Any one help US to connect the Second cabinet for 1000S

[JAAGB]

Hi, We are installing 1000E..on that we have to install the second cabinet for the 1000T...can any one give sample configuration for the following plss
IPM
IPR
Host and the IPS

 

[JAAGB]

Main Cabinet
=> prt elnk 0
ACTIVE ETHERNET: "PRIMARY_IP" "192.168.1.131"
INACTIVE ETHERNET: "SECONDARY_ENET" "137.135.128.254"
OK
Second cabinet
=> prt elnk 1
ACTIVE ETHERNET: "CS_ELAN" "192.168.1.135"


=> prt ipm
port IP Address mask autoneg
----------------------------------------------
IPM 1 10.0.1.1 255.255.255.0 ON
IPM 2 10.0.2.1 255.255.255.0 ON
IPM 3 10.0.3.1 255.255.255.0 ON
IPM 4 10.0.4.1 255.255.255.0 ON

=> prt ipr
port MAC address IP Address mask zero bw autoneg
----------------------------------------------------------------------
IPR 1 00:90:cf:06:18:54 10.0.1.2 255.255.255.0 YES ON----Mac of the Port 1 on second cabinet
IPR 2 00:00:00:00:00:00 10.0.2.2 255.255.255.0 YES ON
IPR 3 00:00:00:00:00:00 10.0.3.2 255.255.255.0 NO ON
IPR 4 00:00:00:00:00:00 10.0.4.2 255.255.255.0 NO ON


the Main IP was 192.168.1.131 the second IP was 192.168.1.135

 

[dlesap]

This an example of what you must have configured for an additionnal cabinet on 1000S to run:

=> prt ipm
port IP Address mask autoneg
----------------------------------------------
IPM 1 172.20.21.1 255.255.255.0 ON
IPM 2 172.20.22.1 255.255.255.0 ON
IPM 3 172.20.23.1 255.255.255.0 ON
IPM 4 172.20.24.1 255.255.255.0 ON

=> prt ipr
port MAC address IP Address mask zero bw autoneg
----------------------------------------------------------------------
IPR 1 00:90:cf:06:05:eb 172.20.21.2 255.255.255.0 NO ON
IPR 2 00:00:00:00:00:00 172.20.22.2 255.255.255.0 NO ON
IPR 3 00:90:cf:06:05:bf 172.20.23.2 255.255.255.0 NO ON
IPR 4 00:00:00:00:00:00 172.20.24.2 255.255.255.0 NO ON

=> prt elnk 0
ACTIVE ETHERNET: "CS_ELAN_MAIN" "172.20.0.80"
INACTIVE ETHERNET: "SECONDARY_ENET" "137.135.128.254"
OK

=> prt elnk 1
ACTIVE ETHERNET: "MG1_ELAN_MAIN" "172.20.0.201"

=> prt elnk 3
ACTIVE ETHERNET: "MG3_ELAN_MAIN" "172.20.0.203"

=> prt mask
Call Server/Main Cabinet
SUBNET MASK: "255.255.255.0"
Media Gateway/Expansion Cabinet # 1
SUBNET MASK: "255.255.255.0"

No database file exists for Media Gateway/Expansion Cabinet #2
Media Gateway/Expansion Cabinet # 3
SUBNET MASK: "255.255.255.0"

No database file exists for Media Gateway/Expansion Cabinet #4
OK

=> prt host

Call Server/Main Cabinet
ID Hostname IP Address
1 SECONDARY_ENET 137.135.128.254
2 LOCAL_PPP_IF 137.135.192.4
3 REMOTE_PPP_IF 100.1.1.1
4 CS_ELAN_MAIN 172.20.0.80

Media Gateway/Expansion Cabinet # 1
ID Hostname IP Address
1 MG1_ELAN_MAIN 172.20.0.201


No database file exists for Media Gateway/Expansion Cabinet #2

Media Gateway/Expansion Cabinet # 3
ID Hostname IP Address
1 MG3_ELAN_MAIN 172.20.0.203


No database file exists for Media Gateway/Expansion Cabinet #4
OK

=>prt route

Call Server/Main Cabinet
ID Destination Gateway Port
1 0.0.0.0 172.20.0.254 0

Media Gateway/Expansion Cabinet # 1
ID Destination Gateway Port
1 0.0.0.0 172.20.0.254 0


No database file exists for Media Gateway/Expansion Cabinet #2

Media Gateway/Expansion Cabinet # 3
ID Destination Gateway Port
1 0.0.0.0 172.20.0.254 0


No database file exists for Media Gateway/Expansion Cabinet #4
OK

=>

 

[JAAGB]

hi one small question..while i was loading the second cabinet i gave the ip as 192.168.1.135...but i am not able to ping for the IP...it can be pingable are not..pls reply delsap..thanks for ur help on the prt

 

[JAAGB]

> prt ipm
port IP Address mask autoneg
----------------------------------------------
IPM 1 10.0.1.1 255.255.255.0 ON
IPM 2 10.0.2.1 255.255.255.0 ON
IPM 3 10.0.3.1 255.255.255.0 ON
IPM 4 10.0.4.1 255.255.255.0 ON

=> prt ipr
port MAC address IP Address mask zero bw autoneg
----------------------------------------------------------------------
IPR 1 00:09:cf:06:13:1a 10.0.1.2 255.255.255.0 YES ON
IPR 2 00:00:00:00:00:00 10.0.2.2 255.255.255.0 YES ON
IPR 3 00:00:00:00:00:00 10.0.3.2 255.255.255.0 NO ON
IPR 4 00:00:00:00:00:00 10.0.4.2 255.255.255.0 NO ON


