Accelar 1200 Password Recovery

[Morvac]

Purchased a Accelar from eBay to setup a home network for training. I've read stories on here about some difficulties on resetting some of Bay's other hardware - does the same hold true with the Accelar? I'm needing to reset this to factory defaults....any ideas?

Thanks in advance!

 

[jimbopalmer]

Narnian  posted this:
Passport 1000 Password Recovery
There is no known backdoor password for the Passport 1000 CPU modules. In order to access a CPU when the password is not known, you must factory default the box. For this reason, it is advisable to save the output from "show config" and save it to a PCMCIA card or your computer. The "show config" output will contain the passwords in plain-text format, and the config information in this file can be input back to the CPU after a factory default.
Connect to the console port on the 1297 or 1298 CPU module.
Reset the CPU.
Enter monitor mode.
Type: config sys set flags factorydefault true
Type: save config
Type: reset
Allow the CPU to completely boot to the banner login screen.
Login with the username 'rwa' and a password of 'rwa'
Type: config sys set flags factorydefault false
Type: save config
The Passport 1000 is now defaulted. If you have a previously saved file with the output from "show config," you may re-enter your config information from that fil

tcaddoo comments on the above:
You have to go into monitor mode and type flags.  At this point, it will walk you through 5 questions, one of which is whether to use factory defaults or not.

I tried to remain child-like, all I acheived was childish.

 

[Morvac]

I tried the method listed...however after I enter:

Type: config sys set flags factorydefault true
Type: save config
Type: reset

Login: rwa
Password: ***

I get this:

[12/22/2003 00:53:36] WARNING Code=0x1ff0009 Task=tShell Blocked unauthorized c
li access
Login: [12/22/2003 00:53:40] Sending Cold-Start Trap


Any ideas?

 

[Morvac]

More info: Am I doing something wrong to get this password reset??

--------------------------------------------------

Accelar Monitor v1.3.5

CPU: 60Mhz PPC 403GCX Type 2 Rev 1 in Slot 4
DRAM: 32M
Chassis: 1200
Reason for Last Reset: WDT
Slot 1 is occupied
Slot 2 is occupied
Slot 3 is occupied
Slot 6 is occupied
Slot 7 is occupied
Slot 8 is occupied
Power supply 2 fault

Press any key to stop autoboot

monitor>

Accelar Monitor v1.3.5

CPU: 60Mhz PPC 403GCX Type 2 Rev 1 in Slot 4
DRAM: 32M
Chassis: 1200
Reason for Last Reset: PWR/BUTTON/SOFT
Slot 1 is occupied
Slot 2 is occupied
Slot 3 is occupied
Slot 6 is occupied
Slot 7 is occupied
Slot 8 is occupied
Power supply 2 fault

Press any key to stop autoboot

monitor> config sys set flags factorydefault true
monitor> save config
boot configuration has been saved
ip configuration has been saved
monitor> resetÿ

Accelar Monitor v1.3.5

CPU: 60Mhz PPC 403GCX Type 2 Rev 1 in Slot 4
DRAM: 32M
Chassis: 1200
Reason for Last Reset: PWR/BUTTON/SOFT
Slot 1 is occupied
Slot 2 is occupied
Slot 3 is occupied
Slot 6 is occupied
Slot 7 is occupied
Slot 8 is occupied
Power supply 2 fault

Press any key to stop autoboot
Checking system DRAM
Bank 5 (DRAM): 16 MB Addr: 0x01000000
Bank 7 (DRAM): 16 MB Addr: 0x00000000
Installed DRAM: 32 MB
Checking DRAM between 0x80000000 and 0x82000000
80030000
System DRAM Test terminated by user
System DRAM Check complete
User Selected Boot Sources
Primary = flash:acc2.0.7.0
Secondary = pcmcia:acc2.0.7.0
Tertiary = none
Config = nvram
Booting from [flash:acc2.0.7.0] on-board flash memory
Configuration from [nvram] ...
Unzipping file acc2.0.7.0
Details /projects/first/rel2.0/rel2.0.7.0/main/hw/acc2.0.7.0.st on Mon Mar 27 13
:00:09 PST 2000
from 0x761b00b0 to 0x80010000 1887956 to 8388608 bytes
Attaching network interface nicEvb0... done.
Null 0.0.0.0 inet address for interface nicEvb.
Attaching network interface lo0... done.


Accelar System Software Release 2.0.7.0
Copyright (c) 1996-1999 Bay Networks, Inc.

