Search results for query: *

PBXJay, can you elaborate more?? I just had this happen on a Legend RLS 5 today...same issue and I am 4 hours from it!!! (I miss my old ROLMs!) The old craft password is not working...the new password (xxxxxx) just causes WinSPM to lock up and my CPU util to go to 100%!!! YIKES! ASA?? I am not...

Upgraded an Opt81C to RLS 4.5 CS1000...redundant sig servers and everything....at a remote office, they went with all iP phones (though we could have done this with a remote fiber shelf we had spare and plenty of TDM phones..nice to blow $300k+ on phones!)...for Faxes and modems, they bought...

I dont think you can format the HARD drive from the commands...FORMAT does the floppies (remember PM uses OS/2 not DOS; close but not close enough) The FAT tables and attributes are different for OS2 vs DOS and then there is some special file allocation done by IBM/ROLM in the firmware (remember...

QSIG is optional in most PBXs...Siemens and Nortel can talk QSIG between them...via ISDN PRI. Cornet is for Siemens-Siemens (or ROLMs with 9006m software) only. Have the NTPs from Nortel (CS1000/Option Meridian PBX) and Siemens both (TDM and IP, talk about begging :). You can find the Siemens...

There is a shutdown procedure for the Nortsar NAMs...and I bet the Mini may have one also....just pulling the plug is never good for any CPU controlled device IF there is a shutdown setting...Let me search my files but I suspect you have already done this? Chris

Houstontelecom at earthlink dot net Thanks!

Never have seen that but does the user have a VM Box? Does dialing the DN for voicemail work? Have them fwd their phone to the VM DN and see what happens...I have three of them right now and no issues with them...

BTW the 9200 does do LCR/Route Op (better than an 8000!)where as the Deadwood would NOT! SO I would take a 9200 over a Redwood any day..and even over a Nortel KSU (Gawd I hate working on a Nortel KSU..the DID interface sucks and no decent routing control on calls...well, the MICS is better than...

The 9200 was a renamed HICOM 200 box put under a ROLM model number....but its the same box..sorry for the delay but just read it tonight...need any help? Drop me an email at Houstontelecom at earthlink dot net.

Dartlvr, I think the 9006i is 6.5 or 6.6...but I know 6.3 could not do Qsig...when did they add Qsig?? If so, I would like to talk to you in pvt about it...we definitely want to get the Option 11C and HCM talking....(of course they have two HCMs not talking in PRI, Cornet or QSIG so they can...

Have a 9006i/HCM300 V6.5 currently connected to a Nortel Opt11 via T1 over fiber...want to change it to PRI so we can pass CLID between the switches. What would be the best setup on that (I know it can work NI2..but what is the best way to set it up)? I want to make the HCM the "CO" end of the...

Have a 9006i/HCM300 V6.5..currently connected to a Nortel Opt11 via T1 over fiber...want to change it to PRI so we can pass CLID between the switches. What would be the best setup on that (I know it can work NI2..but what is the best way to set it up)? I want to make the HCM the "CO" end of the...

How much do you want for it?? Last one I bought off EBay was 200 for the whole systems w/PM and RPs.. Dr_Touchtone :>

Just a note...the original ROLM (Now SiemensROLM) mail list is at www.tgrace.com ....scroll down and click on the link to the telecom mail lists at the bottom. The original Nortel list is there as well....over 2000 Nortel users active and probably 1/2 that on ROLM.... The ROLM List supports all...

As a Siemens trained person (now referred to as Expert because I understood it!) on the HCM200/ROLM 9200, I can say even IF you have the manuals and software (EMMA) to talk to the switch, you have a long way to go...it is a PITA to work with....but granted, the switch WORKS and WORKS and...