? n Night Service:
Queue Length: 0
Service Type: tie Auth Code? n
Member Assignment Method: auto
Signaling Group: 150
Number of Members: 100


TRUNK PARAMETERS

Unicode Name: auto

Redirect On OPTIM Failure: 5000

SCCAN? n Digital Loss Group: 18
Preferred Minimum Session Refresh Interval(sec): 600

Disconnect Supervision - In? y Out? y


XOIP Treatment: auto Delay Call Setup When Accessed Via IGAR? n

TRUNK FEATURES
ACA Assignment? n Measured: both
Maintenance Tests? y



Numbering Format: private
UUI Treatment: service-provider

Replace Restricted Numbers? n
Replace Unavailable Numbers? n


Modify Tandem Calling Number: no




Show ANSWERED BY on Display? y



PROTOCOL VARIATIONS

Mark Users as Phone? n
Prepend '+' to Calling/Alerting/Diverting/Connected Number? n
Send Transferring Party Information? n
Network Call Redirection? n

Send Diversion Header? n
Support Request History? n
Telephone Event Payload Type:


Convert 180 to 183 for Early Media? n
Always Use re-INVITE for Display Updates? n
Identity for Calling Party Display: P-Asserted-Identity
Block Sending Calling Party Location in INVITE? n
Accept Redirect to Blank User Destination? n
Enable Q-SIP? n

Interworking of ISDN Clearing with In-Band Tones: keep-channel-active
 
Post a Session Manager trace. If you can, do an MST trace in CM on your SIP trunk as well if you can - but SM might be enough for now.

To me, it seems like whatever SIP message CM is sending back to your 8400 set once you dial the TAC is not being processed properly by the 8400.

Maybe compare 8400 calling that paging trunk and 8400 calling another phone that answers, look at the last 200OK SM sends that 8400 in each scenario and you might just find there's a tweak on the sig/trunk to make the paging work for you properly.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top