=> prt elnk 0
ACTIVE ETHERNET: "CS_ELAN" "192.168.1.131"
INACTIVE ETHERNET: "SECONDARY_ENET" "137.135.128.254"
OK

=> prt elnk 1
ACTIVE ETHERNET: "MG1_ELAN" "192.168.1.135"

=>


=> prt mask
Call Server/Main Cabinet
SUBNET MASK: "255.255.255.0"
Media Gateway/Expansion Cabinet # 1

No database file exists for Media Gateway/Expansion Cabinet #2

Call Server/Main Cabinet
ID Hostname IP Address
1 LOCAL_PPP_IF 137.135.192.4
2 REMOTE_PPP_IF 100.1.1.1
4 SECONDARY_ENET 137.135.128.254
5 CS_ELAN 192.168.1.131

Media Gateway/Expansion Cabinet # 1
ID Hostname IP Address
2 MG1_ELAN 192.168.1.135


=> prt route

Call Server/Main Cabinet
ID Destination Gateway Port
4 0.0.0.0 192.168.1.254 0

Media Gateway/Expansion Cabinet # 1
ID Destination Gateway Port
2 0.0.0.0 192.168.1.254 0

Please see this is correct

 

[dlesap]

it looks correct.
I'm able to ping my MG:
=> prt elnk 1
ACTIVE ETHERNET: "MG1_ELAN_MAIN" "172.20.0.201"

=> ping 172.20.0.201

PING 172.20.0.201 SUCCESSFUL

Is your cabling correct?
There is 2 LANs. 1 is SLAN connecting both SSC daughterboards. The other is ELAN connecting MG to the same LAN.
Did you check connection recommendations in NTPs?

 

[JAAGB]

yes ia m connected the E-lan from both cabinet in a same switch the Swith light shows on..bur i am not able to ping the second cabinet.
One question i am using the Dummy doungle and loaded the software on it. after install the software i cant access via the TTY.only blank...is it ok?? r we have to put the 1000S doungle and reload the software....pls advice us

 

[dlesap]

Black dongles are use for additionnals cabinets. It's normal you don't have access to TTY after software is loaded. Don't move your Main cabinet dongle!

 

[JAAGB]

really i was confuesed where the problem was...both E-lan are connected and the DB was cross cabled...i am become mad of this prolem

 

[dlesap]

Do you have NTPs for read?
It's 3 CD delivered with Harware, and also accessible on Nortel Website

 

[JAAGB]

yes I have the NTP i am following that only...

pls see the below its coming from the second cabinet TTY message

0x20708200 (tRptD): (7/5/06 16:10:15.026) SRPT1018 STARTUP: unable to send registration request to Call Server/Main Cabinet.

even i am not able to ping the second cabinet from the switch

 

[dlesap]

That message means the new cabinet doesn't see main one.
Is the DB in new cabinet installed in slot 2 (mean you must have LEDs 2 and 4 on in new cabinet) ???

 

[JAAGB]

yes it was on 2 and 4 the 2nd port was connected to the main cabinet.
i am redoing all again will see any good chance

 

[JAAGB]

while loading the software Mr.dlesap did u gave the IP on the new cabinet?
or no ip address atall while loading the software on the new cabinet

 

[JAAGB]

I reloaded the software with out (bootp mode) still its not taking see the errors below.

...0x206ffb4c (tRptD): (7/5/06 16:53:01.496) BUG2263 BOOTP Client: Send BOOTP m
essage failed.
...0x206ffb4c (tRptD): (7/5/06 16:53:18.787) BUG2263 BOOTP Client: Send BOOTP m
essage failed.
...0x206ffb4c (tRptD): (7/5/06 16:53:51.447) BUG2263 BOOTP Client: Send BOOTP m
essage failed.

 

[JAAGB]

Patch 60 has been activated successfully.
0x20700ce4 (tRptD): (7/5/06 17:01:53.324) SRPT730 OS 0: Cold Start
Release: x210400t
Created: Thursday September 16 08:23:35 EDT 2004
Retrieving IP address from Main.
....0x20700ce4 (tRptD): (7/5/06 17:02:41.464) BUG2263 BOOTP Client: Send BOOTP
message failed.
..

 

[JAAGB]

Some good...even bad


ipExpansionStartup - portToUse [2] ipDbNames [ipDB1]
ROUTE HOST TABLE updated: destination[10.0.1.1] gateway[10.0.1.2]
IPDB[2] TX mode
0x20700ce4 (tRptD): (7/5/06 17:45:32.363) SRPT1013 STARTUP: Cabinet 1 registration denied: System IDs did not match.

 

[dlesap]

For new cabinet you received a DB, a dongle and a licence containing the dongle ID. IS it right?

Is that dongle installed on SSC board new cabinet?

Is that black dongle attached to Main site SID in Nortel Web Site or is it attached to another PBX?

I'm not sure a black dongle can be installed on any PBX.

 

[unkalary]

They security dongle for the second cabinet is labeled as REM (meaning REMOTE). The security dongle for the main cable in labeled STD or a standard dongle. If you will look on the security dongle where the ID number is, you will find the STD or REM. The REM must go in the second cabinet SSC card. THE ELAN does not come into efect for the (remote cabinet)IP remote. Only the IP connection coming off the IP expansion daughter board counts. Make sure the MAC address of the remote daughter board is correct when programing the IPR in the Main Cabinet. When connecting with fiber, you must transpose the rec and trans fibers. If you are going through a data network and using CAT 5 patch cords, the IP for the IPR/IPM must be able to be routed. Should also be in a VLAN. The daughter board in the remote cabinet must also be in the bottom position on the SSC card for it to work. Will NOT work in the top position on the SSC card.

Sorry for the long winded reply.