TelecomGuyUT
Programmer
Hey Guys,
We are attempting to route traffic over to a new hosted IVR. The problem that I found in is that the ANI is not coming through with the D-channel messaging. Since the IVR is a shared platform they have to leave the NUM_PLAN as UNKN instead of E.164. Initially, I didn't think that they were sending me ANI at all, but I found the DEBG command in LD 96 and the ANI is being presented.
.enl msgi 29 debg
.enl msgo 29 debg
.
DCH 29 Q931_IMSG SETUP REF 00003580 CH 29 20 TOD 15:21:39 CK 54AAC656
CALLING #:######7565 NUM PLAN: UNKNOWN (Numbers edited with # signs)
CALLED #:###6416 NUM PLAN: E164
STATUS: IN SERVICE
DCH 29 Q931_OMSG STATUS REF 00003580 NCALL TOD 15:21:39 CK 54AAC690
CAUSE: #99 - UNIMPLEMENTED IE
STATE : CALL PRESENT
DCH 29 Q931_OMSG STATUS REF 00003580 NCALL TOD 15:21:39 CK 54AAC6A3
CAUSE: #100 - INVALID IE CONTENTS
STATE : CALL PRESENT
DCH 29 Q931_OMSG CALLPROC REF 00003580 CH 29 20 TOD 15:21:39 CK 54AAC711
DCH 29 Q931_OMSG ALERT REF 00003580 CH 29 20 TOD 15:21:39 CK 54AAC739
PROGRESS: INBAND INFO OR PATTERN IS AVAIL
DCH 29 Q931_IMSG DISC REF 00003580 CH 29 20 TOD 15:21:47 CK 54AB0E6E
CAUSE: #16 - NORMAL CALL CLEARING
In looking through older threads, I'm kind of thinking that I need to modify the RCAP of the DCH but I'm not so sure. This is what I have in the DCH config right now.
ADAN DCH 29
CTYP TMDI
MG_CARD 004 0 02
PORT 1
DES XO_LD
USR PRI
DCHL 29
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP NDS
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO
If anyone has run into a similar situation and came out with the upper-hand I would appreciate any assistance.
Thanks,
--
We are attempting to route traffic over to a new hosted IVR. The problem that I found in is that the ANI is not coming through with the D-channel messaging. Since the IVR is a shared platform they have to leave the NUM_PLAN as UNKN instead of E.164. Initially, I didn't think that they were sending me ANI at all, but I found the DEBG command in LD 96 and the ANI is being presented.
.enl msgi 29 debg
.enl msgo 29 debg
.
DCH 29 Q931_IMSG SETUP REF 00003580 CH 29 20 TOD 15:21:39 CK 54AAC656
CALLING #:######7565 NUM PLAN: UNKNOWN (Numbers edited with # signs)
CALLED #:###6416 NUM PLAN: E164
STATUS: IN SERVICE
DCH 29 Q931_OMSG STATUS REF 00003580 NCALL TOD 15:21:39 CK 54AAC690
CAUSE: #99 - UNIMPLEMENTED IE
STATE : CALL PRESENT
DCH 29 Q931_OMSG STATUS REF 00003580 NCALL TOD 15:21:39 CK 54AAC6A3
CAUSE: #100 - INVALID IE CONTENTS
STATE : CALL PRESENT
DCH 29 Q931_OMSG CALLPROC REF 00003580 CH 29 20 TOD 15:21:39 CK 54AAC711
DCH 29 Q931_OMSG ALERT REF 00003580 CH 29 20 TOD 15:21:39 CK 54AAC739
PROGRESS: INBAND INFO OR PATTERN IS AVAIL
DCH 29 Q931_IMSG DISC REF 00003580 CH 29 20 TOD 15:21:47 CK 54AB0E6E
CAUSE: #16 - NORMAL CALL CLEARING
In looking through older threads, I'm kind of thinking that I need to modify the RCAP of the DCH but I'm not so sure. This is what I have in the DCH config right now.
ADAN DCH 29
CTYP TMDI
MG_CARD 004 0 02
PORT 1
DES XO_LD
USR PRI
DCHL 29
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID **
RCAP COLP NDS
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO
If anyone has run into a similar situation and came out with the upper-hand I would appreciate any assistance.
Thanks,
--