Alternate routing not working.

[lancbomb]

Hi,

Have a prob with alternate routing,

LIM1 = 01895 area
LIM2 = 01865 area

ROU1 = DASS (01895)
ROU4 = DASS (01865)
ROU2 = ANA (01895)

Routes so that LIM1, = rou1, rou4, rou2
LIM2, = rou4, rou1, rou2

If LIM1's DASS goes down, second and third rou, apparently works
If LIM2's DASS does down, 2nd and 3rd choice, def dont work.

LIM1 is main site so is generally bomb proof.

below is print out (BC10) any ideas, cheers
-------------------------------------------

<NADAP;
NUMBER ANALYSIS DATA
TYPE OF SERIES NUMBER SERIES
EXTERNAL DESTINATION CODE 77
781 - 786
79
LCR ACCESS
CODE NUMBER SERIES 9
EXTERNAL NUMBER LENGTH DATA
EXTERNAL NUMBER NUMBER LENGTH
71 2 - 20
72 2 - 6
73 2 - 20
76 2 - 20
77 2 - 20
78 2 - 20
79 2 - 20
9 2 - 20

<RODDPEST=ALL;
EXTERNAL DESTINATION ROUTE DATA
DEST ROU CHO ADC TRC SRT NUMACK
781 1 0005000000000250000 0 4 0
4 1 0005000000000250000 0 4 0
2 2 0005000000000250000 0 4 0
782 4 0005000000000250000 0 4 0
1 1 0005000000000250000 0 4 0
2 2 0005000000000250000 0 4 0

END

<LCDDP:TAB=DNT1;
NOT ACCEPTED
ENTRY NOT FOUND

<LCDDP:TAB=DNT2;
NOT ACCEPTED
ENTRY NOT FOUND

<LCLDP:LIM=ALL;
LEAST COST LIM DATA
LIM AC DEST
1 01895 781
2 01865 782
END

<ROCAP:ROU=1&4&2;
ROUTE CATEGORY DATA
ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP
1 013000000000001 5 2100030001 0 30 128 00151510 111100000020 001100
4 011000000000001 5 2100030000 0 30 128 00151510 111100000020 001100
2 013000000000001 3 2100030000 0 15 128 00151510 111100000000 001100

END

<RODAP:ROU=1&4&2;
ROUTE DATA
ROU TYPE VARC VARI VARO FILTER
1 TL50 H'0000000C H'00000000 H'00000000 NO
4 TL50 H'0000000C H'00000000 H'00000000 NO
2 TL1 H'00000201 H'00000002 H'00000009 NO

END

<RODNP:ROU=ALL;
NOT ACCEPTED
DAY AND NIG
NOT ASSIGNED

 

[rfpui]

Hi
Now I analyze your’ printout and find one difference between ROU 1 and 4
It is position D3 in SEL by ROCAP, try to set D3=3 in ROU =4

And probably you want send RONDP:ROU=ALL; and not RODNP:ROU=ALL;

 

[lancbomb]

Hi RFPUI,

re: D3 in sel
1 Sequential selection
(Even seizure in own LIM and after that the same principle in the next LIM)

3 Sequential selection in route.
(First free external line in route. Selection always starts with the same line.)


I dont see how that fixes it,

RONDP print has no entries, however.....

some testing shows, that selecting the dest codes, to other site works. also blocking rou4 will force calls to rou1.

BUT, and this is the case, I dont know if the situation when the links fallen over gives a IDLE and FREE in the SUSIP print, will then route the calls, as the MD thinks its up ?

I know IDLE and BUSY does work though...

will continue looking, any further ideas ?

cheers