Search results for query: *

Thanks everyone for the input. It is now up and running just fine. We just had to run the 'ENLC 6 0 2' to enable the card (ISDLC card, I believe) to have it working. Although the status showed as idle, the card just didn't kick in after the reboot correctly. Once again thank you all for your...

We only use the handset. Thanks for the suggestion.

.... I noticed, that after reboot, my phone (ten 6.0.9.6) is idle and has a dial tone and all but is acting up little funny. It seems to have this delay for primary dn button. Even when I tried to make an outbound call, the number input seems to be really slow and can get to complete the...

Unfortunately the spare console phone yielded same error. * After a reset the console phone displays '01-Jan-89 09:00 AM' and cannot get the console phone to come out of the 'night' mode. (All other phones show correct time) * Diagnostic of the phone shows 'Data Port Failure Code A0H'...

The 6 0 2 3 is a regular user phone (2008). I did try disu and enlu on the 4 TNs as well but with no result. I believe I do have a spare console phone. Let me give that a try and see if it will do the trick. Thanks everyone for your help, I'll be sure to post the result soon!

Got it! and thank you for the post. Here it is and they are all disabled!! enlu command did not work and returned NPR 674 error it is a console power unit. How can I put them into enlu state?? TN 006 0 02 04 TYPE PWR CDEN 4D DATE 2 FEB 1996 TN 006 0 02 05 TYPE PWR CDEN 4D DATE 2...

Thank you for the feed back. Here is the output. The TN shows up as enabled. REQ: prt TYPE: 2250 TN CUST DATE PAGE TN 006 0 02 01 TYPE 2250 CDEN 4D CUST 0 SGRP 0 SETN 006 0 02 02 ANUM 01 IADN 4550 ALPD NO SSU ICDR ICDD ABAN ABDD CPND CNDA AADN 4550 DNDI DNDA DAPC DAPA LANG 00...

I have physically disconnected the 25 pin connector from back of the console phone as well as from the diagnostic menu. Would this be implementing it via the amp cable. If not can you show me how! Thank you

Hello everyone, Here are the series of clues to my problem... * Had to do a PBX reboot (Had to... Company upgraded the generator and for the electrical work, the vendors had to cut the circuits and all of our systems had to come down for some time.) * Everything seemed fine, but * Our...

I did use the number (1-700-555-4141) and verified that the carrier is AT&T. When I said both, I mean that both of the PIC codes are from AT&T... We only use one carrier and only receive bill from one carrier! I don't think you are understding what I'm saying, the calls are going to the right...

It's AT&T. As you know SBC is now AT&T. Both of PIC codes 10372 (Pre-merger Pacific Bell) and PIC code 10288 (The new AT&T code for ABN)belongs to them. Few months ago we've migrated from one product to another product but still in the same company AT&T which saves us phone bill on our...

They are both AT&T. The issue is which PIC code from within the AT&T network is being used.... Either way, I did not see any DMI when I printed ALL of the DMI table, and not just for one route....

Maybe you've initially typed the NPA as 827 instead of 1827 ...

Thanks for the advise. I actually did verify that all of the calls go our via the same RLI (9) and via same route (8) which is our 20 inbound/outbound trunks. Also, the NPA that I looked up in the PBX was the NPA that was captured and was billed by the Long-distance carrier (the bill in...

The ESN0072 Error means that the specified NXX already exists... You may want to do a NXX print out and make sure that the NXX does not exist alreay. LD 90 REQ PRT CUST 0 FEAT net TRAN ac1 type NXX This should list all the NXX... Hope this helps.

Thank you all so much for sharing in-depth knowledge. I feel that I've come out with better understanding of how the outbound calls are routed. Just to share my findings... I've looked for from our phone bill, an area code call that was billed by our Long-distance carrier. 254 (Waco, TX)...

Just to give some background info. Our carrier is telling us that we may have a wrong PIC code configured in our system. They are saying that we are using Old 10372 PIC code instead of the new 10288 PIC code to route our outbound long distance calls. I don't see any of the two PIC codes in...

Thank you for the feed back. When I ran the load this is what I see... SPN 0 FLEN 0 INPL NO RLI 22 SDRR NONE ITEI NONE SPN 011 FLEN 0 INPL YES RLI 7 ALOW 53 SDRR ALOW CODES = 1 ITEI NONE SPN 102 FLEN 0 RLI 0 SDRR NONE ITEI NONE SPN 1411 FLEN 0 RLI 0 SDRR NONE ITEI NONE...

Hi, I was wondering if someone could gide me on how to see/change the PIC (Pre-subscribed/Primary Inter-LATA Carrier code) for Nortel Option 61C. What load should I go into? I need to see if the current PIC code is 10372 (Pre-merger Pacific Bell) and if so change it to PIC code 10288 (The...

Once again, thank you all for your support. I've eventually solved the issue. It turns out that after the reboot, the RLI has reverted to previous configuration. When I ran a tracked a call, I noticed that it was trying to go out via a trunk that no longer existed. I made changes to the RLB...