On a 406 V2 while attempting to default the security password using this AT command, the system responds with "Polling for S_REC image" I'm expecting a prompt asking for the MAC address of the system. I do get an "OK" after entering the AT command without any parameters. Thanks for any suggestions.
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
AT-SECURITYRESETALL 1
- Thread starter CamIAm
- Start date
hairlessupportmonkey
IS-IT--Management
The MAC should be displayed in your console screen.
type that in first.
type that in first.
-
1
- #3
Reboot the ipo and open hyperterminal or any other terminal.
Type AT-SECURITYRESETALL straight away and nothing else before that.
If that does not work then try this
AT
a-debug
If you get response then reboot again because then it should work.
ACS IP Office or is it ACSS
ACA - Implement IP Telephony -- ACA - Design IP Telephony
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
Type AT-SECURITYRESETALL straight away and nothing else before that.
If that does not work then try this
AT
a-debug
If you get response then reboot again because then it should work.
ACS IP Office or is it ACSS
ACA - Implement IP Telephony -- ACA - Design IP Telephony
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
intrigrant
Systems Engineer
@jamie77, that was the first question that i would ask but you were first.
I bet it is a version below 3.2 and there are no security settings to erase.
I bet it is a version below 3.2 and there are no security settings to erase.
- Thread starter
- #8
mattKnight
Programmer
The first time i tried to carry out this, I couldn't get it to work, because I was hitting the esc key - just like you should to carry out the AT-X erase of firmware and config.
You need to have the system running i.e. fully booted...
Take Care
Matt
I have always wished that my computer would be as easy to use as my telephone.
My wish has come true. I no longer know how to use my telephone.
You need to have the system running i.e. fully booted...
Take Care
Matt
I have always wished that my computer would be as easy to use as my telephone.
My wish has come true. I no longer know how to use my telephone.
CamIAm
defaulting the system will NOT reset the security settings the security settings are also not backed up in the configuration so the only way to reset them is via the DTE port. Keep trying, best to go have a coffee and then come back
Joe W.
FHandw., ACS
insanity is just a state of mind
defaulting the system will NOT reset the security settings the security settings are also not backed up in the configuration so the only way to reset them is via the DTE port. Keep trying, best to go have a coffee and then come back
Joe W.
FHandw., ACS
insanity is just a state of mind
- Thread starter
- #11
Thanks for your posts. I got this to work finally. After entering the "AT-SECURITYRESETALL" command mode and receiving the prompt "Polling for S_Rec Image" I then entered the string: "at+the mac address of the unit (didn't include the highest order octet from the mac address" which reset the security settings to default. Found it here: Thanks to the Russians.......Za zdorovie........
hehe, good job the useful bit of that is in english
ACSS-SME
Get well soon Aaron.
ACSS-SME
Get well soon Aaron.
ThePhoneMn
Vendor
Now I am curious... Anyone have a full set of commands that will work via DTE? I looked at FAQ's and the links provided and do not see options available for AT.
Thanks
Thanks
this shows the dte commands for recovering a unit.
the only other dte commands i know are these for wiping embedded mailboxes etc:
Connect with DTE lead as usual. (Normal Hyperterminal settings also)
AT enter
returns OK
Then AT-DEBUG
returns >hello
IVM-HELP
list of IVM commands eg
IVM-MSG-DEL-ALL ................ Delete all stored messages.
IVM-MBOX-DEL-ALL ................ Delete all mailboxes.
It might be a good idea to collate all the known commands into a new faq
ACSS-SME
Get well soon Aaron.
the only other dte commands i know are these for wiping embedded mailboxes etc:
Connect with DTE lead as usual. (Normal Hyperterminal settings also)
AT enter
returns OK
Then AT-DEBUG
returns >hello
IVM-HELP
list of IVM commands eg
IVM-MSG-DEL-ALL ................ Delete all stored messages.
IVM-MBOX-DEL-ALL ................ Delete all mailboxes.
It might be a good idea to collate all the known commands into a new faq
ACSS-SME
Get well soon Aaron.
ThePhoneMn
Vendor
Lets get some other people involved here. I know there are other AT commands, Avaya had me use them in the past, but I never wrote them down of course.
Anyone have other entries that work with AT?
IPO I&M ACS
Been there, done that
Anyone have other entries that work with AT?
IPO I&M ACS
Been there, done that
This is a very comlete list:
ACS IP Office
APSS IP Office
ACA - Implement IP Telephony -- ACA - Design IP Telephony
APSS UC
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
ACS IP Office
APSS IP Office
ACA - Implement IP Telephony -- ACA - Design IP Telephony
APSS UC
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!
ThePhoneMn
Vendor
That definitely deserves a star! Thank you very much tlpeter
IPO I&M ACS
Been there, done that
IPO I&M ACS
Been there, done that
- Status
Similar threads
- Locked
- Question