I was notified of the phones on our system not coming up this morning. The alarms LEDs were all flashing so I consoled into the Maintenance port and this is the output....
MITEL SYSTEM ROM R2.1/1 May 9 2006 (83)
CCA Number : 56003040 RB.2
System Model : 003b0000 F250
CPU Model : 8260 R0060
Reset Config : 04043047
Bus Clock (MHz) : 66
CPM Clock (MHz) : 165
Core Clock (MHz) : 297
Internal Memory Map : f0000000
Main Memory (MB) : 256
Local Memory (MB) : 16
Flash Memory (MB) : 2
MAC Address : 08000f10f118
MMC CPLD : R2
ATA CPLD : R2
POST Bypass : 0
Watchdog Bypass : 0
Slot Id : 0
Starting POST...
SDRAM CS1 Data Bit Walk 1................... PASSED
SDRAM CS1 Data Bit Walk 0................... PASSED
SDRAM CS2 Data Bit Walk 1................... PASSED
SDRAM CS2 Data Bit Walk 0................... PASSED
LOCAL Mem Data Bit Walk 1................... PASSED
LOCAL Mem Data Bit Walk 0................... PASSED
SDRAM CS1 Address Walk 1................... PASSED
SDRAM CS1 Address Walk 0................... PASSED
SDRAM CS2 Address Walk 1................... PASSED
SDRAM CS2 Address Walk 0................... PASSED
LOCAL Mem Address Walk 1................... PASSED
LOCAL Mem Address Walk 0................... PASSED
SDRAM CS1 March Test........................ PASSED
SDRAM CS2 March Test........................ PASSED
LOCAL Mem March Test........................ PASSED
Starting vxWorks...
VxWorks System Boot
Copyright 1984-2002 Wind River Systems, Inc.
CPU: Mitel Embedded PPC82XX F250
Version: VxWorks5.5.1
BSP version: 2.1/1
Creation date: May 9 2006, 15:46:27
Press <SPACE><SPACE><SPACE> to stop auto-boot AFTER countdown starts...
<7><6><5><4><3><2><1><0>
auto-booting...
boot device : ata=auto
unit number : 0
processor number : 0
host name : bootHost
file name : /partition1/Rtc8260
inet on ethernet (e) : 192.9.201.35:ffffff00
host inet (h) : 172.25.18.30
gateway inet (g) : 192.9.201.5
user (u) : mnms
ftp password (pw) : mx2000
flags (f) : 0x0
target name (tn) : VoiceTest
other (o) : motfcc
Disk Configuration Started.
Creating block device for controller 0 drive 0... done.
Creating CBIO device for controller 0 drive 0... done.
Attaching to partition table for 4 partitions on controller 0 drive 0... done.
Creating Cache Layer for partition 0 (/ata00) on controller 0 drive 0... done.
Creating Dos FS device for partition 0 (/ata00) on controller 0 drive 0... done.
Disk Configuration Complete.
Loading /ata00/Rtc8260...55013824
Starting at 0x10000...
Disk Configuration Started.
Creating block device for controller 0 drive 0... done.
Creating CBIO device for controller 0 drive 0... done.
Attaching to partition table for 4 partitions on controller 0 drive 0... done.
Creating Cache Layer for partition 0 (/sysro) on controller 0 drive 0... done.
Creating Cache Layer for partition 1 (/db) on controller 0 drive 0... done.
Creating Cache Layer for partition 2 (/vmail) on controller 0 drive 0... done.
Creating Dos FS device for partition 0 (/sysro) on controller 0 drive 0... done.
Creating Dos FS device for partition 1 (/db) on controller 0 drive 0... done.
Creating Dos FS device for partition 2 (/vmail) on controller 0 drive 0... done.
Disk Configuration Complete.
0xffffe00 (tRootTask): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0xffffe00 (tRootTask): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0xffffe00 (tRootTask): dosFsLib.c : ERROR reading the device boot sector
0xffffe00 (tRootTask): dosFsLib.c : media not formatted or not present
0xffffe00 (tRootTask): dosFsLib.c : Problem finding volume data, trying to use the next block as boot block.
0xffffe00 (tRootTask): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
volume descriptor ptr (pVolDesc): 0xfb21ec8
cache block I/O descriptor ptr (cbio): 0xfb2fde0
auto disk check on mount: DOS_CHK_REPAIR | DOS_CHK_VERB_1
max # of simultaneously open files: 202
file descriptors in use: 0
# of different files in use: 0
# of descriptors for deleted files: 0
# of obsolete descriptors: 0
can't mount volume
0xffffe00 (tRootTask): dosFsLib.c : Malformed boot sector. Offset 0, value 82.
0xffffe00 (tRootTask): dosFsLib.c : Ensure this device is formatted and par
titions are properl/db/y handled.
- disk check in progress ...
dosChkLib : CLOCK_REALTIME is being reset to FRI DEC 30 22:59:28 2022
Value obtained from file system volume descriptor pointer: 0xfb28e00
The old setting was THU JAN 01 00:16:24 1970
Accepted system dates are greater than THU DEC 27 00:00:00 1990
/db/ - Volume is OK
total # of clusters: 1,128,488
# of free clusters: 1,122,801
# of bad clusters: 0
total free space: 17,543 Mb
max contiguous free space: 17,277,124,604 bytes
# of files: 734
# of folders: 150
total bytes in files: 80,346 Kb
# of lost chains: 0
total bytes in lost chains: 0
volume descriptor ptr (pVolDesc): 0xfb28e00
cache block I/O descriptor ptr (cbio): 0xfbafe70
auto disk check on mount: DOS_CHK_REPAIR | DOS_CHK_VERB_1
max # of simultaneously open files: 202
file descriptors in use: 0
# of different files in use: 0
# of descriptors for deleted files: 0
# of obsolete descriptors: 0
current volume configuration:
- volume label: NO LABEL ; (in boot sector: )
- volume Id: 0xa8870000
- total number of sectors: 36,129,240
- bytes per sector: 512
- # of sectors per cluster: 32
- # of reserved sectors: 32
- FAT entry size: FAT32
- # of sectors per FAT copy: 8,821
- # of FAT table copies: 2
- # of hidden sectors: 0
- first cluster is in sector # 17,674
- Update last access date for open-read-close = FALSE
- directory structure: VFAT
- root dir start cluster: 2
FAT handler information:
------------------------
- allocation group size: 113 clusters
- free space on volume: 18,395,971,580 bytes
/sysro/ - disk check in progress ...
