3904 System Wide Firmware Upgrade 3

[undertaker48]

I have a Meridian 1 61c PBX, went to do a system wide upgrade of the firmware,ld 32 fdls 3904, stated it was Building tree... then stated stopped download (5)Friday. Is there a set up or command I missed to get this fdls to work.
Let me know the procedure to get this fdls 3904 to work. Can ld 97 cause this problem? I have Sessions 4.5
Thank you for your help.

Undertaker48

Your Help Is Greatly Appreciated.
Thank You
Undertaker48

 

[bigindian65]

Look at MVP on right of Web page, click on John Poole. Look at his FAQ by Meridian. It is on firmware setup/flash. Check your setup against his instructions.

 

[johnpoole]

usually the timer runs out.. max time will not usually allow a full systemwide download.. i would schedule one ipe or maybe a full card.. if you block 4 hours your going to get just over a card and a half.. 10 to 15 minutes per

john poole
bellsouth business
columbia,sc

 

[MrPederman]

Here is a document I made up.

This is an example of a scheduled download of (5) 3904 sets with TN’s of 52-0-11-0 through 52-0-11-4.
One interval is scheduled to take place on Thursday at 3:00am for a maximum time of 2 hours

>ld 97
SCSYS000
MEM AVAIL: (U/P): 23534388 USED U P: 4855751 429313 TOT: 28819452
DISK SPACE NEEDED: 698 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)

REQ chg
TYPE fdl
FDTP 3904
FDTM yes – Say yes if you want to schedule the download, Say no if want it to start immediately

FDAY 5 1 – FDAY d n Day and number of time intervals for download (if you said yes to FDTM)
d= (0-6) Day of the week, Sunday to Saturday
n= (0-4) Number of intervals where 0= no download for that day
note: If two or more intervals are specified, they must be non overlapping,
non consecutive and in increasing order.
FDAY is re-prompted until <cr> is entered.

FINT 3 2 – FINT s l Starting hour and length for a time interval.
s= (0-23) Starting hour using 24 hour format
l= (1-24) Length of interval in hours
FINT is prompted n times if Number of Intervals is > 0

FDAY <cr> -- FDAY is re-prompted until <cr> is entered.

FTNR yes – Say yes to download to specific range of TNs, Do not say no to this or all 3904’s will download

FSTN 52 0 11 0 – Loop, Card, Shelf, Unit Starting terminal number for download

FETN 52 0 11 4 – Loop, Card, Shelf, Unit Ending terminal number for download

FDNR no – enter no because we don’t want to select specific DN’s for download.

FRCE yes – Say yes to force the download regardless of the 3904’s current flash firmware version.

FVER <cr>


MEM AVAIL: (U/P): 23534388 USED U P: 4855751 429313 TOT: 28819452
DISK SPACE NEEDED: 698 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)

REQ ****
OVL000





Now that the schedule is create, we must activate it to run

>ld 32
NPR000
.fdls – This command initiates the system wide flash download to all or the specified 3904 sets according to
the parameters specified in LD 97 FDL configuration

BUILDING TREE ..

TRIGGERING DOWNLOAD NOW

>
TIM661 14:52 30/6/2004 CPU 1

SDL005 M3900 DOWNLOAD STOP HOUR (14 )WEDNESDAY -- This is what you see after FDLS successfully
completes is startup of the schedule.


This is what you will see in the PBX during the time the downloads are taking place.

TIM661 03:00 2/7/2004 CPU 1

SDL004 M3900 DOWNLOAD START HOUR (3 )FRIDAY

SDL001 STARTING DNLG 52 0 11 0

DTC001

SDL000 3904(52 0 11 0 ), VERSION 83, BKGD MODE.

SDL001 STARTING DNLG 52 0 11 1

TIM661 03:15 2/7/2004 CPU 1

SDL000 3904(52 0 11 1 ), VERSION 83, BKGD MODE.

SDL001 STARTING DNLG 52 0 11 2

DTC001

SDL000 3904(52 0 11 2 ), VERSION 83, BKGD MODE.

SDL001 STARTING DNLG 52 0 11 3

TIM661 03:30 2/7/2004 CPU 1

SDL000 3904(52 0 11 3 ), VERSION 83, BKGD MODE.

SDL001 STARTING DNLG 52 0 11 4

SDL000 3904(52 0 11 4 ), VERSION 83, BKGD MODE.

SDL002 M3900 DOWNLOAD COMPLETED -- All were downloaded successfully

TIM661 03:45 2/7/2004 CPU 1
You can check the firmware level of the phones specified in LD 97’s schedule by using the FSUM ALL or individually by using the command FWVU L S C U command in load 32

ld 32
NPR000
.fwvu 52 0 11 0

AUD000
****M3900 VERSION REPORT****
TERMINAL TYPE = 020
CORE FIRMWARE VERSION = 024
FLASH FIRMWARE VERSION = 083 – We are looking for this 083

.fsum all
TYPE:3904 CUST:00 PDN:773803 TN:052 0 11 00 FW:083 – Or this 083
TYPE:3904 CUST:00 PDN:773804 TN:052 0 11 01 FW:083
TYPE:3904 CUST:00 PDN:773805 TN:052 0 11 02 FW:083
TYPE:3904 CUST:00 PDN:773806 TN:052 0 11 03 FW:083
TYPE:3904 CUST:00 PDN:773807 TN:052 0 11 04 FW:083