Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Anybody experience with UILC cards?
- Thread starter frda
- Start date
I have done this several times on an 81C.
Installing a UILC (NT6D71AA in an 81C):
(Reference the Nortel ISDN Basic Rate Interface manual 553-3901-200, page 5 of 234).
(See page 25 of 50 for 110 block layout).
A UILC BRI card places 8 ports on the MDF and uses punch down 0, 2, 4, 6, 8, 10, 12, 14. ----1,3,5,7,9,11,13 are not used.
1. MISP and UILC must be in the same network group (ie. MISP on loop 2, Superloop for IPE on loop 4).
2. Install UILC in any IPE slot, except controller slot.
3. Then configure switch as below (below is a working example used at NAS):
Configure PAD table (optional) if not configured, defaults will be used. Defaults were used at NAS and in the following example.
>ld 73 (Optional)
DDB000
MEM AVAIL: (U/P): 5692260 USED U P: 1495432 267027 TOT: 7454719
DISK SPACE NEEDED: 482 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
REQ prt
TYPE bril
FEAT pad
PDCA
TNLS
PDCA 1
DTI2 PDCA
ONP 17 0
OPX 17 0
DTT 0 0
DCO 0 0
NTC 4 1
TRC 4 1
DTR 0
VNL 4 1
ACO 4 1
AFX 4 1
ADD 4 1
PRI 0 0
DSET 6 0
BRIL 0 0
WRLS 0 0
MEM AVAIL: (U/P): 5692260 USED U P: 1495432 267027 TOT: 7454719
DISK SPACE NEEDED: 482 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
REQ ****
Configure LAPD protocall:
>ld 27
BRI000
MEM AVAIL: (U/P): 5692260 USED U P: 1495432 267027 TOT: 7454719
DISK SPACE NEEDED: 482 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
BRI DSL AVAIL: 49 USED: 1 TOT: 50
LTID AVAIL: 96 USED: 0 TOT: 96
TNS AVAIL: 127 USED: 3373 TOT: 3500
REQ prt
TYPE lapd
PGPN
USER
PGPN 0
LAPD
T200 2
T203 20
N200 3
N201 260
K 1
N2X4 10
#DSL 1
Configure MISP:
REQ prt
TYPE misp
LOOP 2 (This is where the MISP card is slotted)
APPL BRIL
DPSD NO
CARD1 4 0 0
CARD2
CARD3
CARD4
ADDING THE ACTUAL BRI CIRCUIT USES THE FOLLOWING STEPS: 1. ADD a UICL for a line. 2. ADD a DSL for a line. 3. ADD a TSP for a line. The examples below are the actual printouts from NAS.
Add a UICL configured for a line:
REQ prt (new)
TYPE card
TN 4 0 0
MISP 2
CTYP UILC
Add a DSL for a line: (do this for each TN being used)
REQ prt ( enter new if creating a new DSL)
TYPE dsl
TN 4 0 0 0
DES 10AF1
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA (this is the first B-channel)
B2CT VCE DTA (this is the second B-channel)
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 9 JUL 2002
Add a TSP for a line:
REQ prt
TYPE dsl
TN 4 0 0 0
DES 10AF
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 8 NOV 2002
TN 4 0 0 1
DES 10AF
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 8 NOV 2002
TN 4 0 0 2
DES 10AF
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 8 NOV 2002
TN 4 0 0 3
DES 301AF
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 8 NOV 2002
TN 4 0 0 4
DES 301AF
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 8 NOV 2002
TN 4 0 0 5
DES 301AF
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 8 NOV 2002
Add the TSP:
REQ prt (use new if creating tsps)
TYPE tsp
DSL 4 0 0 0
OPT
USID 1
MPHC NO
SPID 78238700101 (2 SPIDS on each TSP) (SPID=Phone# plus 0101) (repeat for each TN to be
78238810101 used. NOTE: the USID increases as each TN is added)
DN 3870 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DN 3881 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DFDN 3870
REQ prt
TYPE tsp
DSL 4 0 0 1
OPT
USID 2
MPHC NO
SPID 78238820101
78238830101
DN 3882 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DN 3883 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DFDN 3882
REQ prt
TYPE tsp
DSL 4 0 0 2
OPT
USID 3
MPHC NO
SPID 78238840101
78238850101
DN 3884 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DN 3885 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DFDN 3884
(Continue until all TSPs needed are added)
Stat the MISP:
>ld 32
NPR000
.stat 2
MISP ( BRIL ) LOOP
00 DSBL 02 BUSY
MISP 2 ENBL ACTIVATED : 07/09/02 13:28
BRIL : ENBL
Stat the UILC:
>ld 32
.stat 4 0 0
SW DSL L2 #TEI L1 D-CHANNEL RCVY CLK MODE
==== ==== ==== ==== ==== ========= ==== ==== ====
00 = IDLE LINE RLS 0 DOWN
01 = UNEQ
02 = UNEQ
03 = UNEQ
04 = UNEQ
05 = UNEQ
06 = UNEQ
07 = UNEQ
.****
Test the ISDN/DSL by connecting an ISDN test set to the TN, enter the spid and dn, then make a voice call.