/sysro/ - Volume is OK
total # of clusters: 401,396
# of free clusters: 341,474
# of bad clusters: 0
total free space: 1,333 Mb
max contiguous free space: 496,058,368 bytes
# of files: 8,801
# of folders: 378
total bytes in files: 215,323 Kb
# of lost chains: 0
total bytes in lost chains: 0
volume descriptor ptr (pVolDesc): 0xfb2fd38
cache block I/O descriptor ptr (cbio): 0xfbd0348
auto disk check on mount: DOS_CHK_REPAIR | DOS_CHK_VERB_1
max # of simultaneously open files: 202
file descriptors in use: 0
# of different files in use: 0
# of descriptors for deleted files: 0
# of obsolete descriptors: 0
current volume configuration:
- volume label: NO LABEL ; (in boot sector: )
- volume Id: 0x1dd0000
- total number of sectors: 3,217,473
- bytes per sector: 512
- # of sectors per cluster: 8
- # of reserved sectors: 32
- FAT entry size: FAT32
- # of sectors per FAT copy: 3,143
- # of FAT table copies: 2
- # of hidden sectors: 0
- first cluster is in sector # 6,318
- Update last access date for open-read-close = FALSE
- directory structure: VFAT
- root dir start cluster: 2
FAT handler information:
------------------------
- allocation group size: 41 clusters
- free space on volume: 1,398,677,504 bytes
Attached TCP/IP interface to motfcc unit 0
Attaching interface lo0...done
Adding 127552 symbols for standalone.
Last reset cause was (0x83) POWER_ON_RESET
->
There is no host relink.
There is no relink on the disk.
30/12/2022 22:59:50> SoftLog - WARNING - MSPLogServer - OtpLogs.cpp(57)
PostSoftwareLogA: Called before calling OtpLogStartup
30/12/2022 22:59:50> SoftLog - INFO - MIFSM - MiFsmEventUtil.cpp(25)
Internal Message
RegisterEventUtil - Task: N/A
Registering event utility for FSM engine ID 0
30/12/2022 22:59:50> SoftLog - INFO - MIFSM - MiFsmEventUtil.cpp(25)
Internal Message
RegisterEventUtil - Task: N/A
Registering event utility for FSM engine ID 2
relink_call_ctors start
relink_call_ctors done
Executing S10startup script
Copy OK: 695 bytes copied
...Creating appStartup.log
24/08/2009 23:51:38> SoftLog - WARNING - MSPLogServer - OtpLogs.cpp(600)
OtpLogStartup: Log server already started. Request ignored.
OtpLogs_Toggle: The following software logs are enabled:
ERROR & WARNING
OtpMaintenanceLogs_Toggle: The following maintenance logs are enabled:
ERROR & WARNING & INFO
MiSslInit(): entry
MiSeedRand(): Start RandStatus = 0
MiSeedRand(): End RandStatus = 1
DSC:
rocessArguments - (option -debug)
Debug level set to level 0 -> OSA_ERROR_SEVERITY
SysServices::appStartup: Logs to be redirected to DataServices!
deleting file /db/database/__db.001
Copy OK: 57344 bytes copied
Database verification passed: /db/database/files/hdrswlog.db
MON AUG 24 23:51:39 2009
Database verification failed: /db/database/files/pstswlog.db2
appendFile(): /db/logFile.rtf has become too big.