[000 00:00:00:633] INTERPRET FOLLOWING TIMESTAMPS AS TIME SINCE BOOT
[000 00:00:00:900] System boot
[000 00:00:01:166] Accelar System Software Release 2.0.7.0
[000 00:00:01:433] System log file flash:syslog:0:48
[000 00:00:03:100] INTERPRET FOLLOWING TIMESTAMPS AS ACTUAL DATES
[12/22/2003 00:52:41] Card Inserted: Slot#=1, Serial#=3A26M, Version=v1.0
[12/22/2003 00:52:42] Card Inserted: Slot#=2, Serial#=3A20G, Version=v1.0
[12/22/2003 00:52:43] Card Inserted: Slot#=3, Serial#=3A1XV, Version=v1.0
[12/22/2003 00:52:44] Card Inserted: Slot#=6, Serial#=2A5BD, Version=v4.0
[12/22/2003 00:52:45] Card Inserted: Slot#=7, Serial#=2A4DL, Version=v4.0
[12/22/2003 00:52:46] Card Inserted: Slot#=8, Serial#=HA2KO, Version=v4.0

** Loading configuration from nvram **

Initializing card in slot #1 ... OK
Initializing card in slot #2 ... OK
Initializing card in slot #3 ... OK
Initializing card in slot #6 ... OK
Initializing card in slot #7 ... OK
Initializing card in slot #8 ... OK

[12/22/2003 00:52:56] Global filters are not supported in this release.

[12/22/2003 00:52:56] System is ready

********************************
* Bay Networks,Inc. *
* Copyright (c) 1996-1999 *
* All Rights Reserved *
* Accelar 1200 *
* Software Release 2.0.7.0 *
********************************

Login: rwa
Password: ***
[12/22/2003 00:53:36] WARNING Code=0x1ff0009 Task=tShell Blocked unauthorized c
li access
Login: [12/22/2003 00:53:40] Sending Cold-Start Trap

 

[GTomte]

It says ** Loading configuration from nvram **, and therefore the configuration is not factory default.

Try "boot" instead of "reset" after the "save" command.

Regards
G. Tomte

- Nortel Networks, Routers, switches
- Alteon
- CacheFlow
- Blue Coat

 

[Morvac]

I've tried both the rwa/rwa and the secret/secret username/password combinations as well as the 'boot' instead of 'reset'. Maybe it isn't saving correctly?? The output is listed below as everyone can see.


Accelar Monitor v2.0.1

CPU: 60Mhz PPC 403GCX Type 2 Rev 1 in Slot 5
DRAM: 32M
Chassis: 1200
Reason for Last Reset: WDT
Slot 1 is occupied
Slot 2 is occupied
Slot 3 is occupied
Slot 6 is occupied
Slot 7 is occupied
Slot 8 is occupied
Power supply 2 fault

Press any key to stop autoboot

monitor> config sys set flags factorydefault true
monitor> save config
boot configuration has been saved
ip configuration has been saved
monitor> boot
Checking system DRAM
Bank 5 (DRAM): 16 MB Addr: 0x01000000
Bank 7 (DRAM): 16 MB Addr: 0x00000000
Installed DRAM: 32 MB
Checking DRAM between 0x80000000 and 0x82000000
82000000
System DRAM Check complete
User Selected Boot Sources
Primary = flash:acc2.0.7.0
Secondary = pcmcia:acc2.0.7.0
Tertiary = none
Config = nvram
Booting from [flash:acc2.0.7.0] on-board flash memory
Configuration from [nvram] ...
Unzipping file acc2.0.7.0
Details /projects/first/rel2.0/rel2.0.7.0/main/hw/acc2.0.7.0.st on Mon Mar 27 13
:00:09 PST 2000
from 0x761b00b0 to 0x80010000 1887956 to 9358964 bytes
Attaching network interface nicEvb0... done.
Attaching network interface lo0... done.


Accelar System Software Release 2.0.7.0
Copyright (c) 1996-1999 Bay Networks, Inc.

[000 00:00:00:633] INTERPRET FOLLOWING TIMESTAMPS AS TIME SINCE BOOT
[000 00:00:00:900] System boot
[000 00:00:01:166] Accelar System Software Release 2.0.7.0
[000 00:00:01:433] System log file flash:syslog:1:183
[000 00:00:04:100] INTERPRET FOLLOWING TIMESTAMPS AS ACTUAL DATES
[01/05/2004 21:48:49] Card Inserted: Slot#=1, Serial#=3A26M, Version=v1.0
[01/05/2004 21:48:50] Card Inserted: Slot#=2, Serial#=3A20G, Version=v1.0
[01/05/2004 21:48:51] Card Inserted: Slot#=3, Serial#=3A1XV, Version=v1.0
[01/05/2004 21:48:52] Card Inserted: Slot#=6, Serial#=2A5BD, Version=v4.0
[01/05/2004 21:48:53] Card Inserted: Slot#=7, Serial#=2A4DL, Version=v4.0
[01/05/2004 21:48:55] Card Inserted: Slot#=8, Serial#=HA2KO, Version=v4.0

** Loading configuration from nvram **

Initializing card in slot #1 ... OK
Initializing card in slot #2 ... OK
Initializing card in slot #3 ... OK
Initializing card in slot #6 ... [01/05/2004 21:49:59] Card Inserted: Slot#=4,
Serial#=unknown, Version=unknown Dormant CPU
OK
Initializing card in slot #7 ... OK
Initializing card in slot #8 ... OK

[01/05/2004 21:49:05] Global filters are not supported in this release.