In the above example the DSL did not work (TEI failure) until the MISP was force downloaded, then the test set was able to place a voice call.
Force download the MISP:
LD 32
.DISL 2
.ENLL 2 FDL (where 2 is the loop # where the MISP card is located).
Mannas
Installing a UILC (NT6D71AA in an 81C):
(Reference the Nortel ISDN Basic Rate Interface manual 553-3901-200, page 5 of 234).
(See page 25 of 50 for 110 block layout).
A UILC BRI card places 8 ports on the MDF and uses punch down 0, 2, 4, 6, 8, 10, 12, 14. ----1,3,5,7,9,11,13 are not used.
1. MISP and UILC must be in the same network group (ie. MISP on loop 2, Superloop for IPE on loop 4).
2. Install UILC in any IPE slot, except controller slot.
3. Then configure switch as below (below is a working example used at NAS):
Configure PAD table (optional) if not configured, defaults will be used. Defaults were used at NAS and in the following example.
>ld 73 (Optional)
DDB000
MEM AVAIL: (U/P): 5692260 USED U P: 1495432 267027 TOT: 7454719
DISK SPACE NEEDED: 482 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
REQ prt
TYPE bril
FEAT pad
PDCA
TNLS
PDCA 1
DTI2 PDCA
ONP 17 0
OPX 17 0
DTT 0 0
DCO 0 0
NTC 4 1
TRC 4 1
DTR 0
VNL 4 1
ACO 4 1
AFX 4 1
ADD 4 1
PRI 0 0
DSET 6 0
BRIL 0 0
WRLS 0 0
MEM AVAIL: (U/P): 5692260 USED U P: 1495432 267027 TOT: 7454719
DISK SPACE NEEDED: 482 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
REQ ****
Configure LAPD protocall:
>ld 27
BRI000
MEM AVAIL: (U/P): 5692260 USED U P: 1495432 267027 TOT: 7454719
DISK SPACE NEEDED: 482 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)
BRI DSL AVAIL: 49 USED: 1 TOT: 50
LTID AVAIL: 96 USED: 0 TOT: 96
TNS AVAIL: 127 USED: 3373 TOT: 3500
REQ prt
TYPE lapd
PGPN
USER
PGPN 0
LAPD
T200 2
T203 20
N200 3
N201 260
K 1
N2X4 10
#DSL 1
Configure MISP:
REQ prt
TYPE misp
LOOP 2 (This is where the MISP card is slotted)
APPL BRIL
DPSD NO
CARD1 4 0 0
CARD2
CARD3
CARD4
ADDING THE ACTUAL BRI CIRCUIT USES THE FOLLOWING STEPS: 1. ADD a UICL for a line. 2. ADD a DSL for a line. 3. ADD a TSP for a line. The examples below are the actual printouts from NAS.
