Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

ARIA SOHO DEFAULT PASSWORD

Status
Not open for further replies.

Telelogic

Programmer
Jan 19, 2012
10
GR
HI EVERYONE,

I HAVE AN ARIA SOHO (FROM PROMELIT) AND I WOULD LIKE TO CONNECT WITH LDK PCADMIN TO PROGRAM IT.EVEN I TURN DEEPSWITCH AND BATTERY TO DEFAULT THE SYSTEM STILL DON'T ALLOW ME TO CONNECT WITH IT AND TELL'S ME THAT THE PASSWORD IS WRONG.I HAVE TRIED MANY OPTIONS TO CONNECT BUT STILL NOTHING.
IS THERE ANYONE OF YOU,THAT HAVE SEEN THE SAME PROBLEM AND TELL ME HOW TO FIX IT?

THANKS!
 
THE PROBLEM IS NOT IN THE PROGRAM LDK PCADMIN.THE PBX IS THE PROBLEM AND ASKS FOR 4 NUMBERS PASSWORD.USUALLY AFTER CLEARING THE DEFAULT IS NO PASSWORD.
 
STILL THE SAME,I HAVE DONE THESE MANY TIMES BUT NOTHING.7764 NOT MATCHING.ANY PASSWORD FOR SKIP EVERYTHING?
 
I have found the documentation and looked through it.
To reset the Aria Soho set:
SW1: All 4 dip switches -> ON
SW2: Set to OFF
Press SW3 (reset button). Or power off.
Then:
Power on.
SW2: Set to ON.
Try to log on.
Try keyset admin from telephone in position 0 (first extension number) by [Trans/PGM] +*+ # +[Trans/pgm]. Password is none.

If you are using IPLDK PCADMIN you should check the site ini file for the PBX. As you logon in IPLDK PCADMIN you enter Administrator and 0000 to acces the IPLDK PCADMIN program.
For the PBX you need to check the password set for this PBX (Aria Soho).
Try this and report back.

 
How do you connect from the IPLDK PCADMIN to the Aria Soho? Serial or LAN?
 
How to enter the Admin Programming Mode
To enter Admin programming mode, perform the following Steps:
1. Lift the Handset.
OR
1. Press the [MON] button on the Admin Station (By default, station 100).
2. Press the [TRANS/PGM] button and dial * # (a confirmation tone should be heard).
3. Enter the Admin password if the password has been set; a confirmation tone should be heard indicating that the Station is in Admin Programming mode.
4. Each program is accessed by pressing the [TRANS/PGM] button, the following should display:
ENTER PGM NUMBER
5. Dial the desired three-digit program number. If an error is made while entering data, the [TRANS/PGM] button will return to the previous status.

///doktor
 
BECAUSE I HAVE DONE THESE MANY TIMES BEFORE,AS I HAVE PROGRAMMED A LOT OF ARIA SOHO,THIS SYSTEM SEEMS TO BE STUCK FOR A REASON AND THERE NO WAY TO ENDER THE CONFIGURATION MODE FROM LDK PCADMIN OR KEYSET ADMIN.WHEN I PRESS TRANS+*+# THE SYSTEM WAITS A PASSWORD BUT AFTER CLEARING NO PASSWORD NEED.BECAUSE THE SYSTEM IS FROM ITALY,I DONT KNOW IF THERE IS AN ITALY DEFAULT PASS,OR THE SYSTEM IS BROKEN...
(I HAVE TRIED SERIAL,LAN,KEYSET....)
 
I guess that the system is defective if you cannot use keyset admin!

///doktor
 
Can you ping the IP address? (If using IPLDK PC ADMIN)??

///doktor
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top