Database verification passed: /db/database/files/registry.db
Database verification passed: /db/database/files/sysconfg.db
Database verification passed: /db/database/files/wbsspddl.db
Database verification passed: /db/database/files/wbsspdlb.db
Database verification passed: /db/database/files/bookmark.db
Database verification passed: /db/database/files/bookmklb.db
Database verification passed: /db/database/files/prsnldir.db
Database verification passed: /db/database/files/calllogs.db
Database verification passed: /db/database/files/keylabls.db
Database verification passed: /db/database/files/ipconsol.db
Database verification passed: /db/database/files/webstapp.db
Database verification passed: /db/database/files/wsonlser.db
Database verification passed: /db/database/files/alrmctgy.db
Database verification passed: /db/database/files/sysalrmd.db
Database verification passed: /db/database/files/usrprfle.db
Database verification passed: /db/database/files/xaregapp.db
Database verification passed: /db/database/files/vmhntgrp.db
Database verification passed: /db/database/files/wireless.db
Database verification passed: /db/database/files/vmnumprt.db
Database verification passed: /db/database/files/prstcnfg.db
Database verification passed: /db/database/files/vmoption.db
Database verification passed: /db/database/files/vmemail.db
Database verification passed: /db/database/files/nrkelemt.db
Database verification passed: /db/database/files/opsmangr.db
Database verification passed: /db/database/files/dmal2dat.db
Database verification passed: /db/database/files/mixmlapp.db
Database verification passed: /db/database/files/mixmlfeat.db
Database verification passed: /db/database/files/netelmcr.db
Database verification passed: /db/database/files/dsttrnlog.db
Database verification passed: /db/database/files/distpayl.db
Database verification passed: /db/database/files/dstupdat.db
Database verification passed: /db/database/files/icpclust.db
Database verification passed: /db/database/files/clicppbx.db
Database verification passed: /db/database/files/udmntcfg.db
Database verification passed: /db/database/files/udmaccnt.db
Database verification passed: /db/database/files/lcimetad.db
Database verification passed: /db/database/files/lcimembr.db
Database verification passed: /db/database/files/lclneid.db
Database verification passed: /db/database/files/unseqnbr.db
Database verification passed: /db/database/files/neprops.db
Database verification passed: /db/database/files/lciclscp.db
Database verification passed: /db/database/files/lcideftn.db
Database verification passed: /db/database/files/deideftn.db
Database verification passed: /db/database/files/dercddst.db
Database verification passed: /db/database/files/clstrmbr.db
Database verification passed: /db/database/files/vqsmeta.db
Database verification passed: /db/database/files/vqstats.db
Database verification passed: /db/database/files/audtmeta.db
Database verification passed: /db/database/files/auditlog.db
Database verification passed: /db/database/files/sippeers.db
Database verification passed: /db/database/files/siproute.db
Database verification passed: /db/database/files/pginfo.db
Database verification passed: /db/database/files/pginfhl.db
Database verification passed: /db/database/files/sysipass.db
Database verification passed: /db/database/files/spteluri.db
Database verification passed: /db/database/files/spotprxy.db
Database verification passed: /db/database/files/sipnecor.db
Database verification passed: /db/database/idbfiles/idbver.db
Database verification passed: /db/database/idbfiles/iLinkProp.db
Database verification passed: /db/database/idbfiles/iPCallNSF.db
Database verification passed: /db/database/idbfiles/iPCallHLC.db
Database verification passed: /db/database/idbfiles/iCPNinfo.db
Database verification passed: /db/database/idbfiles/iCPNdata.db
Database verification passed: /db/database/idbfiles/iIDC.db
Database verification passed: /db/database/idbfiles/iRLK.db
Database verification passed: /db/database/idbfiles/iODR.db
Management Layer AVS SUCCESSFULLY started.
ChubSp SUCCESSFULLY started.
System wide Component Monitoring is DISABLED.
Current system reset mode: [0]
ResourceAlarmStartup ready.
Database verification passed: /db/ipndb/odb/files/MitelDhcpClientEntry.wdb
Database verification passed: /db/ipndb/odb/files/MitelDhcpServerGeneral.wdb
Database verification passed: /db/ipndb/odb/files/MitelDhcpServerSubnet.wdb
Database verification passed: /db/ipndb/odb/files/MitelDhcpServerRange.wdb
Database verification passed: /db/ipndb/odb/files/MitelDhcpServerStaticIp.wdb
Database verification passed: /db/ipndb/odb/files/MitelDhcpServerOption.wdb
Database verification passed: /db/ipndb/odb/files/MitelDhcpServerLease.wdb
Database verification passed: /db/ipndb/odb/files/MitelIpGrpFilter.wdb
Database verification passed: /db/ipndb/odb/files/MitelFltGrpAccessRestrict.wdb
Database verification passed: /db/ipndb/odb/files/MitelMIPSLan.wdb
Database verification passed: /db/ipndb/odb/files/MitelMIPSWan.wdb
Database verification passed: /db/ipndb/odb/files/MitelMIPSPptp.wdb
Database verification passed: /db/ipndb/odb/files/MitelMIPSSwitch.wdb
Database verification passed: /db/ipndb/odb/files/MitelMIPSSwGrpPort.wdb
Database verification passed: /db/ipndb/odb/files/MitelPPPGrpPPPoE.wdb
Database verification passed: /db/ipndb/odb/files/MitelIpLogGrpLog.wdb
Database verification passed: /db/ipndb/odb/files/PppSecuritySecretsTable.wdb
Database verification passed: /db/ipndb/odb/files/IpCidrRouteTable.wdb
Database verification passed: /db/ipndb/odb/files/MitelIpGrpDns.wdb
Database verification passed: /db/ipndb/odb/files/MitelDiffServ.wdb
Retrieved memory size 0x10000000
Set Emulator to NORMAL
Call Engine Layer Coordinator SUCCESSFULLY started.
Reminder: use -d option when running dbasrv from command line.
UDT msgsys userID is 231079048.
ENABLING COMMANDS
Database verification passed: /db/nvmdb/files/databver.db
Database verification passed: /db/nvmdb/files/nvmusers.db
IPN DBA Starting up!!
No Email Params found... Email Task not started.
adding names to certificate
added CN = mitel networks 3300 icp web server
added CN = vxtarget
added CN = 10.40.135.132
added CN = voicetest
added CN = 192.9.200.35
added CN = 192.9.201.35
cert modified
0xb621c50: SetTransportMode: TCPUnicast
ENABLING COMMANDS
Management Layer SUCCESSFULLY started.
Start DHCP service
Start DNS-QryMgr service
MCC initializing with H.110 TDM Bus connectivity.
0x366d380 (tAppStartup):
DW pool created with 2560 buffers, platform: 250
Initialized and enabled Mcc1.
Initialized and enabled Mcc2.
-----> Mitel E2T initializing <-----
E2T Startup: E2T IP address = 192.9.201.35
E2T Startup: RTC IP address = 192.9.201.35
Stream_T2E_Startup, binding 64 RTP ports (even ports) in the range of 50000 to 50126
There were 64 UDP ports created.
