ACOD on Option61 and Cisco IP router

[RV482]

Hi!,

We have an existing Option61 (not C or CS), and it's interfaced with an existing Cisco router through E1/R2 using an ACODXXXX so users can call the IP phones.

We have a another Cisco router and again planning to interface it with the Option61 thru another E1/R2, is there a possiblity to use just 1 (one) ACODXXXX for the 2 (two) IP routers so users from the Nortel wouldn't have to use 2 (two) access codes?

Also, if this is possible, can we split the E1/R2 30 channels on the Nortel to use 15 channels for the existing IP router and the other 15 channel for the new IP router?

Thanks!

 

[Firebird Scrambler]

The access code "ACOD" you have mentioned, is linked only to the RDB in LD 16 for the existing Cisco trunks. The existing trunks can be assigned to different RDB's but they would have different ACOD's.

The problem would be connecting to different routers on the same Nortel card.

As for using just the one access code, the easiest way is to change the existing ACOD to a different number and then creating a new RLB in LD 86 with the Cisco designated RDB's in different entries and then in LD 87 to create a new CDP entry either a TSC or a DSC of the original ACOD and placing the newly added RLB in that entry.


Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website =

http://somertel.com

linkedin

 

[RV482]

Thanks so much for the quick help.

In this case we will be using 2 (two) E1/R2 card, will the 1 (one) ACOD procedure be the same?

Again.. thanks!

 

[Firebird Scrambler]

Yes, a steering code entry can be assigned to route to a RLB in LD 86. The RLI can have loads of different routes, all in a different entry. The routes can be using different protocols such as ISDN, COT, etc.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website =

http://somertel.com

linkedin

 

[RV482]

Hi!

We finally had approval to test the connection, just to reconfirm, attached is the setup we are about to do.

Any comments?

Thanks!

 

[Firebird Scrambler]

From looking at the power point presentation, it appears OK. I'm not that up to date with the PRI card you are using, but the programming looks to be OK.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website =

http://somertel.com

linkedin

 

[RV482]

Thank you for the very prompt reply.

Your assistance is very much appreciated.

I'll inform you of the result.

Thanks again!

 

[RV482]

Hi!

The Pri/Cisco procedure was pushed but we are having this issue.. any comment?

Thanks!

Loop 28
stat 29

PRI2 LOOP 29 - ENBL
REF CLK: DSBL
SERVICE RESTORE: YES
ALARM STATUS: ACCEPTABLE
CH 01 - BUSY TIE * CH 02 - IDLE TIE *
CH 03 - IDLE TIE * CH 04 - IDLE TIE *
CH 05 - IDLE TIE * CH 06 - IDLE TIE *
CH 07 - IDLE TIE * CH 08 - IDLE TIE *
CH 09 - IDLE TIE * CH 10 - IDLE TIE *
CH 11 - IDLE TIE * CH 12 - IDLE TIE *
CH 13 - IDLE TIE * CH 14 - IDLE TIE *
CH 15 - IDLE TIE * CH 16 - IDLE TIE *
CH 17 - IDLE TIE * CH 18 - IDLE TIE *
CH 19 - IDLE TIE * CH 20 - IDLE TIE *
CH 21 - IDLE TIE * CH 22 - IDLE TIE *
CH 23 - IDLE TIE * CH 24 - IDLE TIE *
CH 25 - IDLE TIE * CH 26 - IDLE TIE *
CH 27 - BUSY TIE * CH 28 - BUSY TIE *
CH 29 - IDLE TIE * CH 30 - BUSY TIE *
CH 31 - DCH 9
.stat 28


PRI2 LOOP 28 - ENBL
REF CLK: DSBL
SERVICE RESTORE: YES
ALARM STATUS: OOS LOCAL ALARM : LOS
CH 01 - DSBL TIE * CH 02 - DSBL TIE *
CH 03 - DSBL TIE * CH 04 - DSBL TIE *
CH 05 - DSBL TIE * CH 06 - DSBL TIE *
CH 07 - DSBL TIE * CH 08 - DSBL TIE *
CH 09 - DSBL TIE * CH 10 - DSBL TIE *
CH 11 - DSBL TIE * CH 12 - DSBL TIE *
CH 13 - DSBL TIE * CH 14 - DSBL TIE *
CH 15 - DSBL TIE * CH 16 - DSBL TIE *
CH 17 - DSBL TIE * CH 18 - DSBL TIE *
CH 19 - DSBL TIE * CH 20 - DSBL TIE *
CH 21 - DSBL TIE * CH 22 - DSBL TIE *
CH 23 - DSBL TIE * CH 24 - DSBL TIE *
CH 25 - DSBL TIE * CH 26 - DSBL TIE *
CH 27 - DSBL TIE * CH 28 - DSBL TIE *
CH 29 - DSBL TIE * CH 30 - DSBL TIE *
CH 31 - DCH 10
.
S 092 00 A008 001 1105 10/05 15:58 00:00:18 C 0081463248334
****

.
DTA106 28
DTA203 28 4 2
DTA203 28 4 1


DTI000
.**
DT*A112 28 LS *

 

[RV482]

Additional info.. cannot enable MSDL in Ld96 /ld 48... thanks!
OVL000
>ld 96

DCH000
.stat msdl
MSDL 14: SYS DSBL - NOT RESPONDING
MSDL 15: ENBL
.enl msdl 14 fld
MSDL018
.enll msdl 14

DCH009
.enll msdl 14

DCH009
.****

OVL000
>ld 489

OVL014
>ld 48

LNK000
.stat msdl

MSDL 14: SYS DSBL - NOT RESPONDING
MSDL 15: ENBL
.enl msdl
N 114 00 A023 001 3238 10/05 16:06 00:01:10
14

MSDL006
.enl msdl 14 fdl

MSDL006
.

LNK000
.*
.*
.*
.*

OVL000
>logo

ssck 0

ENBL
CLOCK ACTIVE
SYSTEM CLOCK - FREE RUN
PREF - 0
SREF - 1
AUTO SWREF CLK - ENBL
NO ERROR
.enl cc 0