-
1
- #1
glawtonmoore
IS-IT--Management
Does anybody know how to enable automatic telephone relocation?
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations gkittelson on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Automatic Telephone Relocation??? 4
- Thread starter glawtonmoore
- Start date
- Status
-
3
- #2
How do I activate set relocation?
Set relocation allows you to swap two extensions with features and extension numbers (DN's) following the phones. The process depends on whether you have "newer" or "older" programming.
With newer programming, when you enter programming, (feature ** 266344 266344) you will see "Terminals&Sets". Follow these steps (SHOW and NEXT refer to the buttons next to the triangles that appear on the right hand column of buttons on your phone when you enter programming. Programming must be done from a system phone that has three "soft keys" under the display)
1. At “Terminals & Sets” press NEXT until the display reads “System programming”.
2. Press SHOW. The display reads “Hunt Groups”. Press NEXT twice.
3. The display reads “Featr settings”. Press SHOW. Then press NEXT until the display reads “Set relocation:?”. Use CHANGE to toggle Y to move phones, N to turn feature off. Exit programming.
4. Unplug the phone(s) you want to move. Unplug a maximum of two at a time. Plug in the first set you unplugged at the new location. Wait five minutes for the set to “read” its new location, then press Feature *0, and press an intercom button. The display will show the extension number and name. If correct, you may now plug the other phone in to its new location. Wait five minutes to check the status using Feature *0. Deactivate Set Relocation after moving phones.
If you have old software, when you use feature ** 266344 266344, you'll see "a.Configuration". If that is the case:
1. Enter into programming by pressing Feature **266344 266344
2. The display will say “A. Configuration”.
3. Press SHOW. The display reads “1. Line Data”
4. Press NEXT three times. The display reads “4. Miscellaneous”
5. Press SHOW. The display reads “Background music”
6. Press NEXT seven times. The display reads “Set relocation: N”
7. Press the soft key under CHANGE to Y(es)
8. Press Rls to finish.
9. Unplug the phone you want to move. At the new location, unplug the second set if needed. Unplug a maximum of two at a time. Plug in the first set you unplugged at the new location. Wait five minutes for the set to “read” its new location, then press Feature *0, and press an intercom button. The display will show the extension number and name. If correct, you may now plug the other phone in to its new location. Wait five minutes to check the status using Feature *0.
Deactivate Set Relocation after moving phones.
Good Luck!!
Set relocation allows you to swap two extensions with features and extension numbers (DN's) following the phones. The process depends on whether you have "newer" or "older" programming.
With newer programming, when you enter programming, (feature ** 266344 266344) you will see "Terminals&Sets". Follow these steps (SHOW and NEXT refer to the buttons next to the triangles that appear on the right hand column of buttons on your phone when you enter programming. Programming must be done from a system phone that has three "soft keys" under the display)
1. At “Terminals & Sets” press NEXT until the display reads “System programming”.
2. Press SHOW. The display reads “Hunt Groups”. Press NEXT twice.
3. The display reads “Featr settings”. Press SHOW. Then press NEXT until the display reads “Set relocation:?”. Use CHANGE to toggle Y to move phones, N to turn feature off. Exit programming.
4. Unplug the phone(s) you want to move. Unplug a maximum of two at a time. Plug in the first set you unplugged at the new location. Wait five minutes for the set to “read” its new location, then press Feature *0, and press an intercom button. The display will show the extension number and name. If correct, you may now plug the other phone in to its new location. Wait five minutes to check the status using Feature *0. Deactivate Set Relocation after moving phones.
If you have old software, when you use feature ** 266344 266344, you'll see "a.Configuration". If that is the case:
1. Enter into programming by pressing Feature **266344 266344
2. The display will say “A. Configuration”.
3. Press SHOW. The display reads “1. Line Data”
4. Press NEXT three times. The display reads “4. Miscellaneous”
5. Press SHOW. The display reads “Background music”
6. Press NEXT seven times. The display reads “Set relocation: N”
7. Press the soft key under CHANGE to Y(es)
8. Press Rls to finish.
9. Unplug the phone you want to move. At the new location, unplug the second set if needed. Unplug a maximum of two at a time. Plug in the first set you unplugged at the new location. Wait five minutes for the set to “read” its new location, then press Feature *0, and press an intercom button. The display will show the extension number and name. If correct, you may now plug the other phone in to its new location. Wait five minutes to check the status using Feature *0.
Deactivate Set Relocation after moving phones.
Good Luck!!
- Status
Similar threads