Add a UICL configured for a line:
REQ prt (new)
TYPE card
TN 4 0 0
MISP 2
CTYP UILC
Add a DSL for a line: (do this for each TN being used)
REQ prt ( enter new if creating a new DSL)
TYPE dsl
TN 4 0 0 0
DES 10AF1
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA (this is the first B-channel)
B2CT VCE DTA (this is the second B-channel)
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 9 JUL 2002
Add a TSP for a line:
REQ prt
TYPE dsl
TN 4 0 0 0
DES 10AF
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 8 NOV 2002
TN 4 0 0 1
DES 10AF
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 8 NOV 2002
TN 4 0 0 2
DES 10AF
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 8 NOV 2002
TN 4 0 0 3
DES 301AF
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 8 NOV 2002
TN 4 0 0 4
DES 301AF
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 8 NOV 2002
TN 4 0 0 5
DES 301AF
CUST 0
CTYP UILC
OPT BRIL
MISP 2
B1CT VCE DTA
B2CT VCE DTA
LDN NO
XLST 0
MTEI 8
MCAL 16
MTSP 8
LAPD 0
PRID 1
FDN
EFD
HUNT
EHT
TGAR 0
NCOS 4
SGRP 0
CLS CTD ICDD CDMD ABDD PGND
DATE 8 NOV 2002
Add the TSP:
REQ prt (use new if creating tsps)
TYPE tsp
DSL 4 0 0 0
OPT
USID 1
MPHC NO
SPID 78238700101 (2 SPIDS on each TSP) (SPID=Phone# plus 0101) (repeat for each TN to be
78238810101 used. NOTE: the USID increases as each TN is added)
DN 3870 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DN 3881 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DFDN 3870
REQ prt
TYPE tsp
DSL 4 0 0 1
OPT
USID 2
MPHC NO
SPID 78238820101
78238830101
DN 3882 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DN 3883 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DFDN 3882
REQ prt
TYPE tsp
DSL 4 0 0 2
OPT
USID 3
MPHC NO
SPID 78238840101
78238850101
DN 3884 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DN 3885 0
CT VCE DTA
MCAL 4
CLIP YES
PRES YES
COLP NO
TRANS NO
FEAT HTD FND SFD CFTD MWD FBD CFXD DNO3 DNDY
DFDN 3884
(Continue until all TSPs needed are added)
Stat the MISP:
>ld 32
NPR000
.stat 2
MISP ( BRIL ) LOOP
00 DSBL 02 BUSY
MISP 2 ENBL ACTIVATED : 07/09/02 13:28
BRIL : ENBL
Stat the UILC:
>ld 32
.stat 4 0 0
SW DSL L2 #TEI L1 D-CHANNEL RCVY CLK MODE
==== ==== ==== ==== ==== ========= ==== ==== ====
00 = IDLE LINE RLS 0 DOWN
01 = UNEQ
02 = UNEQ
03 = UNEQ
04 = UNEQ
05 = UNEQ
06 = UNEQ
07 = UNEQ
.****
Test the ISDN/DSL by connecting an ISDN test set to the TN, enter the spid and dn, then make a voice call.
In the above example the DSL did not work (TEI failure) until the MISP was force downloaded, then the test set was able to place a voice call.
Force download the MISP:
LD 32
.DISL 2
.ENLL 2 FDL (where 2 is the loop # where the MISP card is located).
Mannas
- Thread starter
- #3
Hi Mannas,
Thanks for your reply, I'll test it in our lab today, but there is another problem. In our country, the protocol used by the NT1 is 4B3T. Since the UILC only supports 2B1Q, we have to order these NT1's somewhere else. Can you tell me what brand you are using?
Best regards
Frank
Thanks for your reply, I'll test it in our lab today, but there is another problem. In our country, the protocol used by the NT1 is 4B3T. Since the UILC only supports 2B1Q, we have to order these NT1's somewhere else. Can you tell me what brand you are using?
Best regards
Frank
Try sphairon on
But you have to use the meridian modified ones (not phantom powered by the pbx).
But you have to use the meridian modified ones (not phantom powered by the pbx).
- Status
Similar threads
- Question
- Locked
- Question
- Locked
- Question