Stream_T2E_Startup, binding 64 RTCP ports (odd ports) in the range of 50001 to 50127
There were 64 RTCP ports created.
tMediaControl E2t<->E2tProxy MCT communications established
E2T Startup: TDM codec is U_LAW_CODEC
Dsp List Filename: "/sysro/DspConfig/dsplist.txt"
Dsp Config Filename: "/sysro/DspConfig/dspConfig3300.txt"
Dsp Card Type Filename: "/sysro/DspConfig/DspCardType.txt"
Dsp Type Filename: "/sysro/DspConfig/DspType3300.txt"
Dsp Dynamic Loading Filename: "/sysro/DspConfig/loading3300.txt"
E2tProxy<->E2t Communications Channel is UP
INFO EchoCanceller InitEcHwInfo VEC_64 in midplane slot 4 [pasic 4]
Service Layer Coordinator SUCCESSFULLY started.
Network Service Layer Coordinator SUCCESSFULLY started.
Starting up VM Corp Dir...
...Fault detected while starting up VM Corp Dir. Please ignore if Voice mail networking is not enabled.
Starting up SMTP Client
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
25/08/2009 00:00:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following WARNING log could not be posted.
File: Cipvm_CD.cpp(1757), Source: AL -- IPVMCD,
LogMsg: Cipvm_CD::Startup()
Failed to refresh the NVM server cache. Please check the NVM Servers table or ignore this warning if Voicemail networking is not enabled.
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
25/08/2009 00:04:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following WARNING log could not be posted.
File: ipvm_ap.cpp(417), Source: AL -- IPVMAP,
LogMsg: Fault detected while starting up VM Corp Dir. If Voice mail networking is not enabled, please ignore this warning.
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x3661700 (tAppStartup): dosFsLib.c : ERROR reading the device boot sector
0x3661700 (tAppStartup): dosFsLib.c : media not formatted or not present
0x3661700 (tAppStartup): dosFsLib.c : Problem finding volume data, trying to use the next block as boot block.
25/08/2009 00:08:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following ERROR log could not be posted.
File: ESM_OPSAlarms_DSA.cpp(1611), Source: OPS Alarms DSA,
LogMsg: ForwardUDTMessageToOPS()->Cannot connect to UDTHANDLER
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
25/08/2009 00:12:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following ERROR log could not be posted.
File: ESM_OPSAlarms_DSA.cpp(1611), Source: OPS Alarms DSA,
LogMsg: ForwardUDTMessageToOPS()->Cannot connect to UDTHANDLER
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x3661700 (tAppStartup): dosFsLib.c : Malformed boot sector. Offset 0, value 82.
0x3661700 (tAppStartup): dosFsLib.c : Ensure this device is formatted and partitions are properly handled.
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
25/08/2009 00:16:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following ERROR log could not be posted.
File: ESM_OPSAlarms_DSA.cpp(1611), Source: OPS Alarms DSA,
LogMsg: ForwardUDTMessageToOPS()->Cannot connect to UDTHANDLER
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
25/08/2009 00:20:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following ERROR log could not be posted.
File: ESM_OPSAlarms_DSA.cpp(1611), Source: OPS Alarms DSA,
LogMsg: ForwardUDTMessageToOPS()->Cannot connect to UDTHANDLER
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x3661700 (tAppStartup): dosFsLib.c : ERROR reading the device boot sector
0x3661700 (tAppStartup): dosFsLib.c : media not formatted or not present
0x3661700 (tAppStartup): dosFsLib.c : Problem finding volume data, trying to use the next block as boot block.
25/08/2009 00:24:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following ERROR log could not be posted.
File: ESM_OPSAlarms_DSA.cpp(1611), Source: OPS Alarms DSA,
LogMsg: ForwardUDTMessageToOPS()->Cannot connect to UDTHANDLER
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
25/08/2009 00:28:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following WARNING log could not be posted.
File: log_outputs_util_en.c(2085), Source: Call Control - Software,
LogMsg: DBMS - DBREFUTIL Function : Save_Pages_On_File
Operation : End_Transaction File : transient
Return Code : Device timeout
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x3661700 (tAppStartup): dosFsLib.c : Malformed boot sector. Offset 0, value 82.
0x3661700 (tAppStartup): dosFsLib.c : Ensure this device is formatted and partitions are properly handled.
25/08/2009 00:32:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following WARNING log could not be posted.
File: log_outputs_util_en.c(2085), Source: Call Control - Software,
LogMsg: OS (Message) warning: Receiver process not found.
Redun code: $02 $02 $02
TX/RX msid: $00 $01 $00 $00 $00 $00 $01 $00 $00 $00
TX/RX pid: ($0003,$0012) mssint ($0007,$0006) ----------
appl/func: $0E $01
active pid: ($0003,$0012) mssint
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
25/08/2009 00:36:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following WARNING log could not be posted.
File: log_outputs_util_en.c(2085), Source: Call Control - Software,
LogMsg: DBMS - DBREFUTIL Function : Save_Pages_On_File
Operation : End_Transaction File : transient
Return Code : Device timeout
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x3661700 (tAppStartup): dosFsLib.c : ERROR reading the device boot sector
0x3661700 (tAppStartup): dosFsLib.c : media not formatted or not present
0x3661700 (tAppStartup): dosFsLib.c : Problem finding volume data, trying to use the next block as boot block.
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x3661700 (tAppStartup): dosFsLib.c : Malformed boot sector. Offset 0, value 82.
0x3661700 (tAppStartup): dosFsLib.c : Ensure this device is formatted and partitions are properly handled.
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
*** WARNING: Startup incomplete after 1800.000 sec. Task StartupHwRst resetting system. ***
I have read other posts with similar problems but they all mentioned the Disk Drive LED as being red whereas mine is still Green.
Any help at all is appreciated.
