Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

AUD 083

Status
Not open for further replies.

telcomII

Technical User
Jan 28, 2008
18
GB
Can anyone shed a light on why I am getting these audit 083 alarms. The NTP states a wandering message call register. Output: Call register information. I would like to fix the problem but don't know where to begin.

AUD083 072EA1E2 00000C87 00000000 00006FD5 00000000 00000F01 00000000 0000000A 00000023
00000006 00000000 00006FD5 00000000

AUD083 073E2A92 00000C87 00000000 00006FCD 00000000 00000F01 00000000 0000000A 00000023
00000006 00000000 00006FCD 00000000

AUD083 074095B2 00000C87 00000000 00006FBC 00000000 00000F01 00000000 0000000A 00000023
00000006 00000000 00006FBC 00000000

AUD083 0741572C 00000C87 00000000 00006FC4 00000000 00000F01 00000000 0000000A 00000023
00000006 00000000 00006FC4 00000000

AUD083 07422096 00000C87 00000000 00006FBB 00000000 00000F01 00000000 0000000A 00000023
00000006 00000000 00006FBB 00000000

AUD083 07427FD6 00000C87 00000000 00006FC1 00000000 00000F01 00000000 0000000A 00000023
00000006 00000000 00006FC1 00000000

AUD083 0744AE70 00000C87 00000000 00006FD6 00000000 00000F01 00000000 0000000A 00000023
00000006 00000000 00006FD6 00000000

AUD000

DTC001

AUD083 072B626E 00000C87 00000000 00006FDC 00000000 00000F01 00000000 0000000A 00000023
00000006 00000000 00006FDC 00000000

AUD083 07456402 00000C87 00000000 00006FE0 00000000 00000F01 00000000 0000000A 00000023
00000006 00000000 00006FE0 00000000

AUD083 0754BD12 00000C87 00000000 00006FE3 00000000 00000F01 00000000 0000000A 00000023
00000006 00000000 00006FE3 00000000

AUD083 0758086E 00000C87 00000000 00006FDB 00000000 00000F01 00000000 0000000A 00000023
00000006 00000000 00006FDB 00000000

AUD083 075A7192 00000C87 00000000 00006FDD 00000000 00000F01 00000000 0000000A 00000023
00000006 00000000 00006FDD 00000000

AUD000
 
I start with

LD 32
.CONV 0C87

Then disable and renable the TN that outputs (assuming that converts to a TN at all).

I didn't look it up, but that field seems to be the same on all messages you showed us.

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators
 
Thanks for your reply. I used the CONV command to convert the hex to a TN but that TN is unused on a Universal trunk card. Made sure that there was not cross connect on the TN.
 
If the problem persists, build a trunk on it (any kind), then out it right away. That might resolve the prob.

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators
 
00000F01 converts to TN 12 1 0 17. Does that TN mean anything to you in your switch?

War Eagle!
Lions Baseball '09!
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top