[01/05/2004 21:49:05] System is ready

********************************
* Bay Networks,Inc. *
* Copyright (c) 1996-1999 *
* All Rights Reserved *
* Accelar 1200 *
* Software Release 2.0.7.0 *
********************************

Login: rwa
Password: ***
[01/05/2004 21:49:21] WARNING Code=0x1ff0009 Task=tShell Blocked unauthorized c
li access
Login: secret
Password: ******
[01/05/2004 21:49:28] WARNING Code=0x1ff0009 Task=tShell Blocked unauthorized c
li access
Login:

===================================================================

Other info:
monitor> show
User Selected Boot Sources
---------------------------
Primary = flash:acc2.0.7.0
Secondary = pcmcia:acc2.0.7.0
Tertiary = none
Config = nvram
Autoboot is enabled
Factory defaults is disabled <<< ---------- Does this need to change? How if what I am doing is correct?
Switch port isolation is disabled
---------------------------
press any key to continue
Boot Devices:
------------------------------------------------------------------
0 Enabled System Memory [dram] addr:0x0 sz:0x2000000
1 Enabled on-board flash memory [flash]
vendor:sharp_28f016su sz:0x400000 bsz:0x10000
2 Enabled pcmcia flash memory [pcmcia]
vendor:unknown sz:0x0 bsz:0x20000
4 Enabled Serial Port 2 [s2] hw=ff:ff:ff:ff:ff:ff
ip=10.100.1.5 netmask=0xffffff00
mgmt net=0.0.0.0 gateway=10.100.1.3
5 Enabled Debug Ethernet [nic] hw=00:e0:16:6f:ee:00
ip=10.100.1.6 netmask=0xffffff00
mgmt net=0.0.0.0 gateway=10.100.1.3
------------------------------------------------------------------
press any key to continue
Boot-up Test Devices:
---------------------------------------
0 Enabled System Memory [dram]
4 Enabled Serial Port 2 [s2]
5 Enabled Debug Ethernet [nic]
---------------------------------------
press any key to continue
Net Devices:
----------------------------------------------------------------
4 Enabled Serial Port 2 [s2] hw=ff:ff:ff:ff:ff:ff
ip=10.100.1.5 netmask=0xffffff00
mgmt net=0.0.0.0 gateway=10.100.1.3
5 Enabled Debug Ethernet [nic] hw=00:e0:16:6f:ee:00
ip=10.100.1.6 netmask=0xffffff00
mgmt net=0.0.0.0 gateway=10.100.1.3
----------------------------------------------------------------
press any key to continue
TFTP Information:
---------------------------------------
Server=0.0.0.0
File=/
---------------------------------------
press any key to continue
Environmental Information:
---------------------------------------

CPU: 60Mhz PPC 403GCX Type 2 Rev 1 in Slot 5
DRAM: 32M
Chassis: 1200
Reason for Last Reset: WDT
Slot 1 is occupied
Slot 2 is occupied
Slot 3 is occupied
Slot 6 is occupied
Slot 7 is occupied
Slot 8 is occupied
Power supply 2 fault
---------------------------------------
monitor> dir
Device: flash
FN Name Flags Length
-- ---- ----- ------
1 acc1.3.6 DXZN 1395137
2 accboot1.3.5 DXZN 88634
3 config DCN 16588
4 syslog LN 131072
5 acc2.0.7.0 XZN 1888132
-- ------
5 files bytes used= 3670016 free=524288

Device: pcmcia
FN Name Flags Length
-- ---- ----- ------
-- ------
0 files bytes used= 0 free=4194304

monitor>


THANKS FOR THE HELP EVERYONE!!

 

[jimbopalmer]

in my first post

tcaddoo comments on the above:
You have to go into monitor mode and type flags.  At this point, it will walk you through 5 questions, one of which is whether to use factory defaults or not.

are you sure you are doing this step?

I tried to remain child-like, all I acheived was childish.

 

[Morvac]

Well, to be honest. I'm not sure. I'm pressing 'any key to stop autoboot' to enter monitor> mode then entering the commands specified. (see output in previous post) Is this what you mean?
---------------------
Press any key to stop autoboot

monitor> config sys set flags factorydefault true
monitor> save config
boot configuration has been saved
ip configuration has been saved
monitor> boot

---------
Continues to boot however im never prompted for any further information. Boots to the normal Login: prompt

 

[Seve]

As Jimbo say's, just type flags.

Monitor> flags (CR)

It will respond with -
Do you want to enable autoboot (y/n) ?
Do you want to enable factory defaults (y/n) ?

Etc

 

[Morvac]

Seve,
Thanks - That was exactly what I needed. I'm just not familar with bay commands yet. Worked perfectly (factory default) as well as the default passwords.

MANY THANKS to ALL!