MITEL SYSTEM ROM R2.1/1 May 9 2006 (83)
CCA Number : 56003040 RB.2
System Model : 003b0000 F250
CPU Model : 8260 R0060
Reset Config : 04043047
Bus Clock (MHz) : 66
CPM Clock (MHz) : 165
Core Clock (MHz) : 297
Internal Memory Map : f0000000
Main Memory (MB) : 256
Local Memory (MB) : 16
Flash Memory (MB) : 2
MAC Address : 08000f10f118
MMC CPLD : R2
ATA CPLD : R2
POST Bypass : 0
Watchdog Bypass : 0
Slot Id : 0
Starting POST...
SDRAM CS1 Data Bit Walk 1................... PASSED
SDRAM CS1 Data Bit Walk 0................... PASSED
SDRAM CS2 Data Bit Walk 1................... PASSED
SDRAM CS2 Data Bit Walk 0................... PASSED
LOCAL Mem Data Bit Walk 1................... PASSED
LOCAL Mem Data Bit Walk 0................... PASSED
SDRAM CS1 Address Walk 1................... PASSED
SDRAM CS1 Address Walk 0................... PASSED
SDRAM CS2 Address Walk 1................... PASSED
SDRAM CS2 Address Walk 0................... PASSED
LOCAL Mem Address Walk 1................... PASSED
LOCAL Mem Address Walk 0................... PASSED
SDRAM CS1 March Test........................ PASSED
SDRAM CS2 March Test........................ PASSED
LOCAL Mem March Test........................ PASSED
Starting vxWorks...
VxWorks System Boot
Copyright 1984-2002 Wind River Systems, Inc.
CPU: Mitel Embedded PPC82XX F250
Version: VxWorks5.5.1
BSP version: 2.1/1
Creation date: May 9 2006, 15:46:27
Press <SPACE><SPACE><SPACE> to stop auto-boot AFTER countdown starts...
<7><6><5><4><3><2><1><0>
auto-booting...
boot device : ata=auto
unit number : 0
processor number : 0
host name : bootHost
file name : /partition1/Rtc8260
inet on ethernet (e) : 192.9.201.35:ffffff00
host inet (h) : 172.25.18.30
gateway inet (g) : 192.9.201.5
user (u) : mnms
ftp password (pw) : mx2000
flags (f) : 0x0
target name (tn) : VoiceTest
other (o) : motfcc
Disk Configuration Started.
Creating block device for controller 0 drive 0... done.
Creating CBIO device for controller 0 drive 0... done.
Attaching to partition table for 4 partitions on controller 0 drive 0... done.
Creating Cache Layer for partition 0 (/ata00) on controller 0 drive 0... done.
Creating Dos FS device for partition 0 (/ata00) on controller 0 drive 0... done.
Disk Configuration Complete.
Loading /ata00/Rtc8260...55013824
Starting at 0x10000...
Disk Configuration Started.
Creating block device for controller 0 drive 0... done.
Creating CBIO device for controller 0 drive 0... done.
Attaching to partition table for 4 partitions on controller 0 drive 0... done.
Creating Cache Layer for partition 0 (/sysro) on controller 0 drive 0... done.
Creating Cache Layer for partition 1 (/db) on controller 0 drive 0... done.
Creating Cache Layer for partition 2 (/vmail) on controller 0 drive 0... done.
Creating Dos FS device for partition 0 (/sysro) on controller 0 drive 0... done.
Creating Dos FS device for partition 1 (/db) on controller 0 drive 0... done.
Creating Dos FS device for partition 2 (/vmail) on controller 0 drive 0... done.
Disk Configuration Complete.
0xffffe00 (tRootTask): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0xffffe00 (tRootTask): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0xffffe00 (tRootTask): dosFsLib.c : ERROR reading the device boot sector
0xffffe00 (tRootTask): dosFsLib.c : media not formatted or not present
0xffffe00 (tRootTask): dosFsLib.c : Problem finding volume data, trying to use the next block as boot block.
0xffffe00 (tRootTask): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
volume descriptor ptr (pVolDesc): 0xfb21ec8
cache block I/O descriptor ptr (cbio): 0xfb2fde0
auto disk check on mount: DOS_CHK_REPAIR | DOS_CHK_VERB_1
max # of simultaneously open files: 202
file descriptors in use: 0
# of different files in use: 0
# of descriptors for deleted files: 0
# of obsolete descriptors: 0
can't mount volume
0xffffe00 (tRootTask): dosFsLib.c : Malformed boot sector. Offset 0, value 82.
0xffffe00 (tRootTask): dosFsLib.c : Ensure this device is formatted and par
titions are properl/db/y handled.
- disk check in progress ...
dosChkLib : CLOCK_REALTIME is being reset to FRI DEC 30 22:59:28 2022
Value obtained from file system volume descriptor pointer: 0xfb28e00
The old setting was THU JAN 01 00:16:24 1970
Accepted system dates are greater than THU DEC 27 00:00:00 1990
/db/ - Volume is OK
total # of clusters: 1,128,488
# of free clusters: 1,122,801
# of bad clusters: 0
total free space: 17,543 Mb
max contiguous free space: 17,277,124,604 bytes
# of files: 734
# of folders: 150
total bytes in files: 80,346 Kb
# of lost chains: 0
total bytes in lost chains: 0
volume descriptor ptr (pVolDesc): 0xfb28e00
cache block I/O descriptor ptr (cbio): 0xfbafe70
auto disk check on mount: DOS_CHK_REPAIR | DOS_CHK_VERB_1
max # of simultaneously open files: 202
file descriptors in use: 0
# of different files in use: 0
# of descriptors for deleted files: 0
# of obsolete descriptors: 0
current volume configuration:
- volume label: NO LABEL ; (in boot sector: )
- volume Id: 0xa8870000
- total number of sectors: 36,129,240
- bytes per sector: 512
- # of sectors per cluster: 32
- # of reserved sectors: 32
- FAT entry size: FAT32
- # of sectors per FAT copy: 8,821
- # of FAT table copies: 2
- # of hidden sectors: 0
- first cluster is in sector # 17,674
- Update last access date for open-read-close = FALSE
- directory structure: VFAT
- root dir start cluster: 2
FAT handler information:
------------------------
- allocation group size: 113 clusters
- free space on volume: 18,395,971,580 bytes
/sysro/ - disk check in progress ...
