A TSW problem with IOSII 2

[MDUserSergey]

Hello.

I have a problem. I want to save a continuous config data by DUSYI, and change an old Flash-HDU on my LIM1 NIU2 by another one Toshiba 128 Mb (comes from Ericsson). And work wirh it. But not all commands are work !!
I do next command file:
BLEQI:EQU=1-1-00-0;
FIMOE:SUBFS=SYSSUBFS11;
FIMOE:SUBFS=SYSSUBFS21;
IOSIE:NODE=SYSN,IODEV=SYSDISK1;
IOSII:NODE=SYSN,IODEV=SYSDISK1,SUBFS=SYSSUBFS11&SYSSUBFS21,BTYPE=ATA;
FICRI:SUBFS=SYSSUBFS11,SIZE=60;
Y;
FICRI:SUBFS=SYSSUBFS21,SIZE=60;
Y;
FIMOI:SUBFS=SYSSUBFS11,PATH=/SYSN/USR1;
FIMOI:SUBFS=SYSSUBFS21,PATH=/SYSN/USR2;
BLEQE:EQU=1-1-00-0;
FIDIIATH=/SYSN/USR1/SES/DR/REL1;
FIDIIATH=/SYSN/USR2/SES/DR/REL2;

But it work fine only due to a IOSII command. IOSII command not work:
<IOSII:NODE=SYSN,IODEV=SYSDISK1,BTYPE=ATA,SUBFS=SYSSUBFS11&SYSSUBFS21;
NOT ACCEPTED
SLAVE
ALREADY INITIATED

But really as SYSDISK1, as SYSSUBFS11&SYSSUBFS21 not exist !! What can I do to make IOSII ?

 

[whosrdaddy]

please start by posting your original IODDP;

/Daddy

-----------------------------------------------------
Helping people is my job...

 

[MDUserSergey]

<IODDP;
I/O DEVICE DATA
NODE IODEV/SUBFS BPOS/EQU I/O-BUS TYPE/USAGE STATUS AUTH
SYSN - 001-1-00 - - IN SERVICE
SYSN SYSTERMINAL 001-1-00-1 - MML - 7
SYSN MODEM 001-1-00-2 - MML - 7
SYSN MODEM-1 001-1-00-3 - MML - 7
SYSN SYSNET 001-1-00-4 - NETWORK/MML - 7
SYSNOLD - 009-0-60 - - IN SERVICE
SYSNOLD CILDISC 009-0-60-0 MASTER TOSHIBA IN SERVICE
CILSUBFS
SYSNOLD SYSTERMINAL2 009-0-60-1 - MML - 7
SYSNOLD CIL 009-0-60-3 - OUT IN SERVICE
SYSNOLD CILNET 009-0-60-4 - NETWORK/OUT IN SERVICE
SYSNOLD TELNET 009-0-60-4 - NETWORK/MML - 7
SAFETY - 012-1-00 - - IN SERVICE
SAFETY SAFETY-NET 012-1-00-4 - NETWORK/MML - 7
END

 

[MDUserSergey]

I solve this problem. A thread need to by closed. Don't reply.
Separately respect to whosrdaddy.

 

[whosrdaddy]

no need to close the thread,
maybe you can tell us what was the problem and how you solved it, so that this post can be helpful for other forum members

/Daddy

-----------------------------------------------------
Helping people is my job...

 

[MDUserSergey]

I'm not a teacher. And not speack fine. But whats happened - You see. Why - I do not know. What was I do ? I block NIU2, take off it from LIM1, insert it to test empty PBX TSW, power-on, burn a SYSN, Sysdisk1, SYS and SYSSUBFS11&SYSSUBFS21 (BTYPE=ATA) on same NIU2 + Flash-HDU, separate Flash-HDU of 256 Mb on 2 partitions of 128 Mb capacity each other, formatted both, makes REL1-directory, REL2, INL and ADD and not stop. I load to REL1, REL2, INL and ADD my real data (I save it just in case on my PC HDD) by FTP. It was a yesterdays data. Then I check a data by DUBCI it says that all 2 LIMs have a correct data. Then I take off NIU2 + Flash-HDU with correct data, insert it to my work PBX, in LIM1. And do RFEXI. It work a long time. But a PBX start to work well. After I check myself - do a 2 DUMPs one after one. All was coreect. And I see to ALLOP - he is empty. I enjoy and listen music. And what You want. Sorry my bad English.

 

[MDUserSergey]

Hi-hi-hix.
I come back to tell about that I screwed up another time. Without reason today DUMP to LIM1 NIU2 goes not work. Every times (today I try 6 times) TSW writes:
<DUSYI;
SYSTEM DUMP INFORMATION
NO VALID RELOAD DIRECTORY EXISTS
RESULT OF PASSIVE COMMON FUNCTIONS UPDATE
SUCCESSFUL
WAIT FOR DUMP TO LOCAL BACKUP
RESULT OF DUMP TO LOCAL BACKUP
SUCCESSFUL
RESULT OF DUMP TO EXTERNAL BACKUP


PERMISSION DENIED 23:10 11JUN15
FAILED FOR DIRECTORY REL1

END

It is shaped a disgrace ! It's a strike ! А Rise of the Machines. What can I do ? A PBX is big and work hard. I'm afraid to stop it ! A right data work only in the PBX memory. I forgot to save a yesterday DUMP !!! Only 5 june DUMP. It's very old. All the week I done many of changes ... How must I repear a RELs ?

Any minutes ago I delete a content of REL1 to make a DUMP to it another one time. But It not work ! I done RFPUI: LIM1, Unit=NIP; and later to Unit=FIH. But DUMP not work !! But FTP to this NIU2 work fine ... What can I do ?

 

[whosrdaddy]

No need to panic, as long as your PBX does not fall without power, there is no problem.
Just install a new disk and use the commands from your first post and redo a dump.

/Daddy

-----------------------------------------------------
Helping people is my job...

 

[MDUserSergey]

to Whosrdaddy:
Yes. No panic. Now I do a PC-Regen. And next shall format a new Flash-HDU, send there an old REL1, INL and ADD and RFEXI from they. No another way ... Need to do accurately ... No another way ...

 

[whosrdaddy]

no need for rfexi!
just put in a new HDU, reformat and do a dump

/Daddy

-----------------------------------------------------
Helping people is my job...

 

[MDUserSergey]

to Whosrdaddy:
Yes, interesting. But I try it about 6 times. No positive result. What I doing ? I install a new Flash-HDU, try to format it, but it ignore my IOSII command all the times ! It's an unknown big fatal TSW soft problem.
When I see that I can not win it - You are right - I make in an empty magazine a new TSW, with my NIU2 with my IPA, format a new Flash-HDU there, do an INL directory, insert to a Flash a fine working REL1,2 by FTP. Then switch-off an empty TSW. Then insert my NIU2+Flash-HDU in a working big TSW and RFEXI. No another way ... Bc that DUMP It rise successfully. And I load a new configuration by PC-Regen. Next done a 2 DUMP and so on. About 6 hours subscribers are loud to me. But now I have a fine working TSW, it can do a successful DUMPs. I do a DUFQI and see - it works fine.
I win it. And what You want.