Auto Terminate and LDN's

[ron4ron]

I have a 1000B connected to a 1000M via sip trks. The 1000M has call pilot
with auto attendants and the attendant consoles.

The 1000B has local trunks for out dial . Trouble is,called parties call
the office using the caller ID of the out bound trunks.


REQ: prt
TYPE: rdb
CUST 0
ROUT 0 <--------outbound trunk group

TYPE RDB
CUST 00
DMOD
ROUT 0
DES OUT
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP DTI
ISDN NO
DSEL VOD
PTYP DCO
AUTO NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 16850
CPP NO
TARG 01
CLEN 1
BILN NO
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
OOD 1
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512

IENB 5
TFD 0
LEXT 100
VGD 6
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DRNG NO
CDR YES
INC NO
LAST NO
QREC NO

PAGE 002

OAL YES
AIA NO
OAN YES
OPD YES
CDRX NO
NATL YES
MUS YES
MRT 12
MR NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

What I want to happen is the inbound call on the outbound trunk to go to the auto attendant dn 1937

reading old tek-tips about auto termination , ghtrout said:

"If you _do not_ have an Attendant Console, trunks are _always_ in NITE, so you can just enter the extension at the NITE prompt on the trunk."

so I went into element manager and added 1937 to the nite treatment on those trunks...

REQ: prt
TYPE: tnb
TN 1 7
DATE
PAGE
DES

DES
TN 001 07
TYPE COT
CDEN SD
CUST 0
TRK DTI
PDCA 1
PCML MU
NCOS 0
RTMB 0 1
NITE 1937 <----------
SIGL GRD
SUPN NO
AST NO
IAPG 0
CLS UNR DTN WTA LPR APN THFD
P10 NTC
TKID
AACR NO
DATE 17 MAR 2010


now when I call into the out bound trunks...
it forwards to call pilot saying 1947 does not subscribe to this service. So I look up 1947 and it is an LDN

REQ: prt
TYPE: ldn
TYPE LDN_DATA
CUST 0

TYPE LDN_DATA
CUST 00
OPT XLDN
DLDN NO
LDN0 1947 <---- I tried changing 1947 to 1937 and sch0241
LDN1
LDN2
LDN3
LDN4
LDN5
ICI 00
ICI 01
ICI 02
ICI 03
ICI 04
ICI 05
ICI 06
ICI 07
ICI 08
ICI 09


What must I do to get rout zero to auto terminate to 1937 ?

as always , thanks for your response

 

[PERRYPJ]

You could change AUTO in the RDB to YES, then input 1937 for the ATDN on the trunk TN

OLD ROLMEN WORKING ON NORTELS AND AVAYA

 

[ron4ron]

Will I have to out the trunks and then rebuild them if I do that ?

 

[PERRYPJ]

NO, just change the prompt to YES and the switch will put the ATDN prompt in the Trunk profile. All you have to do is go in and change each trunk for the ATDN

OLD ROLMEN WORKING ON NORTELS AND AVAYA