/sysro/ - Volume is OK
total # of clusters: 401,396
# of free clusters: 341,474
# of bad clusters: 0
total free space: 1,333 Mb
max contiguous free space: 496,058,368 bytes
# of files: 8,801
# of folders: 378
total bytes in files: 215,323 Kb
# of lost chains: 0
total bytes in lost chains: 0
volume descriptor ptr (pVolDesc): 0xfb2fd38
cache block I/O descriptor ptr (cbio): 0xfbd0348
auto disk check on mount: DOS_CHK_REPAIR | DOS_CHK_VERB_1
max # of simultaneously open files: 202
file descriptors in use: 0
# of different files in use: 0
# of descriptors for deleted files: 0
# of obsolete descriptors: 0
current volume configuration:
- volume label: NO LABEL ; (in boot sector: )
- volume Id: 0x1dd0000
- total number of sectors: 3,217,473
- bytes per sector: 512
- # of sectors per cluster: 8
- # of reserved sectors: 32
- FAT entry size: FAT32
- # of sectors per FAT copy: 3,143
- # of FAT table copies: 2
- # of hidden sectors: 0
- first cluster is in sector # 6,318
- Update last access date for open-read-close = FALSE
- directory structure: VFAT
- root dir start cluster: 2
FAT handler information:
------------------------
- allocation group size: 41 clusters
- free space on volume: 1,398,677,504 bytes
Attached TCP/IP interface to motfcc unit 0
Attaching interface lo0...done
Adding 127552 symbols for standalone.
Last reset cause was (0x83) POWER_ON_RESET
->
There is no host relink.
There is no relink on the disk.
30/12/2022 22:59:50> SoftLog - WARNING - MSPLogServer - OtpLogs.cpp(57)
PostSoftwareLogA: Called before calling OtpLogStartup
30/12/2022 22:59:50> SoftLog - INFO - MIFSM - MiFsmEventUtil.cpp(25)
Internal Message
RegisterEventUtil - Task: N/A
Registering event utility for FSM engine ID 0
30/12/2022 22:59:50> SoftLog - INFO - MIFSM - MiFsmEventUtil.cpp(25)
Internal Message
RegisterEventUtil - Task: N/A
Registering event utility for FSM engine ID 2
relink_call_ctors start
relink_call_ctors done
Executing S10startup script
Copy OK: 695 bytes copied
...Creating appStartup.log
24/08/2009 23:51:38> SoftLog - WARNING - MSPLogServer - OtpLogs.cpp(600)
OtpLogStartup: Log server already started. Request ignored.
OtpLogs_Toggle: The following software logs are enabled:
ERROR & WARNING
OtpMaintenanceLogs_Toggle: The following maintenance logs are enabled:
ERROR & WARNING & INFO
MiSslInit(): entry
MiSeedRand(): Start RandStatus = 0
MiSeedRand(): End RandStatus = 1
DSC:
Debug level set to level 0 -> OSA_ERROR_SEVERITY
SysServices::appStartup: Logs to be redirected to DataServices!
deleting file /db/database/__db.001
Copy OK: 57344 bytes copied
Database verification passed: /db/database/files/hdrswlog.db
MON AUG 24 23:51:39 2009
Database verification failed: /db/database/files/pstswlog.db2
appendFile(): /db/logFile.rtf has become too big.
Database verification passed: /db/database/files/registry.db
Database verification passed: /db/database/files/sysconfg.db
Database verification passed: /db/database/files/wbsspddl.db
Database verification passed: /db/database/files/wbsspdlb.db
Database verification passed: /db/database/files/bookmark.db
Database verification passed: /db/database/files/bookmklb.db
Database verification passed: /db/database/files/prsnldir.db
Database verification passed: /db/database/files/calllogs.db
Database verification passed: /db/database/files/keylabls.db
Database verification passed: /db/database/files/ipconsol.db
Database verification passed: /db/database/files/webstapp.db
Database verification passed: /db/database/files/wsonlser.db
Database verification passed: /db/database/files/alrmctgy.db
Database verification passed: /db/database/files/sysalrmd.db
Database verification passed: /db/database/files/usrprfle.db
Database verification passed: /db/database/files/xaregapp.db
Database verification passed: /db/database/files/vmhntgrp.db
Database verification passed: /db/database/files/wireless.db
Database verification passed: /db/database/files/vmnumprt.db
Database verification passed: /db/database/files/prstcnfg.db
Database verification passed: /db/database/files/vmoption.db
Database verification passed: /db/database/files/vmemail.db
Database verification passed: /db/database/files/nrkelemt.db
Database verification passed: /db/database/files/opsmangr.db
Database verification passed: /db/database/files/dmal2dat.db
Database verification passed: /db/database/files/mixmlapp.db
Database verification passed: /db/database/files/mixmlfeat.db
Database verification passed: /db/database/files/netelmcr.db
Database verification passed: /db/database/files/dsttrnlog.db
Database verification passed: /db/database/files/distpayl.db
Database verification passed: /db/database/files/dstupdat.db
Database verification passed: /db/database/files/icpclust.db
Database verification passed: /db/database/files/clicppbx.db
Database verification passed: /db/database/files/udmntcfg.db
Database verification passed: /db/database/files/udmaccnt.db
Database verification passed: /db/database/files/lcimetad.db
Database verification passed: /db/database/files/lcimembr.db
Database verification passed: /db/database/files/lclneid.db
Database verification passed: /db/database/files/unseqnbr.db
