Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. geo2500

    VPN Configuration

    The netscreen is not capable of terminating VPN connections? We have a pix firewall instead of the netscreen25 and we terminate the connections there. For the clients to get LAN visibility you should give them an internal ip address, internal dns and then open the firewall for the internal IPs...
  2. geo2500

    Dual Hub, Dual DMVPN connection

    Hi all, We are interested in implementing a Dual Hub Dual DMVPN solution and I would like to ask the following. Cisco says that only the primary hub is used for traffic and the second hub is used for backup, but we would like the spoke router to send/receive traffic on both HUBs depending on the...
  3. geo2500

    PIX 501 - Traffic not getting out

    icmp is not stateful, so you need to allow to allow icmp on the outbound interface
  4. geo2500

    Help plz, how do I map 129.34.11.12 port 81 to 10.5.1.3 port 81

    what you are doing is Port Redirection. You 'd better look at the manuals or at cisco's website for the proper way of doing it.
  5. geo2500

    Deny all from inside. Then allow specific ports after. How?

    you can also try using the pdm to configure your pix firewall and access-lists. It's much much easier and more user friendly. try https://your-pix-ip
  6. geo2500

    DDR - Deny RIP traffic

    one thing I forgot to mention the s0/1/0 is not connected.
  7. geo2500

    DDR - Deny RIP traffic

    Hi again, this is the conf. To explain a bit this is part of a test bed, it's not production. I have two routers listening on the same ethernet segment and being HSRP enabled. I want when the first one goes down, this one to bring up the ISDN link and call the other side. So I want the isdn link...
  8. geo2500

    DDR - Deny RIP traffic

    Hi I have an isdn link that I want to get up for all other traffic except RIP. I tried access-list 101 deny udp any host 224.0.0.9 eq rip access-list 101 permit ip any any dialer-list 1 protocol ip list 101 but then the isdn link never comes up i have also a static route for all traffic to...
  9. geo2500

    User can receive but not make calls (Option11C - M2008)

    Guys thanks for your answers the phone should be the problem, I asked for a replacement
  10. geo2500

    User can receive but not make calls (Option11C - M2008)

    Sorry I wasn't clear. he can't make internal calls either As far as ncos is concerned he has the same as the other users
  11. geo2500

    User can receive but not make calls (Option11C - M2008)

    Hi guys, I have a user who is complaining that he can receive but not make any calls (either local or outgoing). IDU returns the type of the device (M2008) and stat returns it is idle the programming on the TN looks similar like in the other phones. Does it ring any bell? or are there any...
  12. geo2500

    PIX stops responding once or twice a day?

    Since you bought this pix will failover licence, this is the norm. The router will restart once a day. It's mentioned at Cisco's site. This is done because the pix with failover licence costs much less than a pix with normal licence. Otherwise, everybody would buy the cheap solution. A pix with...
  13. geo2500

    Do I need an acl to ping pcs on the inside int from the pix?

    I have a pix 501 and I would like to ping the hosts connected on the inside interface from the pix. Do I need an acl for that? thanks
  14. geo2500

    Can your ISP see what sites you been on?

    in UK ISPs are required by law to record what sites each user has visited. They are also going to pass a similar law in eu (if they haven't done it already). Also all telephone call details are recorded in eu, under the law for terrorism, which was voted by the european parliament a few months...
  15. geo2500

    When I have two equal cost paths in RIP, which one is used?

    Hi, I have a router A, which receives the same rip updates from 2 routers(B and C) with the same metric. Which one, will A use for sending packets to these networks? ps: B and C are for redundancy and when I install them, they will play HSRP. I just want to find out first, what will happen with...
  16. geo2500

    Strange Ping Problem between 2 routers and 2 hosts

    Hi guys, I have this setting Host1 <----> Router1 <----->Router2 <-----> Host2 Host1 can ping Host2 and vice versa Host1 can ping Router1, Router2 Host2 can ping Router2, Router1 Router1 cannot ping Host2 (but can ping host1 and router2) Router2 cannot ping Host1 (but can ping host2 and...
  17. geo2500

    Will UDP (RIP) pass through IPSEC &amp; TED?

    Just to make things clear, since RIPv2 uses multicast is it possible to be encrypted with IPSEC?
  18. geo2500

    Will UDP (RIP) pass through IPSEC &amp; TED?

    Hi, I am using a dynamic crypto map with TED to encrypt an ISDN connection. It seems that UDP (RIP) traffic is not forwarded. in the access list for crypto, it says that if you use ted, you can only specify IP protocol, not udp or tcp, so everything is encrypted. Does anybody have experience on...
  19. geo2500

    What are the WA_Sys_... indexes that I see on create index wizard?

    Hi, When I use the Create Index Wizard, after I select a table it displays the current indexes. The problem is that it lists an index for each column in the table although I haven't created them. (apart from the index for primary key which is auto created). The list is like that...
  20. geo2500

    Where can I set the collation during setup?

    Hi again, I have this question. All the manuals say that you should set collation during setup. However I have never seen asking me for collation settings when I do a typical install of sql server 2000. Do I need to do a custom install? Thanks, George

Part and Inventory Search

Back
Top