Audio message on hold

[dabble]

I have a CS1000 at 7.6
I would like to implement on hold messaging.
I have a USB-50 digital audio player that I have connected. Link
I cut off the one end of the audio cable and am using a scotchlock clip with the jumper cables to the bix where the trunk card TN is.

Here is a photo of my connections
Link

The yellow / blue jumper cable is connected to the bix for the trunk card TN.

Below are my PBX configurations for the route and member.
TYPE RDB
CUST 00
ROUT 40
DES MUSIC
TKTP MUS
NPID_TBL_NUM 0
VTRK NO
NODE
CNDP UKWN
ICOG OGT
SRCH LIN
STEP
BDCT NO
ACOD 4041
TARG
CLEN 1
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3

IENB 5
SST 5 0
NEDC ETH
FEDC ORG
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
CDR NO
MUS NO
TTBL 0
OHTD NO
ALRM NO
SGRP 0
ARDN NO
CTBL 0
AACR NO
**************************

TYPE TLST
TKTP MUS
ROUT 40
DES MUSIC
TN 020 0 14 05 MBER 1 MSG ON HOL
***************************

DES MSG ON HOL
TN 020 0 14 05
TYPE MUS
CUST 0
XTRK XUT
TIMP 600
BIMP 600
NMUS NO
RTMB 40 1
CFLP 3
DATE 2 JAN 2015

*****************************

When I dial the access code of 4041, it is just dead air.
I have checked the TGAR and TARG of the phone vs. the route.

Do you think I am trying to do something that isn't possible?

Thanks.

 

[KCFLHRC]

The audio needs to be a 600 ohm input.

 

[KCFLHRC]

Also are you connected to the BK/BL pair of the switch tail for unit 5

 

[KCFLHRC]

Also put a butt set on that pair of wires and see if you hear music.

 

[dabble]

When I put a butt set on the bix on TN 20-0-14-5 I do not hear anything.
How do I determine if the audio is 600ohm and if I am using the BK/BL pair?
Thanks.

 

[KCFLHRC]

First you need to make sure you have music on the end of that jumper wire before you terminate it. If you do then punch it down on the Black/Blue pair of the 25 pair switch tail on your bix block. The black/blue pair is unit 5 of that card if it is an NT8D14.

 

[dabble]

OK yes it is an NT8D14BB card.
So I should be able to put my butt set on the jumper wire with the clips and hopefully hear something.
Is the 600 ohm a PBX thing?

 

[KCFLHRC]

Yes, make sure you hear music on the end of those wires before you punch it down on the bix. The 600 ohm thing should be a non issue, t should work if you hear music on the butt set.

 

[dabble]

OK thanks very much KCFLHRC. I will do this in the morning and post. You have been very helpful.

 

[dabble]

Update - I put the butt set on the two jumper wires - no audio / sound at all.

 

[KCFLHRC]

Then there is a problem with your splice or the music unit