Adding new DIU2U-M Cards to Hipath4K V2

[jnzy111]

Hello,

We are looking at increasing our capacity with 2 more T1 lines and have already installed the cards but I do not see them when doing a dis-bcsu:tbl;

< <dis-bcsu:tbl;
DIS-BCSU:TBL;
H500: AMO BCSU STARTED

ADDRESS : LTG 1 LTU 1 SOURCE GROUP 1
-----+-----------+---------+---+---+-+------------+-----+--------+------------+
| ASSIGNED | MODULE |FCT|HWY| | INSERTED | | | MODULE |
PEN | MODULE | TYPE |ID |BDL| | MODULE |STATE| HW-INFO| STATUS |
-----+-----------+---------+---+---+-+------------+-----+--------+------------+
1 | Q2316-X STMI2HFA 3 A | | Q2316-X | 1 | -07 - | READY |
2 | Q2246-X SLMA24 A | | Q2246-X | 1 | -10 - | READY |
3 | Q2216-X DIU2U-M 6 A | | Q2216-X | 1 | -06 - | READY |
4 | Q2468-X RG-USA | | Q2468-X | 1 | - | READY |
5 | AVAILABLE | | AVAILABLE | | | |
6 | AVAILABLE | | AVAILABLE | | | |
7 | Q2266-X LTUCA | | Q2266-X | 1 | -12 - | READY |
8 | Q2246-X SLMA24 A | | Q2246-X | 1 | -05 - | READY |
9 | Q2246-X SLMA24 A | | Q2246-X | 1 | -05 - | READY |
10 | Q2485-X TMC16P A | | Q2485-X | 1 | D429-B | READY |
11 | AVAILABLE | | AVAILABLE | | | |
12 | Q2168-X SLMO24 1 A | | Q2168-X | 1 | -11 - | READY |
13 | Q2216-X DIU2U-M 6 A | | Q2216-X | 1 | -06 - | READY |
14 | Q2246-X SLMA24 A | | Q2246-X | 1 | -10 - | READY |

ADDRESS : LTG 1 LTU 2 SOURCE GROUP 1
-----+-----------+---------+---+---+-+------------+-----+--------+------------+
| ASSIGNED | MODULE |FCT|HWY| | INSERTED | | | MODULE |
PEN | MODULE | TYPE |ID |BDL| | MODULE |STATE| HW-INFO| STATUS |
-----+-----------+---------+---+---+-+------------+-----+--------+------------+
1 | Q2316-X STMI2HFA 3 A | | Q2316-X | 1 | -05 - | READY |
2 | Q2246-X SLMA24 A | | Q2246-X | 1 | -10 - | READY |
3 | Q2216-X DIU2U-M 6 A | | Q2216-X | 1 | -06 - | READY |
4 | AVAILABLE | | AVAILABLE | | | |
5 | AVAILABLE | | AVAILABLE | | | |
6 | AVAILABLE | | AVAILABLE | | | |
7 | Q2266-X LTUCA | | Q2266-X | 1 | -12 - | READY |
8 | AVAILABLE | | AVAILABLE | | | |
9 | Q2216-X DIU2U-M 6 A | | Q2216-X | 1 | -06 - | READY |
10 | AVAILABLE | | AVAILABLE | | | |
11 | AVAILABLE | | AVAILABLE | | | |
12 | Q2468-X RG-USA | | Q2468-X | 1 | - | READY |
13 | Q2216-X DIU2U-B 5 A | | Q2216-X | 1 | -06 - | READY |
14 | Q2316-X STMI2 1 A | | Q2316-X | 1 | -07 - | READY |
+-----------------------------+-+------------+-----+--------+------------+
| IP ADDRESS : 172. 19.171.195 B-CHANNELS : 60 BCHLCNT : 30 |
+-----------------------------+-+------------+-----+--------+------------+


The new cards should show up in 1-1-5 and 1-2-5 respectively, however they don't show up at all.

Is there another command for them to be recognized?

Thanks in advance!

---Mike

 

[Iamnothere]

Did you build TDCSU yet? If this new board will use the same COT/COP, trunk group, etc, as the other DIU2U boards, then you can simply modify the PEN in a REGEN-TDCSU command. But first verify that your trunk group (BUEND) is large enough to accommodate the extra channels.

 

[donb01]

This is just a question as I learn about the 4000. Don't you have to add the part numbers of the boards into BCSU first like you do on 9006? Or does TDCSU do that?

 

[jnzy111]

I checked the trunk group and looks like it can max at 60, see output below..

Next question I have is when I do the Regen, REGEN-TDCS will it disrupt the switch or users at all??? If so then I would have to schedule after hours...


DISPLAY COMPLETED;
<dis-buend:all;
M33: VALUE TYPE DOES NOT CORRESPOND TO TYPE IN VALUE TABLE
TGRP = 16
FORMAT =
DIS-BUEND:16,;
H500: AMO BUEND STARTED

+------------------------------- FORMAT = L -----------------------------------+
| TGRP NUMBER : 16 TGRP NAME : SJC CONF SERVER MAXIMUM NO. : 60 |
| CHARCON : NEUTRAL |
| SUBGROUP NO.: 28 DEVICE TYPE : S1CONN TRACENO : 0 |
| SEARCH MODE : CIRCULAR ACD THRESHOLD : * |
| NUMBER OF ASSOCIATED ROUTES : 2 PRIORITY : 2 |
| TDDRFLAG : ON TDDRTHRESHOLD: 2 SOURCEGROUPIDX : 1 |
| GDTRRULE : 0 ACDPMGRP : 0 |
| THE FOLLOWING TRUNKS (LTG-LTU-SLOT-CCT) HAVE BEEN ALLOCATED: |
+------------------------------------------------------------------------------+
| 1- 2- 9-1 1 | 1- 2- 9-1 2 | 1- 2- 9-1 3 |
| 1- 2- 9-1 4 | 1- 2- 9-1 5 | 1- 2- 9-1 6 |
| 1- 2- 9-1 7 | 1- 2- 9-1 8 | 1- 2- 9-1 9 |
| 1- 2- 9-1 10 | 1- 2- 9-1 11 | 1- 2- 9-1 12 |
| 1- 2- 9-1 13 | 1- 2- 9-1 14 | 1- 2- 9-1 15 |
| 1- 2- 9-1 16 | 1- 2- 9-1 17 | 1- 2- 9-1 18 |
| 1- 2- 9-1 19 | 1- 2- 9-1 20 | 1- 2- 9-1 21 |
| 1- 2- 9-1 22 | 1- 2- 9-1 23 | |
+------------------------------------------------------------------------------+

AMO-BUEND-111 TRUNK GROUP
DISPLAY COMPLETED;
<

 

[Iamnothere]

REG-TDCSU will not disrupt anything. It merely displays the entire AMO necessary to rebuild the trunk circuit(s).

You did perform ADD-BCSU, correct? The boards do not automatically populate the BCSU hardware table. If you are not familiar with that process, then perform REGEN-BCSU; and you will see how to add a trunk board.