Search results for query: *

LD 15 REQ: CHG TYPE: FTR OPT: CPD (Call Park Denied)

BRI.

I'm guessing since they are M3905 models that they're ACD? Have you got Call Force call presentation turned on for any agents?

You'll have to get creative regardless of the handset lifter (GN Netcom or Plantronics). I've been cutting up foam and using that to fill in the curves and strong double sided tape. Good luck!

You'd have to program up your AUB block, assign AUTH codes, change the NCOS and TGAR of the phone, if necessary. Check your outbound Rtes for the TARG. That's a start.

Disable DCH in LD 96, disable trunks in LD 60, out DCH in LD 17 and then out trunk members in LD 14, out Route in LD 16.

LD 60 and at the . you'll type STAT 34 That should show you all of your channels on your loop. I'm betting you don't see anything going on with channel 8 though. Also, if you need to take down that loop, don't forget to disable the DCH first in 96. Good luck!

In LD 21 do the following: REQ PRT TYPE RDR_DATA CUST 0 I'm betting you have MWFB NO If so, do the following: LD 15 REQ CHG TYPE RDR_DATA CUST 0 Hit return until MWFB and type YES return all the way out. What this means is DID calls to busy telephones routed to Message Center. When set to NO...

Paging on a phone is a key system function rather than a PBX function. Unless you're meaning an overhead paging system? If so, then it's allowing access to the ACOD of the paging route. Or you can certainly use the flexible feature codes. Give us more info and we can point you in the right...

Is the problem you're having with the called party not seeing your main number? Or is the 2250's display does not show the number calling? If it's the display then you'll need to go into LD 15 and change the ATT_DATA and add IDP to your OPT. If it's the called party can't see numbers...

LD 21 REQ: PRT TYPE: ATT_DATA In addition, you may want to print out your LDN_DATA as well. Same overlay, just change the TYPE to LDN.

You also can look in LD 21 at your RDR_DATA. Check what you have for CFN0, CFN1, CFN2. The number following will indicate how many ring cycles prior to Forward No Answer/Hunt a call goes to it's destination. On the phone's TN itself, check the RCO which corresponds with the number following...

Yes, LD 2 does show the change on both ends and there are no errors.

I've got a remote site using a CS1000B and use Element Manager. This site is in the East and my site (81C) is in the West. I've tried changing the time on both but the East site still is 1 hour off, though that time isn't registered in either site. Anyone out there know what the next steps...

Have each user recycle their phone individually. Just unplug the power supply and then plug it back in.

I am constantly getting a BUG5157 scrolling and don't know how to fix it. The NTP is vague. Any suggestions? % BUG5157 % BUG5157 : 00000004 00000001 00000009 000000EC % BUG5157 + 00AE3570 00A8EFD5 00A830D8 00A822A7 00A86F4F % BUG5157 + 00530063 0038E634 0038E4F2 0036DB4F 00542C55 %...

You also want to ensure your CDNs are in there as well as your Skillsets. As dsennet pointed out, if you have existing scripts, you shouldn't have a problem other than modifying to the actual new skillset. Post back with your specifics and you're sure to get assistance.