Search results for query: *

I"m looking for a compatiable server SFP ethernet card solution for mim signal loss connection. I'm deploying a cisco rtr with a Cisco SFP-10G-SR MM fiber connection to a intel 10 gig XF Server adapters which is 10G. But the problem is signal loss between the cisco transeciever and the server...

Can a cisco 6509 cpu spike crashes the device. Making it go into ROM Mode? Added an ip sla to the device and then the device crashed. 877778777987987670 475838776339956950 100...

I have a BGP session with a number peers on a vlan. The subnet is a /25 and I would like to change it to a /24. Will this subnet change restart the BGP session with the peers?

What type of cisco router configurations besides URPF can use to protect or slow down Slowloris attacks

I have a MPLS TE mesh network with OPSF as the link state protocol..All the tunnels are running in area 0...I have also created other areas..Will I run into any issues if I create stub areas with MPLS running on the backbone..

I have a 6506 and I'm upgrading to the 7606 S-Chasis. Will the line cards work in the 7606 S-Chasis? Is everything seamless from one device to the next.

it was a writers error on my part..I setup it to the other side of the router...

I have PBR setup on several of my routers. But it's not rerouting the traffic at all...currently I have a 10.1.1.0 network on the LAN coming to my router. The normal behavior is routing via the ospf.but I want it to go in a different direction across a T3...Am I missing something..Below is my...

Thanks..Last question for a 7613 what are the boot statements. I don't think there the regular statements are for this model... ex. boot system:disk0: boot system:disk1:

Question 1: I have a 7613 cisco router with two sup 32 engines.what variable determines the running IOS on two active sup engines? Question 2: Currently one of my sup 32 engines is in ROMMON mode, if I load my IOS on the failed engine. A. Will it return two standby HOT B. Will it supercede the...

I want to bundle two T3 using MPPP, but unfortunely cisco guidelines restrict the use of T3 bundling on this router. What other solution can I use besides MPPP? I want combine the two 45mbps so I can get the full use of a 90mbps pipe?

I have a request to do a dot1q trunk between a switch and a server...What are the disadavantages of doing this(spanning tree, broadcasts etc) and what are the configurations for server to do this.... P.S. If I do this can I configure the trunk to be an isolated port or community port?

your correct I have two routers in area 0(A and B), but the two routers are different connections.Router C is connected to router A currently in area 1 and Router D is conneted to router B in area 3... What I want I want to do is change Router D area id to 1..Will I run into any problems...Will...

I'm running ospf in my network and collasping the number of areas..Can I run two area 1's in my network.. For example: Router A is in the backbone with routers configured for area 1 Router B is in the backbone with routers also configured for area 1.. Will I run into any issues with this...

doesn't show any spikes during the 5 sec 1min or 5 min intervals

I have a 7204 cisco router with an OC3 card.Currently the rx and tx load is often at 150/155 145/155 during the day..The problem is the output drops is increasing my 5000 each 5 min cpu interval. But last friday the router began to hang, I rebooted it and it started working again..On Tuesday...

thanks..The OC12 will be handled through cisco 7304 router and then there will be gig ethernet drop off to the Nortel.. So I can assume the nortel 5000 will handle a max of 200mpbs of traffic

I have an OC-12(155mbps) pipe coming from an MPLS cloud into a CE router. What I need to know, what is the maximum speed for 1700 Nortel encryptor or do I need to another encryptor to balance the load. Or is there a Nortel encryptor that can handle an OC-12 pipe?

Hello everyone, This is regarding a stub area I'm trying to configure..Now I have a good understanding of stubbing an area...I curious let me explain.. I have two routers and two switches in area 0... The two routers all have area 0 connections in the backbone, but the switches have another...

My area 0 is doing constant recalculations, but the network is very big...I need a logging or snmp command to narrow down my search for the culprit... Besides log-adjancency-changes under the process, what other commands can I use to point to my syslog server?