Database verification passed: /db/database/files/neprops.db
Database verification passed: /db/database/files/lciclscp.db
Database verification passed: /db/database/files/lcideftn.db
Database verification passed: /db/database/files/deideftn.db
Database verification passed: /db/database/files/dercddst.db
Database verification passed: /db/database/files/clstrmbr.db
Database verification passed: /db/database/files/vqsmeta.db
Database verification passed: /db/database/files/vqstats.db
Database verification passed: /db/database/files/audtmeta.db
Database verification passed: /db/database/files/auditlog.db
Database verification passed: /db/database/files/sippeers.db
Database verification passed: /db/database/files/siproute.db
Database verification passed: /db/database/files/pginfo.db
Database verification passed: /db/database/files/pginfhl.db
Database verification passed: /db/database/files/sysipass.db
Database verification passed: /db/database/files/spteluri.db
Database verification passed: /db/database/files/spotprxy.db
Database verification passed: /db/database/files/sipnecor.db
Database verification passed: /db/database/idbfiles/idbver.db
Database verification passed: /db/database/idbfiles/iLinkProp.db
Database verification passed: /db/database/idbfiles/iPCallNSF.db
Database verification passed: /db/database/idbfiles/iPCallHLC.db
Database verification passed: /db/database/idbfiles/iCPNinfo.db
Database verification passed: /db/database/idbfiles/iCPNdata.db
Database verification passed: /db/database/idbfiles/iIDC.db
Database verification passed: /db/database/idbfiles/iRLK.db
Database verification passed: /db/database/idbfiles/iODR.db
Management Layer AVS SUCCESSFULLY started.
ChubSp SUCCESSFULLY started.
System wide Component Monitoring is DISABLED.
Current system reset mode: [0]
ResourceAlarmStartup ready.
Database verification passed: /db/ipndb/odb/files/MitelDhcpClientEntry.wdb
Database verification passed: /db/ipndb/odb/files/MitelDhcpServerGeneral.wdb
Database verification passed: /db/ipndb/odb/files/MitelDhcpServerSubnet.wdb
Database verification passed: /db/ipndb/odb/files/MitelDhcpServerRange.wdb
Database verification passed: /db/ipndb/odb/files/MitelDhcpServerStaticIp.wdb
Database verification passed: /db/ipndb/odb/files/MitelDhcpServerOption.wdb
Database verification passed: /db/ipndb/odb/files/MitelDhcpServerLease.wdb
Database verification passed: /db/ipndb/odb/files/MitelIpGrpFilter.wdb
Database verification passed: /db/ipndb/odb/files/MitelFltGrpAccessRestrict.wdb
Database verification passed: /db/ipndb/odb/files/MitelMIPSLan.wdb
Database verification passed: /db/ipndb/odb/files/MitelMIPSWan.wdb
Database verification passed: /db/ipndb/odb/files/MitelMIPSPptp.wdb
Database verification passed: /db/ipndb/odb/files/MitelMIPSSwitch.wdb
Database verification passed: /db/ipndb/odb/files/MitelMIPSSwGrpPort.wdb
Database verification passed: /db/ipndb/odb/files/MitelPPPGrpPPPoE.wdb
Database verification passed: /db/ipndb/odb/files/MitelIpLogGrpLog.wdb
Database verification passed: /db/ipndb/odb/files/PppSecuritySecretsTable.wdb
Database verification passed: /db/ipndb/odb/files/IpCidrRouteTable.wdb
Database verification passed: /db/ipndb/odb/files/MitelIpGrpDns.wdb
Database verification passed: /db/ipndb/odb/files/MitelDiffServ.wdb
Retrieved memory size 0x10000000
Set Emulator to NORMAL
Call Engine Layer Coordinator SUCCESSFULLY started.
Reminder: use -d option when running dbasrv from command line.
UDT msgsys userID is 231079048.
ENABLING COMMANDS
Database verification passed: /db/nvmdb/files/databver.db
Database verification passed: /db/nvmdb/files/nvmusers.db
IPN DBA Starting up!!
No Email Params found... Email Task not started.
adding names to certificate
added CN = mitel networks 3300 icp web server
added CN = vxtarget
added CN = 10.40.135.132
added CN = voicetest
added CN = 192.9.200.35
added CN = 192.9.201.35
cert modified
0xb621c50: SetTransportMode: TCPUnicast
ENABLING COMMANDS
Management Layer SUCCESSFULLY started.
Start DHCP service
Start DNS-QryMgr service
MCC initializing with H.110 TDM Bus connectivity.
0x366d380 (tAppStartup):
DW pool created with 2560 buffers, platform: 250
Initialized and enabled Mcc1.
Initialized and enabled Mcc2.
-----> Mitel E2T initializing <-----
E2T Startup: E2T IP address = 192.9.201.35
E2T Startup: RTC IP address = 192.9.201.35
Stream_T2E_Startup, binding 64 RTP ports (even ports) in the range of 50000 to 50126
There were 64 UDP ports created.
Stream_T2E_Startup, binding 64 RTCP ports (odd ports) in the range of 50001 to 50127
There were 64 RTCP ports created.
tMediaControl E2t<->E2tProxy MCT communications established
E2T Startup: TDM codec is U_LAW_CODEC
Dsp List Filename: "/sysro/DspConfig/dsplist.txt"
Dsp Config Filename: "/sysro/DspConfig/dspConfig3300.txt"
Dsp Card Type Filename: "/sysro/DspConfig/DspCardType.txt"
Dsp Type Filename: "/sysro/DspConfig/DspType3300.txt"
Dsp Dynamic Loading Filename: "/sysro/DspConfig/loading3300.txt"
E2tProxy<->E2t Communications Channel is UP
INFO EchoCanceller InitEcHwInfo VEC_64 in midplane slot 4 [pasic 4]
Service Layer Coordinator SUCCESSFULLY started.
