1XP Portal R8 signaling DDI for incoming call to Mobile Android device

[djmtrar]

Android APP R8 Mobile Preferred.... ( Of course, out local network )

When I make a call the signal is trasmited to the 1XP portal over internet..... but when I receive a call, the number DDI for this incomming call it's signaling ( 3g/egprs/gprs )to my android device?....

This question is because in my country you can't send original DDI's to other lines....

Example :

Trunk 1 incomming call from 555-5555555, the call is routing to my GSM GATEWAY to my celular ( SMARTPHONE device ) but the numbre in the screen of my movile phone is the numbre of the GSM GATEWAY.

Thnaks.




Regards!
Djmtrar

 

[tlpeter]

That is normal.
You are being called by the IPO.
when you answer then the IPO will call the number you have dialed.


BAZINGA!

I'm not insane, my mother had me tested!

 

[djmtrar]

Thanks for your answer Tlpeter, but I think I have not explained well or do not understand me.

I'm mean, if a customer calls you to the office and you pass the call to the phone or receive it through twinning. In my country, the network will not send the phone number of the caller. The question is whether the Preferred mobile solutions and application for android that can be done. Receive DDI of the caller to the ipo y my mobil phone.

Comdasys has a mobility solution for Avaya and other manufacturers to do so.

Regards!
Djmtrar

 

[tlpeter]

Here in Europe you ar enot allowed to send the original number but there is an option for this in the IPO.
When you are allowed to send the number and the provider does allow you too then you must set it on the tab system -> twinning
check the option for sending the original number.


BAZINGA!

I'm not insane, my mother had me tested!

 

[djmtrar]

Thanks again Tlpeter.....

I'm in Europe too...., and for this, my question. I know how to set for send the option in the ipo for send the original number.

The question is for the R8, and the new Movile preferred solution with Android.

Do you know Comdasys movile solutions? Well, My question is if the new solution of the R8 is like Comdasys.

In Comdasys, the original number is sending via data to the movil phone, the you can anwer the call knowing who is calling..



Regards!
Djmtrar

 

[tlpeter]

I know Comdasys, some colleagues use it.
Comdasys is a sip application anduses internal twinning and thus it is not like 1X mobile.


BAZINGA!

I'm not insane, my mother had me tested!

 

[djmtrar]

Sorry Tlpeter,

Comdasys, depending the version, can use in your smartphone WIFI, 3g, or GSM, if you can use in time one or other. When you use, GSM the number dialed is sent by DATA ( GPRS, ERGP, or 3G, depending the signal ), and when you receive a call via IPO, the number of the original call it is receiving via DATA too...




Regards!
Djmtrar

 

[tlpeter]

I know but i don't use it.

But you need to create a sip user and twin it to your deskphone.
You need sip trunks to the Comdasys unit too.

If needed then it is nice but i need mobile twinning.


BAZINGA!

I'm not insane, my mother had me tested!

 

[djmtrar]

So, so... for this, the reason of my question. IPO signaling via DATA to the android APP the caller number of the incomming call to the mobile when twinning?



Regards!
Djmtrar

 

[tlpeter]

No, it does not do that.


BAZINGA!

I'm not insane, my mother had me tested!