Search results for query: *

jlgon, To add to John's point. It's not the phone the connects to local 911 it is the VoIP phone system. There needs to be local gateways registered to the callmanger and specific route patterns built for 911 or 9.911 depending on your dial plan that instruct the callmanger to send the call...

Burgal, Are there any obstructions in the parking lot, metal poles, trees, etc that could be reflecting the signal. Keep in mind that visual line of site and RF line of site are two very different things. Also, using a 5.2 dbi antenna focuses the RF beam, decreasing your vertical beamwidth...

Ethernet channeling is the ability to group multiple switchports together in an etherchannel group to increase the bandwidth between two switches, usually used within core environments. The following link should help you with setting up this between 2950's...

Do you have multiple subnets in your network? If so is your Domain controller on the same subnet as your PC's and the DHCP server on a different subnet? If this is the case try placing an IP-helper address statement where the ip address is that of your dhcp server on your network on each...

When you think about VoIP networking the first thing is to make sure your cabling will support it, must be CAT5 or higher and I would have it certified to verify that all connections are good. Also, its a good practice to separate your voice traffic from your data traffic through the use of...

Make sure the Outlook process is not running is the Process tab under task manager. I have the same issue if I open Outlook and then close it I am unable to reopen it until I go into the task manager and kill the Outlook.exe process. It then opens fine. Hope this helps.

If am running office 2003 that interacts with Exchange 2003. On my workstation when I close outlook using the X button on the top corner of the screen it appears to close the application. However, when I try to open Outlook again it hangs. If I go into task manager and end the outlook.exe...

Thanks for the link, that's exactly what I was looking for.

I was hoping someone might know of a product that could help me out in my situation. We have a rather large VoIP environmnet and use IP conference phones. Our users have a bad habit of pulling out the network cables to use for laptop access and then don't plug the phones in correctly and due...

Does anyone know the command to set the boot image for the 3500 XL series switches. They are running IOS version 12.0(5.2)XU. The switches are not booting after a power cycle. When I do a show boot, they either do not have any image defined or are pointed to the wrong flash image. Thanks in...

Something that you could try is don't connect the switch to the network. At first just connect to the switch via console connection. Power the switch up and manually shut down the interfaces. After the switch has been powered up connect it to the network and bring up the interfaces. Hope this...

I am not very familiar with the products that are out there to support this particular issue so I was hoping that someone could make a recommendation. Here is what I need a product to do. It has to both power cycle a server if it would hang as well as be able to power one up from a down state...

The Cisco 3500XL and the newer 3550 series has the setup that you are looking for, however you will need to buy GBIC's to use the fiber connections. Hope this helps.

I would verify that you have an SSID setup and that the SSID on the wireless card in the laptop matches the SSID that you have set on the router.

I am using a Aironet 1200 series access point. I have it configured for VLAN management using WEP security and LEAP authentication. Everything is up and running fine. The issue that I am having is that when the Users's domain password expires, LEAP will not work. In order for the user to use...

For the life of me I cannot remember or seem to find the name of a cable that on one end can be connected to a 110 punch down block and on the other end of the cable is an RJ-45 connector. Thanks in advance for the help.

Hi all, I am trying to understand more about routers and I have a question about 1/255. I know that the 1 of 1/255 deals with the load currently on the router, what I am after what the 255 means. Thanks in advance. Alex

I have clients running windows XP that are connected to a 2003 network. On the machines locally I gave the users administrative rights, also on the domain I gave them admin rights, which I know I shouldn't really do but for testing issues I did. The users can log on to the domain but cannot...

I am running Server 2003 with multiple clients. I have granted the users of the clients administrator privleges. When users log on to the domain they cannot install software on their computer. Error message states that they need administrator priveleges to do so, but i have granted them such...

Ben, Create a new Organizational unit and name it sales. Then place the sales staff within this OU. This should set it up like you wanted. Hope this helps.