Network Service Layer Coordinator SUCCESSFULLY started.
Starting up VM Corp Dir...
...Fault detected while starting up VM Corp Dir. Please ignore if Voice mail networking is not enabled.
Starting up SMTP Client
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
25/08/2009 00:00:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following WARNING log could not be posted.
File: Cipvm_CD.cpp(1757), Source: AL -- IPVMCD,
LogMsg: Cipvm_CD::Startup()
Failed to refresh the NVM server cache. Please check the NVM Servers table or ignore this warning if Voicemail networking is not enabled.
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
25/08/2009 00:04:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following WARNING log could not be posted.
File: ipvm_ap.cpp(417), Source: AL -- IPVMAP,
LogMsg: Fault detected while starting up VM Corp Dir. If Voice mail networking is not enabled, please ignore this warning.
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x3661700 (tAppStartup): dosFsLib.c : ERROR reading the device boot sector
0x3661700 (tAppStartup): dosFsLib.c : media not formatted or not present
0x3661700 (tAppStartup): dosFsLib.c : Problem finding volume data, trying to use the next block as boot block.
25/08/2009 00:08:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following ERROR log could not be posted.
File: ESM_OPSAlarms_DSA.cpp(1611), Source: OPS Alarms DSA,
LogMsg: ForwardUDTMessageToOPS()->Cannot connect to UDTHANDLER
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
25/08/2009 00:12:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following ERROR log could not be posted.
File: ESM_OPSAlarms_DSA.cpp(1611), Source: OPS Alarms DSA,
LogMsg: ForwardUDTMessageToOPS()->Cannot connect to UDTHANDLER
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x3661700 (tAppStartup): dosFsLib.c : Malformed boot sector. Offset 0, value 82.
0x3661700 (tAppStartup): dosFsLib.c : Ensure this device is formatted and partitions are properly handled.
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
25/08/2009 00:16:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following ERROR log could not be posted.
File: ESM_OPSAlarms_DSA.cpp(1611), Source: OPS Alarms DSA,
LogMsg: ForwardUDTMessageToOPS()->Cannot connect to UDTHANDLER
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
25/08/2009 00:20:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following ERROR log could not be posted.
File: ESM_OPSAlarms_DSA.cpp(1611), Source: OPS Alarms DSA,
LogMsg: ForwardUDTMessageToOPS()->Cannot connect to UDTHANDLER
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x3661700 (tAppStartup): dosFsLib.c : ERROR reading the device boot sector
0x3661700 (tAppStartup): dosFsLib.c : media not formatted or not present
0x3661700 (tAppStartup): dosFsLib.c : Problem finding volume data, trying to use the next block as boot block.
25/08/2009 00:24:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following ERROR log could not be posted.
File: ESM_OPSAlarms_DSA.cpp(1611), Source: OPS Alarms DSA,
LogMsg: ForwardUDTMessageToOPS()->Cannot connect to UDTHANDLER
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
25/08/2009 00:28:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following WARNING log could not be posted.
File: log_outputs_util_en.c(2085), Source: Call Control - Software,
LogMsg: DBMS - DBREFUTIL Function : Save_Pages_On_File
Operation : End_Transaction File : transient
Return Code : Device timeout
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x3661700 (tAppStartup): dosFsLib.c : Malformed boot sector. Offset 0, value 82.
0x3661700 (tAppStartup): dosFsLib.c : Ensure this device is formatted and partitions are properly handled.
25/08/2009 00:32:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following WARNING log could not be posted.
File: log_outputs_util_en.c(2085), Source: Call Control - Software,
LogMsg: OS (Message) warning: Receiver process not found.
Redun code: $02 $02 $02
TX/RX msid: $00 $01 $00 $00 $00 $00 $01 $00 $00 $00
TX/RX pid: ($0003,$0012) mssint ($0007,$0006) ----------
appl/func: $0E $01
active pid: ($0003,$0012) mssint
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
25/08/2009 00:36:21> SoftLog - ERROR - LogPuller - LogStateReport.cpp(629)
Error GE_FAIL(0x60000000) Posting log to subscribing log clients.
The following WARNING log could not be posted.
File: log_outputs_util_en.c(2085), Source: Call Control - Software,
LogMsg: DBMS - DBREFUTIL Function : Save_Pages_On_File
Operation : End_Transaction File : transient
Return Code : Device timeout
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x3661700 (tAppStartup): dosFsLib.c : ERROR reading the device boot sector
0x3661700 (tAppStartup): dosFsLib.c : media not formatted or not present
0x3661700 (tAppStartup): dosFsLib.c : Problem finding volume data, trying to use the next block as boot block.
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
0x3661700 (tAppStartup): dosFsLib.c : Malformed boot sector. Offset 0, value 82.
0x3661700 (tAppStartup): dosFsLib.c : Ensure this device is formatted and partitions are properly handled.
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x368c4c0 (tDhcpServr): dhcp_s_build_lease_info: Both range and lease fields are NULL !!
0x3661700 (tAppStartup): disk cache error: device fb2fde0 block 0 errno c0003, disk read failed
*** WARNING: Startup incomplete after 1800.000 sec. Task StartupHwRst resetting system. ***
I have read other posts with similar problems but they all mentioned the Disk Drive LED as being red whereas mine is still Green.
Any help at all is appreciated.